American Dynamics AD715LS Series Installation and maintenance instructions

Installation and Service Guide
© Sensormatic 2000 (40 pages). DeltaDome II Camera Dome
8000-2708-01, REV. B
1
DeltaDome™II
Programmable
Surveillance Camera
AD716LS and AD715LS Series
Figure 1. SpeedDome Ultra camera dome
American Dynamics, DeltaDome, and the AD logo are
registered trademarks of Sensormatic Electronics Corporation.
Other product names (if any) mentioned herein may be
trademarks or registered trademarks of other companies.
No part of this guide may be reproduced in any form without
written permission from Sensormatic Electronics Corporation.
(c) Copyright 2000. All rights reserved.
MDR 6/00
Contents
About this Guide....................................................1
About the Camera Dome ......................................2
Data Cable Requirements.....................................8
Install/Removal Tool for ADIOB Base...................8
Power-Up Routine.................................................9
Synchronizing Domes ...........................................9
Diagnostic LEDs....................................................9
Warnings and Cautions.......................................10
Indoor Installation................................................12
Using the Install/Removal Tool ...........................20
Troubleshooting Indoor Domes...........................22
Ordering Parts.....................................................34
Specifications-Indoor Dome................................36
Specifications-Outdoor Housing..........................37
Specifications-22X Camera.................................37
Declarations ........................................................38
About this Guide
This guide explains how to connect the camera
dome to a mounting base and how to service it.
It does not explain how to:
•Determine a mounting location for the camera
dome. The mounting location is determined by
customer requirements; therefore, this
information is provided separately.
•Attach the mounting base. There are two types
of mounting bases. See information shipped
with the base.
•Assemble housings and structures used with
this dome. See information shipped with the
housing and structure.
•Program the dome. See operator's guide
shipped with the dome.
Mounting
Base
Housing
Eyeball

INSTALLATION AND SERVICE GUIDE DeltaDome II Camera Dome
8000-2708-01, REV. B
2
About the Camera Dome
The DeltaDome II programmable surveillance
camera (Figure 1) mounts indoors or outdoors,
and can communicate with the video controller
over a SensorNet 485, RS422, or Manchester
network. The dome consists of a mounting base,
and a housing and rotating eyeball assembly.
Mounting Base
The housing and eyeball assembly connects to the
base using a twist and lock action, which enables
the dome to be easily moved from one location to
another. The base attaches directly to a hard or tile
ceiling, or indirectly to walls or ceilings using one of
many optional housings and mounting structures.
As shown in Figure 2, two base types are offered:
an ADUPTB standard base and an ADIOB base
with I/O board.
•ADPTB Base. With this base, video, data, and
power cables are inserted through the base and
attached to the top of the housing and eyeball
assembly, which is then connected to the base.
A lanyard connects between the base and the
housing and eyeball assembly to prevent cables
from being pulled during disassembly.
•ADIOB Base. With this base, video, data, and
power cables are pre-connected to an I/O PC
board. A spring-finger connector on the board
makes electrical contact with the housing and
eyeball assembly as it connects to the base.
Housing and Eyeball Assembly
The housing and eyeball assembly consists
of the following:
•Housing. The housing contains the dome's
power supply, pan motor, and electronics used
to operate the eyeball. The housing provides
one alarm input and one alarm output using the
ADPTB base, or four alarm inputs and four
alarm outputs using the ADIOB base.
•Eyeball. Gloss black and 120mm (4.75") in
diameter, the eyeball contains a camera, tilt
motor, and associated electronics. The eyeball
enables the camera to pan and tilt to track a
target moving in any direction even as it moves
under the dome.
Two slot covers in the eyeball facilitate access
to the camera, one of which incorporates a
camouflaged lens. Remove both covers to
improve ventilation when the dome is to be
used outdoors.
As shown in Table 1, the housing and eyeball
assembly can be ordered:
•With no base for existing indoor installations or
for mounting outdoors.
•With a ADPTB standard base or ADIOB base
with I/O board for new indoor installations.
•With one of four CCD cameras
−Color NTSC
−Black & White EIA
−Color PAL
−Black & White CCIR.
Each camera has 22X optical zoom with cont-
inuous auto focus and back light compensation.
Electronic zoom provides selectable
magnification up to 176X.
Table 1. Product codes for housing and eyeball assembly configurations
Color NTSC B & W EIA Color PAL B & W CCIR
No Base AD716LS AD715LS AD716LS-1 AD715LS-1
RUPTB Base AD716LSP AD715LSP AD716LSP-1 AD715LSP-1
RUIOB Base AD716LSI AD715LSI AD716LSI-1 AD715LSI-1

INSTALLATION AND SERVICE GUIDE DeltaDome II Camera Dome
8000-2708-01, REV. B
3
Figure 2. Mounting base and housing and
eyeball assembly
ADPTB Mounting Base ADIOB Mounting Base
Indoor Ceiling Mounting
Using hardware shipped with the base, the dome
attaches directly to indoor ceilings made of sheet
rock, wood, metal, or concrete (Figure 3), or to tile
ceiling T-bars where they intersect (Figure 4).
Figure 3. Surface mounting to hard ceilings
Figure 4. Surface mounting to tile ceilings

INSTALLATION AND SERVICE GUIDE DeltaDome II Camera Dome
8000-2708-01, REV. B
4
Indoor Ceiling/
Wall Mounting (Optional)
The camera dome attaches to one of the following
optional indoor mounting structures (Figure 5).
Sheet Rock, Plaster or Wood Ceilings
RHIUTH Top hat housing with trim ring
This housing attaches to a ceiling or
to most indoor mounting structures. A
bubble and trim ring provide
concealment. Optional bubbles:
RUCLR (clear), RUSLV (silver),
RUSMK (smoked), or RUGLD (gold).
Plenum adapter RHPLA may be
required to meet local fire codes.
RHIUHC Hard ceiling bracket
Enables top hat housing to be
recessed in ceiling (requires top hat
RHIUTH).
RHIUFB* Fixed bracket
Enables top hat housing to be
recessed in ceiling (requires top hat
RHIUTH).
RHIUPNDT† Pendant mount
Suspends dome from a hard ceiling.
Electrical Box in Ceiling
RHIU3X3† 3 X 3 mounting plate
Attaches dome to a standard
3.5 x 3.5 duplex electrical box.
CAUTION: Do not use the same
electrical box used for line voltage
mains.
RHIU4X4† 4 X 4 mounting plate
Attaches dome to a standard
4 x 4 duplex electrical box.
CAUTION: Do not use the same
electrical box used for line voltage
mains.
Structural I-Beams
RHIUIB† I-beam mount
Enables dome to suspend from an I-
beam.
Tile Ceilings
RHIUFB Fixed bracket
Enables top hat housing to be
recessed in a 2x2 tile (requires
top hat RHIUTH).
RHIUAB Adjustable bracket
Enables top hat housing to be
recessed in a 2x4 tile (requires
top hat RHIUTH).
RHIU2X2* 2 X 2 tile mount
Enables top hat housing to be
recessed in 2x2 openings
(incorporates top hat housing).
RHIU2X2P* 2 X 2 tile pendant mount
Enables dome to be suspended
from 2x2 openings.
Wall Mounting
RHIUWM* Wall mount
Attaches dome to a flat vertical
surface.
RHIUCM* Wall mount with corner feature
Attaches dome to attach to a wall,
inside corner, or outside corner.
RHIULWM*† Long .6m (24") wall mount
Positions dome away from wall to
enable it to see over furniture,
shelving, and displays. This mounting
structure attaches to the wall, inside
corner, or outside corner.
* Option in white, but can be painted to match decor.
† Top hat housing/dome assembly also mounts to structure.

INSTALLATION AND SERVICE GUIDE DeltaDome II Camera Dome
8000-2708-01, REV. B
5
Figure 5. Indoor mounting structures (optional)
RHIUFB
RHIUAB RHIUHC RHIU2X2
RHIUTH
RHIUTR
RUCLR
RUSLV
RUSMK
RUGLD
RHIULWM
RHIUCM
RHIUWM
RHPLA
RHIU3X3
RHIU4X4
RHIUPNDT
RHIUIB
RHIU2X2P

INSTALLATION AND SERVICE GUIDE DeltaDome II Camera Dome
8000-2708-01, REV. B
6
Outdoor Mounting (Optional)
Note: This document does not include outdoor
installation and service instructions. For these
instructions, see Installing the RHODUL Outdoor
Housing, 8000-2573-04.
The camera dome attaches to outdoor walls and
ceilings using an RHODUL outdoor housing
(Figure 6) and one of the following optional
mounting structures (Figure 8):
•RHORM Over Roof Mount
•RHOCM Ceiling Mount
•RHOPM Pole Mount
•RHOWM Wall Mount
•RH170 Corner Bracket.
The outdoor housing contains a pre-installed
mounting base, a cooling fan for hot weather, a
heater for cool weather and to prevent icing, and
surge protection circuitry to protect against
lightning strikes.
An environmental PC board is used to pre-wire
cables. A round spring-finger connector on the
board makes electrical contact with the housing
and eyeball assembly as it connects to the base.
Note: Do not use the I/O board (designed for
indoor use) in place of the environmental board.
Figure 6. ADODH outdoor housing (optional)
SpeedDome Housing Adapter
Bracket (Optional)
An RHSDA adapter bracket (Figure 7) enables the
dome to fit into SpeedDome indoor and outdoor
housings. Locking pins in the bracket enable the
dome to swing out for servicing or removal.
Figure 7. RHSDA adapter bracket (optional)

INSTALLATION AND SERVICE GUIDE DeltaDome II Camera Dome
8000-2708-01, REV. B
7
Figure 8. Outdoor mounting structures
(optional)
RHORM over roof mount
RHOCM ceiling mount
RHOPM pole mount
RHOWM wall mount
RH170 corner bracket (shown with RHOWM mount)
Top View

INSTALLATION AND SERVICE GUIDE DeltaDome II Camera Dome
8000-2708-01, REV. B
8
Data Cable Requirements
Table 2 shows the data cable requirements for
SensorNet, RS422, and Manchester networks. For
more information about communication protocols
and cable networks, see Communication Protocols
and Cable Networks, 8000-2573-19.
Table 2. Data cable requirements
SensorNet RS422 Manchester
Cable
type 1 unshielded,
twisted
pair*
2
shielded,
twisted
pair*
1
shielded
twisted pair**
Wire
gauge 22 AWG 22 AWG 18 AWG
Con
nection Non- polarized Polarized Polarized
Max.
devices
on line
32 10 3
* Power, data, and video cables can be ordered
separately or within a composite cable that can be
ordered in various lengths. Plenum-rated cables
must be used in indoor ceilings used for environ-
mental air return (called "other air space" in the
National Electrical Code). Order parts through
your distribution network.
Note: If you order cable from an outside
source, wire colors may be different.
** Belden 88760 (plenum), or Belden 8760 cable
(non-plenum) cable is recommended. Plenum-
rated cables must be used in indoor ceilings used for
environmental air return (called "other air space" in
the National Electrical Code). Order cable directly
from Belden by calling 1-800-235-3361.
Install/Removal Tool for
RUIOB Base
The install/removal tool (Figure 9) enables you to
connect or disconnect the housing and eyeball
assembly from the RUIOB base with I/O board,
and to attach/detach skirts and bubbles to a top hat
housing, without the need for a ladder. The tool
attaches to a telescopic pole (purchased
separately). See page 20.
CAUTION: Do not use this tool to connect the
dome the RUPTB base.
Figure 9. RHIRT indoor install/removal tool
RHIRT Removal Tool
Teslescopic Pole 08140
by Recreational Water
Products. See page 20
to order.

INSTALLATION AND SERVICE GUIDE DeltaDome II Camera Dome
8000-2708-01, REV. B
9
Power-Up Routine
After power is connected to the dome, the dome
performs the following homing routine.
1. After a few seconds, the camera lens tilts up
into the housing and eyeball assembly.
2. The lens tilts downs until it looks at the floor.
3. Eyeball pans slowly.
4. Lens tilts up 90° (home position).
Once the lens is in its home position, you can
then use the controller to call up the camera
and control it.
Synchronizing Domes
To prevent picture rolling when switching from
camera to camera, all domes can be synchronized
to a 50Hz or 60Hz ac source. A V-phase
adjustment at the control console enables the
dome to sync to any line phase.
Diagnostic LEDs
If ADPTB standard base is used, LEDs in the
housing and eyeball assembly enable you to check
for power and data.
If ADIOB base with I/O board is used, LEDs on the
underside of the mounting base enable you to
check for power and data. If an RS422 network is
used, other LEDs on the board indicate that wiring
is correct, reversed, open, or grounded.

INSTALLATION AND SERVICE GUIDE DeltaDome II Camera Dome
8000-2708-01, REV. B
10
Warnings and Cautions
Please review the following warnings and cautions
before you begin installation or service.
WARNINGS
WARNING!
ALWAYS USE:
•Proper safety equipment for the location and
type of installation.
•Proper lift equipment to reach the installation.
•Safety features of the lift equipment.
BE SURE:
•Electrical power is not connected to the dome
when connecting wires. Dome will move when
power is applied.
•Electrical power is not connected to nearby
fixtures that you might touch during installation.
WARNING! DO NOT install this camera dome in
hazardous areas where highly combustible or
explosive products are stored or used.
WARNING! This dome runs on 24Vac. DO NOT
connect line voltage to this dome.
North America power requirements: In North
America, this device is intended to be supplied
from a Class 2 power supply. For outdoor
installations, use Class 3 wiring techniques, liquid-
tight conduit, or liquid-tight pipe.
This installation should be made by a qualified
service person and should conform to all local
codes.
WARNING!
EU power requirements: This product runs on
24Vac. In the EU, it is intended to be powered from
a Limited Power Source. A limited power source is
a certified source of SELV, and if inherently limited,
with 8 amps maximum output current, and a
maximum of 100VA available; or if not inherently
limited, fused with a maximum value of 3.3 Amps,
meeting section 2.11 of IEC950, and a maximum of
250VA available. The power supply can be
obtained through Sensormatic or through another
source where the provider can furnish the
verification. This is required to assure electrical
safety in the product.
Stromanforderungen in der EU: Dieses Produkt
wird mit 24 V Wechselstrom betrieben. In der EU
ist es für den Betrieb durch eine begrenzte
Stromquelle vorgesehen. Eine begrenzte
Stromquelle ist eine zertifizierte SELV-Quelle
(Schutzkleinspannung), bei inhärenter Begrenzung
mit einem maximalen Ausgangsstrom von 8 A und
100 VA maximaler Verfügbarkeit, bei nicht
inhärenter Begrenzung mit einer maximalen
Sicherung von 3,3 A gemäß Abschnitt 2.11 der
IEC950 und 250 VA maximaler Verfügbarkeit. Das
Netzteil kann über Sensormatic oder eine andere
Quelle bezogen werden, wobei der Anbieter den
Nachweis der Konformität bereitstellen sollte. Dies
ist zur Gewährleistung der elektrischen Sicherheit
des Produktes erforderlich.