American DJ Snap Shit DMX/D User manual

American DJ®LOS ANGELES, CA. 90058 USA - SNAP SHOT DMX/D PG.1
SPECIFICATIONS:
Lamp: ZB-400 100W, Power: 120V 60Hz
Weight: 3 lbs. Size: 7.75” x 7.75” x 8”
Fuse: 10A.
Thank you for purchasing this American DJ®product. For your convenience this
product has been lamped and is ready to be used, there is no assembly required.
Please read the following instructions before installing or using your new unit.
Product Description:
A new revolution in Strobe Lights! The Snap Shot DMX/D™ is a 100W, ultra light weight Strobe Light.
Features include: plastic high tech case design with hanging bracket, and variable speed control (1 - 60 flashes
per second) and dimming capabilities. The Snap Shot DMX/D™can flash different colored light by replacing the
interchangeable lamp cover, Snap/D™; available colors: red, blue, green, & yellow. .
To replace lamp; unscrew front dome of the fixture. Do not touch lamp with bare fingers, oil from fingers will ruin
lamp. Use a clean, dry cloth for replacement. Replace bulbs; reassemble.
For service, contact your American DJ® dealer.
Caution! Always disconnect from main
power before replacing lamps or servicing unit.
Remember to always replace with same lamp
and fuse.
American DJ®User Instructions
Snap Shot DMX/D ™
2345
1
1. Power Switch
2. DMX Addressing or Rate \ Intensity \ Duration
Switches
3.Mode Switches
4.DMX Input
5.DMX Output
PIN 1 GND, PIN2 DATA-, PIN3 DATA +

American DJ®LOS ANGELES, CA. 90058 USA - SNAP SHOT DMX/D PG.2
Stand Alone Mode
1. Disconnect power from strobe then turn off all dipswitches, except for Mode Switch 4.
2. You can program rate; intensity; duration. See the table below.
3. Reconnect power then turn on
Rate Duration
Intensity
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 101 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
on
on
on
on
on
on
on
on
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 101 2 3 4 5 6 7 8 9 10
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
on
on
on
on
on
on
on
on
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 101 2 3 4 5 6 7 8 9 10
Slower
Faster
Dimmer Shorter
Brighter Longer
Operating Instructions
Duty Cycle Because the Snapshot DMX can be used for continuous output (ie while simulat-
ing lightning). It can build up intense heat it and comes with a program to shut down the unit
for a15 second cool down. The Fastest Rate, Brightest Intensity, Longest Duration setting will
cause unit to shut down within 5 seconds. So plan your Show to make sure all units don’t turn
off at same time.

American DJ®LOS ANGELES, CA. 90058 USA - SNAP SHOT DMX/D PG.3
DMX Function DMX Data Assignments
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
on
on
on
on
on
on
on
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
on
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 101 2 3 4 5 6 7 8 9 10
Intensity is first
DMX byte
Intensity is first
DMX byte
Intensity is first
DMX byte
Intensity is first
DMX byte
Intensity is
preset
Intensity is
preset
Intensity is
preset
Duration is
1/2 cycle
Duration is first
DMX byte*
Duration is second
DMX byte*
Duration is
1/2 cycle
Duration is
1/2 cycle
Duration is first
DMX byte*
Duration is second
DMX byte*
Rate is set by DMX
refresh**
Rate is set by DMX
refresh**
Rate is set by DMX
refresh**
Rate is first DMX
byte
Rate is second DMX
byte
Rate is third DMX
byte
Rate is second DMX
byte
Intensity from DMX Values from 0 to 255 are useable
Values from 0-255 are useable Values 0
will flash the lamp for approx. 2 milliseconds,
Duration byte from DMX 255 will flash lamp for 5 seconds on AC 230V
50 Hz supply; On a 120 AC line with ,value 0
will last 3 milliseconds, value 255, 4 seconds.
Values from 0-255 are useable Values 0
will flash the lamp every 4 seconds
Rate byte from DMX on AC 230V 50 Hz supply; On a
120 AC line with Value 0
will flash every 6 seconds.On a 120 AC line
with transformer. The highest rate is 50 or 60
flashes per second
DMX MODE
Using the 1 thru 3 mode dipswitches you can control the intensity, duration, rate by
DMX in 7 different ways with a DMX-512 Board. The following table show how the various
settings these dip switches effect the way the DMX data should be sent.
* By setting duration for a long enough period, latch on is possible
** Performance of Strobes will depend heavily on the intelligence and versatility of the DMX board when
rate is set by the DMX refresh. Higher rates can be achieved if smaller data packets are sent more often.
For modes that use only 1 DMX channel, units should be addressed sequentially
For modes that use 2 DMX channels, units should be addressed at every other address
For modes that use only 3 DMX channel,units should be addressed at every 3rd address
USED WITH
SS-DMX/19C