American Architectural Millwork YU LOCKERS L-B-P-1T-151872 User manual

Instruction Manual
Single Tier Locker
L-B-P-1T-151872

I
Strike Plate
x 1
F
Mechanical Lock
x 1
G
Hinge
x 4
H
Smove Adapter
x 1
E
Robe Hook
x 2
D
Base Plate
x 4
C
Smove Holder
x 1
B
ClicFit Male Insert
x 30
A
ClicFit Female Insert
x 60
J
#6 Flathead Screw
x 16
K
#6 Roundhead Screw
x 2
L
#6 Ovalhead Screw
x 4
M
Left Side Panel
x 1
N
Back Panel
x 1
O
Right Side Panel
x 1
P
Door
x 1
Q
Top Shelf
Panel
x 1
R
Center Shelf
Panel
x 1
S
Bottom Shelf
Panel
x 1
Parts included:

Connect male connector B into side slot of female connector
A. Insert clip consisting of connector A and connector B into
the side edge of panel # making for a solid fit. Once clips are
inserted into panel they cannot be removed. Continue these
steps when inserting all 30 Male and Female combined clips.
Insert clip consisting of connector A into the top front facing
side of panel # making for a solid fit. Once clips are inserted
into panel they cannot be removed. Continue these steps
when inserting all 30 clips.
Robe Hooks (E1, E2) are placed over pre drilled holes on left
side panel (M.) and right side panel (O.). Once robe hooks
are aligned to pre drilled holes, secure hooks to panels (M.)
and (O.) using two #6 oval head screws (L.) using philips
head screwdriver.
Step 1:
Step 2:
Step 3:
B. A.
A.
L.
L.
E.

Step 4:
Step 5:
Step 6:
Base plate (D.) placed over pre-drilled holes on right side
panel (O.). Once Base plate (D) is aligned to pre drilled holes,
secure base plates to panel (O) using 7 #6 flathead screws
(J) using philips head screwdriver. Continue these steps to
install all 4 base plates (D), excluding bottom base plate. The
final base plate (D) will be secured using 1 #6 flathead screw
(J) in the bottom screw insert hole. Leaving the top screw
insert hole empty for the installation of Smove holder (C) and
Smove adapter (H), seen in steps 5 and 6.
Using the bottom base plate (D) slide the Smove adapter (H) over
the top side of the bottom baseplate (D) in a downward motion
aligning Smove adapter (H) slot to screw tab brace located on the
top side of base plate (D). Once Smove adapter (H) is secure to
Base plate (D) insert #6 athead screw (J) to screw tab brace and
pre drilled hole on right side panel (O) and secure using philips
head screw driver.
Now take Smove holder (C) and align it with the rectangular
insert holes located on the side of smove adapter (H). Push
Smove holder into rectangular insert holes on smove adapter
(H) and slide Smove holder (C) towards the back end of
base plate (D) to lock all hardware into place.
D.
J.
H.
J.
D.
H.
D.
C.

Atatching the hinges (G) to the inside of door panel (P).
Starting from the top of the inside door panel (P) align hinges
(G) to pre milled cup holes and pre drilled screw holes on
inside of door panel (P). After aligning hinge (G) holes to and
cup to Door Panel (P) insert two #6 flathead screws (J) into
predrilled holes on door panel (P) and secure hardware with
philips screwdriver. Repeat these steps for all (4) hinges.
Atatching the strikeplate (I) to the inside of left side panel (M).
align strikeplate (I) to pre drilled screw holes on inside of left
side panel (M). After aligning strikeplate (I)to holes to left side
Panel (M) insert two #6 roundhead screws (K) into predrilled
holes on left side panel (M) and secure hardware with philips
screwdriver.
After installing all of the hardware, start the assembly of the
panels. While having back panel (N) laying on a flat surface
with all inserts faceing up start attaching shelves to Female
inserts on back panel (N). When assembling shelving to back
panel (N) be sure to have ventilation slot located on the edge
of shelf panel faceing the bottom of back panel (N). Ventilla-
tion slot located in image to the left.
Important note: Ventilation slots located on the ends
of shelf panels (Q and R) must be facing towards
bottom of Back Panel (N) for proper installation. Please
refer to diagram for circled location of the ventilation
slot.
Step 9:
Step 7:
Step 8:
G.
J.
J.
I.
K.
K.
N.
P.
M.

Lay back panel (N) on a flat surface with the inserts
facing upwards.
Important note: When fastening compontents (Q) (R)
and (S) to panel (N) be certain that the smooth
unmachined edges are all in the same plain. Be sure
that the edge
Attach top (Q) to panel (N) by pushing the male inserts
in top (Q) into the female inserts in panel (N). Repeat
this exersice for shelf (R) and base (S).
Lay left panel (M) on flat surface with inserts facing
upwards. Use panel assembly installed in Step 10 and
align Male inserts of panels (N, Q, R and S) into female
inserts of left panel (M) and push male inserts into
female inserts connecting the panels.
Step 10:
S.
R.
Q.
N.
With left side panel (M) laying on a flat surface align
female inserts on right side panel (O) to male inserts on
panels (Q, R, S and N) and push female inserts into
female inserts connecting the panels.
N.
R.
Q.
S.
M.
Step 11:
Step 12:
O.
M.
Q.
R.
S.
N.

Connect all 4 Hinges (G) attached to door panel (P) to base
plates (D) attached to Right Side Panel (O). Align each Hinge
(G) arm to center of each Baseplate (D) pushing the two
together until hearing a *CLICK*.
Important note: To detach Hinge (G) from Baseplate
(D) press in release tab. Refer to diagram for circled
location of the release tab.
Step 12: P.
O.
Warranty
The following AAM products are warranted to be free from defects in workmanship and material under
normal usage from the date of purchase for the periods set forth below. (Rust and discoloration to
stainless steel parts resulting from exposure to harsh environmental and/or chemical conditions are
not considered to be defects in workmanship or material and there is no expressed or implied warran-
ty for such condition.
The following toilet partition panels, doors and stiles are warranted against breakage, corrosion,
delaminating and defects in workmanship from the date of purchase for the periods set forth (this
limited warranty is conditioned on the toilet partitions being properly installed, used and serviced).
.
American Architectural Millwork
2825 Commerce Parkway, 34289
North Port, Florida
(844)-307-9571
www.millworkusa.com
D.
G.

Fully Assembled
Single Tier Yu Locker