American Bath Factory Integrated Double Clawfoot User manual

We would like to take this opportunity to thank you for your
purchase of an American Bath Factory Clawfoot Bathtub!
Should you have any questions or comments about your tub,
please email us at [e-mail]
or call at 800-454-BATH (2284) Mon - Fri 7:15 am to 4:00 pm PT
install guide
Integrated Double Clawfoot
1
SPECIFICATIONS
60"
10"
19"
24"
5"
2" Dia.
32"
25"
30"
18"
40"
10¾"
3½"
2"7"
10¾"
Floor Mount Locations for Drain and
Deck Mount Faucet Supply Lines
Overall Dimensions:
Capacity:
Dry Weight:
Full Weight:
60" L x 32" W x 24" H
30 Gallons
100 lbs.
350 lbs.
All measurements are approximate. Dimensions shown
have a tolerance of ±½". Dimensions shown not to scale.

2
BEFORE YOU BEGIN
To ensure that no damage has occurred to your bathtub during
shipping, it is important to check your bathtub for damage prior to
the installation in your home!
DRAIN
Move your new bathtub to a location that will not be damaged. We
recommend that you install the drain onto the bathtub at this time.
Drain
Rubber
Gasket
Escutcheon
Tub Floor
Waste Pipe
(threaded at
upper end)
Floor
Waste
Water Stub
Bathtub
Wall
Overflow
Cover
( INSTALLED)
Adaptor
O-ring
Nut
Silicone
3
Fig. 2 - To Tighten Drain
!! IMPORTANT !!
Your bathtub is a DOUBLE WALL construction. The drain
needs to be installed with SILICONE, not Plumber's Putty!
Apply a liberal amount of "kitchen and bath" type silicone (available
in most Home Improvement or hardware stores) to the drain threads
and a bead on the underside of the Drain Flange (See Fig. 1). Insert the
Drain through the drain hole, screw into the Waste Pipe and verify
that the rubber gasket is seated properly between the bottom of the
tub and the Waste Pipe. The handles of a pair of pliers can help you
screw the Drain securely into the Waste Pipe (See Fig. 2). Wipe off any
excess silicone around the drain with a clean, dry cloth.
Allow 24 hours for the Silicone to cure completely
before adding water to the bathtub.
If everything is sealed and dry, fill your bathtub and check for leaks.
After the water test is complete and there are no leaks, proceed with
installing your bathtub.
Overflow Cover
Floor
Waste Pipe
Tub Floor
Rubber Gasket
Drain Flange
Drain
Fig. 1 - Securing Your Drain

4
Cold Water Supply
INSTALLATION SPECIFICATIONS
Drain Stub
The faucet holes (where the supply lines are placed) are located
2" in from the edge.
The drain is located 10¾" inches in from the edge of the bathtub.
Note: Do not use the measurements for the Deck Mount listed above if
you purchased a Wall Mount or Floor Mount.
A
B
Drain Stub
Hot Water Supply
2"B
Water Supply Lines
CL
Water Supply
Stub
Deck Mount
CL
10¾"
A
5
SECURING YOUR BATHTUB
Failure to secure your bathtub will void your warranty!
It is very important to secure your bathtub to the
floor. This avoids bending or straining the water
supply connections and drain, if the bathtub is
bumped or moved, possibly causing leaks.
The easiest way to secure your tub is to use a
small amount of glue or epoxy directly on the
floor under each foot. You may do this with the
leveling adjuster attached or without. Please see
drawings below.
Aligning your Bathtub
WARNING - Failure to
secure your bathtub may
cause leaks if the bathtub
is moved.
ALIGN & SECURE YOUR BATHTUB
Now that the water test is complete, pay careful attention when
transporting your clawfoot bathtub through a narrow doorway. Tilt
your bathtub on its nose, on to a soft surface (folded towel, sheet,
etc.), and spin it through the doorway. We recommend doing this
instead of disassembling the feet.
Carefully align your bathtub over the water supply stubs and
drain. For deck mount faucets, it may be helpful
to temporarily attach your faucet and water
supply lines to the bathtub, to aid in aligning
the bathtub directly over the water supply stubs.
A B C
Tub Leveler with
Leveling Donut
Washer
Tub Leveler
Floor
Glue
or
Epoxy
Floor Floor
Glue
or
Epoxy
Tub Leveler

6
CLEANING & MAINTAINING YOUR BATHTUB
Your bathtub’s surface is very easy to clean. There are no pores for dirt to
penetrate, so dirt will just rinse off with water. For sanitary purposes, you
should occasionally clean your bathtub with non-abrasive soap and water
when possible. Avoid harsh chemicals. Plain dish-washing detergent such as
JOY®, PALMOLIVE®, IVORY®, etc., is all that isrequired. If you spill something
on the bathtub and need a stronger cleaner, the following are SAFE to use:
GEL GLOSS®, TACKLE®, TOPJOB®, FORMULA 409®, WINDEX®, CLOROX
BLEACH®, GLASS PLUS®,LIQUID COMET®, SOFT SCRUB®, and SPIC & SPAN
POWDER®.
IMPORTANT
DO NOT CLEAN YOUR BATHTUB WITH GOOF OFF®,
SCRUBBING BUBBLES®, LYSOL DISINFECTANT SPRAY®, DOW
DISINFECTANT BATHROOM CLEANER®, PINE-SOL®, WHITE-
CAP®, LESTOIL®, PAINT THINNER, ACETONE, LACQUER
THINNER, M.E.K. or other chemicals that attack the structural
integrity of plastic (including, but not limited to acetones).
Use of these chemicals will destroy the acrylic surface of your tub.
USE OF THESE CHEMICALS WILL VOID YOUR WARRANTY
If you should dull, scratch, or chip your bathtub, the appearance can be
restored to it’s original look. Scratches and dulling can be removed with a
liquid polish such as Gel-Gloss®. Deep scratches or burns can be removed
by using very fine wet sandpaper (600 grit or higher) and finished with a
liquid polish.
(800) 454-BATH Fax [phone]
www.americanbathfactory.com
ABF Integrated Double Clawfoot Install Guide Rev A
n
n
n
n
n
n
n
n
SAFETY INSTRUCTIONS
DANGER! To reduce the risk of injury, do not permit children to use
bathtubs unless they are closely supervised by an adult at all times.
Use this bathtub only for its intended use as described in this manual. Do
not use attachments not recommended by the manufacturer.
Do not attempt to plug in or unplug the electrical devices while in or near
a filled bathtub. Never use or handle electrical devices while in or near a
filled tub.
Never drop or insert any objects into any openings.
Only healthy adults should use the bathtub when the water temperature
is between 100° and 104°F (38°- 40°C). Any temperature below 100°F is
considered safe for longer durations (exceeding 10 - 15 minutes) or for
young children. The water temperature in a bathtub should never exceed
104°F (40°C).
Excessive water temperatures have a high potential for causing fetal
damage during the early months of pregnancy. Pregnant or possibly
pregnant women should limit bathtub temperatures to 38°C (100°F).
The use of alcohol, drugs, or medications before or during bathing may
lead to unconsciousness and the possibility of drowning.
Use of this bathtub may cause drowsiness and changes in heart rate and/
or blood pressure. Persons suffering from obesity, who have a medical
history of heart disease, low or high blood pressure, circulatory problems,
or diabetes should consult a physician before using. Persons using
medications should consult a physician before using this bathtub.
Information in this document is subject to change without notice. Copyright 2018, American Bath Factory. All rights
reserved. Reproduction in any manner whatsoever without the written permission by American Bath Factory is
strictly forbidden. Trademarks and trade names used in this document refer to either the entities claiming the marks
and names or their products. American Bath Factory disclaims any proprietary interest in trademarks and trade
names other than its own.