Oliveri Naples User manual

Manufactured from premium sanitary grade acrylic, Oliveri’s
freestanding baths are easy to install, with self-supporting,
adjustable feet and can be freely located anywhere in your
bathroom.
This manual is designed to provide the correct installation
steps and care advice, for a long-lasting installation.
Correct and proper use of your bath will ensure its
ongoing performance. Please consult the Caring for Your
Bath section below for advice on cleaning and regular
maintenance.
CARING FOR YOUR BATH
Oliveri uses the highest sanitary grade acrylic, however
naked flames, cigarettes or strong chemicals will
damage the bath and must be avoided and/or removed
immediately. To preserve the high gloss acrylic surface:
When filling the bath start with cold water to allow the
bath to gradually adapt to the changing temperature.
After using your bath, clean with a soft cloth and warm
soapy water to clean away any oils or soap, to prevent tide
marks and preserve the high-gloss surface.
Clean using warm soapy water and only mild liquid
detergents. Do not use powders, pastes, creams,
chemicals, window cleaning sprays or abrasive cleaners.
Scratches can be removed with a fine polish like Brasso.
oliveri.com.au
Installation Instructions
Naples
Freestanding Baths
THIS PRODUCT MUST BE INSTALLED BY A QUALIFIED TRADESPERSON
TF151a - Naples Freestanding Bath Installation Instructions Page 1 of 2
PRE-INSTALLATION CHECKS
Inspect the acrylic surface of the bath for
damage. Damage found after installation
is not covered by the manufacturer’s
warranty conditions. ANY CLAIMS FOR
DAMAGE WILL NOT BE ACCEPTED AFTER
INSTALLATION.
Protect your bath before and during
installation. Scratches, cracks or other
surface damage sustained during or after
the installation are NOT COVERED BY
WARRANTY.
Installation must only be carried out by a
QUALIFIED TRADESMAN and in accordance
with building regulations and any local
authority requirements.
STOP AND READ CAREFULLY
• 10 year warranty (see oliveri.com.au for details)
• Manufactured to AS/NZ Standard 2023/1995
• Adjustable self-supporting feet
• Central waste position (plug and waste not included)

INSTALLATION STEPS
WARRANTY TERMS & CONDITIONS - DOMESTIC USE
STEP 1
Remove your freestanding bath from the carton and place it in the
correct position for installation. Check for damage and ensure your
bath does not come in contact with any rough surfaces which may
scratch your bath. Place your freestanding bath on cardboard or
carpet during installation.
STEP 2
Turn the self-leveling feet so the bath base is level and 3 - 5mm
above the finished floor.
IMPORTANT
Installing the bath shell directly onto the bath floor will place
pressure on the outside wall of the bath and can crack the bath.
Ensure there is a gap of 3 - 5mm between the bath shell
and the floor.
Ensure the bath is level so all the water can drain to the
waste outlet.
STEP 3
Carefully tilt the bath on its side and connect it to the drain
outlet. We recommend using a flexible connector. Ensure
the flexible connector is cut to the correct length for easier
installation and to prevent drainage issues.
STEP 4
Before finishing, water test for leaks and correct drainage.
IMPORTANT
Fill the freestanding bath with water and check the water flows
easily to the waste outlet.
NOTE: A small amount of water may pool due to surface
tension.
STEP 5
Apply a thick bead of silicon around the bath base and the
finished floor and allow it to set for 24 hours before use.
3 - 5mm
Waste
Outlet
Drain
Flexible
Connector
FREESTANDING BATH - Acrylic Shell / Steel Frame 10 years replacement product, 1 year labour.
Where a genuine manufacturing defect arises within the warranty period Oliveri will, at its election, repair the defect or replace the product
subject to the terms contained in the full warranty information available at https://oliveri.com.au/service-and-warranty.
This warranty does not cover against normal wear and will be voided if the product is misused or not installed in accordance
with these instructions.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund
for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
SERVICE
If the product requires servicing, please contact your installer (preferably the one who installed it). If the plumber / installer is satisfied that
the problem is not due to poor installation, contact Oliveri’s nominated Warranty Service Agent for assistance on:
Ph: [phone] (choose the after sales service and warranty option)
Email: [email protected]
For full warranty information visit: https://oliveri.com.au/service-and-warranty
If a warranty service call finds that the product does not have a genuine manufacturing fault, our Warranty Service Agent
reserves the right to pass on any call-out fee to the householder.
Oliveri Solutions Pty Ltd. ABN 12 007 551 886 TF151a - Naples Freestanding Bath Installation Instructions Page 2 of 2