AMERICANA 25 Operating instructions

197D7215P003 49-60502 01-07 JR
Safety Information
Connect Electricity . . . . . . . . . . . . .3
Extension Cords . . . . . . . . . . . . . . .2
Proper Disposal . . . . . . . . . . . . . . . .2
Safety Precautions . . . . . . . . . . . . . .2
Operating Instructions
Automatic Icemaker . . . . . . . . . . . .7
Care and Cleaning . . . . . . . . . . .9, 10
Controls . . . . . . . . . . . . . . . . . . . . .4
Crispers . . . . . . . . . . . . . . . . . . . . . .6
Dispenser . . . . . . . . . . . . . . . . . . . . .8
Replacing the Light Bulbs . . . . . . .11
Shelves and Bins . . . . . . . . . . . . . . .5
Installation Instructions
Preparing to Install
the Refrigerator . . . . . . . . . . . . . . .12
Water Line Installation . . . . . .13–17
Troubleshooting Tips
Before You Call For Service . . .18–20
Normal Operating Sounds . . . . . .18
Consumer Support
Consumer Support . . . . . . . . . . . .24
Product Registration . . . . . . . .21, 22
Warranty . . . . . . . . . . . . . . . . . . . .23
Write the model and serial
numbers here:
Model # __________________
Serial # __________________
Find these numbers on a label inside
the refrigerator compartment at the
top on the right side behind the
controls.
Refrigerators
Owner’s Manual and Installation Instructions
Model 25
Printed in the United States
Printed on Recycled Paper
Side by Side
www.AmericanaAppliances.com

PROPER DISPOSAL OF THE REFRIGERATOR
Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are
still dangerous…even if they will sit for “just a few
days.” If you are getting rid of your old refrigerator,
please follow the instructions below to help prevent
accidents.
Before You Throw Away Your Old Refrigerator
or Freezer:
■Take off the doors.
■Leave the shelves in place so that children may
not easily climb inside.
Refrigerants
All refrigeration products contain refrigerants,
which under federal law must be removed prior
to product disposal. If you are getting rid of an
old refrigeration product, check with the company
handling the disposal about what to do.
USE OF EXTENSION CORDS
Because of potential safety hazards under certain conditions, we strongly recommend
against the use of an extension cord.
However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United
States) or a CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a grounding
type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.
DANGER! RISK OF CHILD ENTRAPMENT
Consumer Support Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions
2
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
Use this appliance only for its intended purpose as described in this Owner’s Manual.
SAFETY PRECAUTIONS
When using electrical appliances, basic safety precautions should be followed, including the following:
■
■This refrigerator must be properly installed
and located in accordance with the Installation
Instructions before it is used.
■
■Do not allow children to climb, stand or hang
on the shelves in the refrigerator. They could
damage the refrigerator and seriously injure
themselves.
■
■Do not touch the cold surfaces in the freezer
compartment when hands are damp or wet. Skin
may stick to these extremely cold surfaces.
■
■Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
■
■In refrigerators with automatic icemakers,
avoid contact with the moving parts of the
ejector mechanism, or with the heating element
that releases the cubes. Do not place fingers or
hands on the automatic icemaking mechanism
while the refrigerator is plugged in.
■
■Keep fingers out of the “pinch point” areas;
clearances between the doors and between
the doors and cabinet are necessarily small.
Be careful closing doors when children are
in the area.
■
■Unplug the refrigerator before cleaning and
making repairs.
NOTE: We strongly recommend that any servicing be
performed by a qualified individual.
■
■Do not refreeze frozen foods which have thawed
completely.
NOTE: Turning the refrigerator off via the controls on
the touch panel does not shut off electrical power to the
refrigerator.

Consumer Support
Troubleshooting TipsOperating Instructions
Safety Instructions Installation Instructions
3
www.AmericanaAppliances.com
WARNING!
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For
personal safety, this appliance must be properly grounded.
The power cord of this appliance is equipped with
a 3-prong (grounding) plug which mates with a
standard 3-prong (grounding) wall outlet to
minimize the possibility of electric shock hazard
from this appliance.
Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
properly grounded.
If the outlet is a standard 2-prong outlet, it is your
personal responsibility and obligation to have it
replaced with a properly grounded 3-prong wall
outlet.
The refrigerator should always be plugged into its
own individual electrical outlet which has a voltage
rating that matches the rating plate.
This provides the best performance and also
prevents overloading house wiring circuits which
could cause a fire hazard from overheated wires.
Never unplug your refrigerator by pulling on the
power cord. Always grip plug firmly and pull
straight out from the outlet.
Repair or replace immediately all power cords that
have become frayed or otherwise damaged. Do not
use a cord that shows cracks or abrasion damage
along its length or at either end.
When moving the refrigerator away from the
wall, be careful not to roll over or damage the
power cord.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS

4
About the controls on the refrigerator.
Startup Steps for Proper Temperature Control
STEP 1—Set Fresh Food Control on “5.”
STEP 2—Set Freezer Control on “5.”
STEP 3—WAIT 12 HOURS for temperature to stabilize.
STEP 4—If a change is needed, move the control one number at a time and allow 12 hours
for temperature to stabilize.
■On some models, setting both controls to the warmest setting until the display
flashes (off) will stop cooling in both the freezer and refrigerator compartments.
■On other models, setting either control to the warmest setting until the display
flashes (off) will stop the cooling to the freezer and refrigerator.
NOTE: Turning the refrigerator to the 0 (off) setting via the controls does not
shut off electrical power to the refrigerator.
Control settings will vary based on personal preferences, usage and
operating conditions and may require more than one adjustment.
Consumer Support Troubleshooting Tips Installation Instructions Safety InstructionsOperating Instructions

Consumer Support
Troubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions
Rearranging the Shelves
To Remove
To Replace
Deep Door Shelves
Detachable shelf extenders deepen and
enclose fixed door shelves, providing
more storage room and greater storage
flexibility.
To remove: Lift the shelf extender straight
up, then pull out.
To replace: Engage the shelf extender in the
molded supports on the door and push in.
It will lock in place.
About the shelves and bins. www.AmericanaAppliances.com
Bins on the Fresh Food Compartment Door
Adjustable bins can easily be carried from
refrigerator to work area.
To remove: Lift the front of the bin up,
then pull out.
To replace or relocate: Engage the bin in the
molded supports of the door, and push in.
Bin will lock in place.
Refrigerator Shelves: Freezer Shelves:
Lift up and out Tilt up
Insert
top hook
Lower to
lock in place
To Remove
Not all features are on all models.
5

When replacing the crispers,
make sure you slide them through
the crisper guides.
Crisper
Guides
Consumer Support Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions
6
About the crispers.
Not all features are on all models.
Fruit and Vegetable Crispers
Excess water that may accumulate in the
bottom of the drawers should be wiped dry.
About the crisper removal.
Not all features are on all models.
Crisper Removal
Crispers can easily be removed by tilting up
slightly and pulling past stop location. If the door prevents you from taking out the crispers, the refrigerator will need to
be rolled forward until the door opens
enough to slide the crispers out. In some
cases, when you roll the refrigerator out,
you will need to move the refrigerator to
the left as you roll it out.

Consumer Support
Troubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions
Ice Storage Drawer
Icemaker Accessory Kit
To access ice, pull the drawer out.
To remove the drawer, pull it straight out
and lift it past the stop location.
If your refrigerator did not come already
equipped with an automatic icemaker,
an icemaker accessory kit is available at
extra cost.
Check the back of the refrigerator for
the specific icemaker kit needed for
your model.
7
Icemaker
Feeler Arm
Power
Switch
Green
Power Light
About the automatic icemaker. www.AmericanaAppliances.com
A newly-installed refrigerator may take 12–24 hours to begin making ice.
Automatic Icemaker (on some models)
The icemaker will produce seven cubes
per cycle—approximately 100–130 cubes
in a 24-hour period, depending on freezer
compartment temperature, room
temperature, number of door openings
and other use conditions.
If the refrigerator is operated before the
water connection is made to the icemaker,
set the power switch in the O (off) position.
When the refrigerator has been connected
to the water supply, set the power switch to
the I (on) position.
The icemaker will fill with water when
it cools to 15°F. A newly-installed
refrigerator may take 12–24 hours to
begin making ice cubes.
Throw away the first few batches of ice to
allow the water line to clear.
Be sure nothing interferes with the sweep
of the feeler arm.
It is normal for several cubes to be joined
together.
If ice is not used frequently, old ice cubes
will become cloudy, taste stale, and shrink.
If ice cubes get stuck in the icemaker, the
green power light will blink. To correct this,
set the power switch to 0 (off) and remove
the cubes. Set the power switch to I (on) to
restart the icemaker. After the icemaker has
been turned on again, there will be a delay
of about 45 minutes before the icemaker
resumes operation.
NOTE: In homes with lower-than-average water
pressure, you may hear the icemaker cycle multiple
times when making one batch of ice.
There is an upper freezer shelf
above the icemaker that can be
used for storage.

Some dispenser models offer water only. On
other models you can select CUBED ICE
or WATER .
Press the glass gently against the top of the
dispenser cradle.
If no water is dispensed when the refrigerator is
first installed, there may be air in the water line
system. Press the dispenser arm for at least two
minutes to remove trapped air from the water line
and to fill the water system. To flush out impurities
in the water line, throw away the first six glassfuls
of water.
CAUTION: Never put fingers or any other
objects into the ice crusher discharge opening.
Locking the Dispenser (on some models)
Press the Lock pad for
3 seconds to lock the
dispenser and control
panel. To unlock, press
and hold the pad again
for 3 seconds.
Dispenser Light (on some models)
This pad turns the night
light in the dispenser on
and off. The light also
comes on when the
dispenser cradle is
pressed. If this light
burns out, it should be replaced with a
6 watt maximum, 12 volt DC bulb.
8
Consumer Support Troubleshooting Tips Installation Instructions Safety InstructionsOperating Instructions
About the dispenser.
On some models
Ice Storage Drawer
on Ice Dispenser Models
To remove:
Set the icemaker power switch to the O (off)
position. Pull the drawer straight out and
then lift past the stop position.
To replace:
When replacing the drawer, make sure to
push it firmly into place. If it does not go all
the way back, remove it and rotate the drive
mechanism 1/4 turn. Then push the
drawer back again.
Important Facts About Your Ice Dispenser
■Do not add ice from trays or bags to
the storage bin. It may not crush or
dispense well.
■Avoid overfilling glass with ice and use
of narrow glasses. Backed-up ice can jam
the chute or cause the door in the chute
to freeze shut. If ice is blocking the
chute, poke it through with a wooden
spoon.
■Beverages and foods should not be
quick-chilled in the ice storage bin.
Cans, bottles or food packages in the
storage bin may cause the icemaker
or auger to jam.
■To keep dispensed ice from missing
the glass, put the glass close to, but
not touching, the dispenser opening.
■The first glass of water dispensed may be
warmer than the following ones. This is
normal.
■Dispensed water is not ice cold.
For colder water, simply add ice cubes
before dispensing water.
To Use the Dispenser
Drive
Mechanism
Rotate

Consumer Support
Troubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions
Care and cleaning of the refrigerator. www.AmericanaAppliances.com
Cleaning the Outside
The dispenser drip area, (on some models)
beneath the grille, should be wiped dry. Water
left in this area may leave deposits. Remove
the deposits by adding undiluted vinegar to
the well. Soak until the deposits disappear
or become loose enough to rinse away.
The dispenser cradle (on some models).
Before cleaning, lock the dispenser by
pressing and holding the Lock pad for
3 seconds. Clean with warm water and
baking soda solution—about a tablespoon
(15 ml) of baking soda to a quart (1 liter)
of water. Rinse thoroughly and wipe dry.
The door handles and trim. Clean with a
cloth dampened with soapy water. Dry
with a soft cloth.
Keep the outside clean. Wipe with a clean
cloth lightly dampened with kitchen
appliance wax or mild liquid dish detergent.
Dry and polish with a clean, soft cloth.
Do not wipe the refrigerator with a soiled dish
cloth or wet towel. These may leave a residue
that can erode the paint. Do not use scouring
pads, powdered cleaners, bleach or cleaners
containing bleach because these products can
scratch and weaken the paint finish.
Cleaning the Inside
To help prevent odors, leave an open box of
baking soda in the fresh food and freezer
compartments.
Unplug the refrigerator before cleaning. If this
is not practical, wring excess moisture out
of sponge or cloth when cleaning around
switches, lights or controls.
Use warm water and baking soda solution—
about a tablespoon (15 ml) of baking soda
to a quart (1 liter) of water. This both
cleans and neutralizes odors. Rinse and
wipe dry.
After cleaning the door gaskets, apply a thin
layer of petroleum jelly to the door gaskets
at the hinge side. This helps keep the
gaskets from sticking and bending out
of shape.
Drain opening in freezer compartment. During
yearly cleaning, remove bottom freezer
basket and flush a solution of baking
soda—1 teaspoon (5 ml) and 2 cups
(500 ml) of hot (not boiling) water—
through the drain line with the help of a
meat baster. This will help eliminate odor
and reduce the likelihood of a clogged
drain line. If drain becomes clogged, use a
meat baster and baking soda solution to
force the clog through the drain line.
Avoid cleaning cold glass shelves with hot water
because the extreme temperature difference
may cause them to break. Handle glass shelves
carefully. Bumping tempered glass can cause it
to shatter.
Do not wash any plastic refrigerator parts in
the dishwasher.
9

For long vacations or absences, remove
food and unplug the refrigerator. Clean
the interior with a baking soda solution
of one tablespoon (15 ml) of baking soda
to one quart (1 liter) of water. Leave the
doors open.
Set the icemaker power switch to the O (off)
position and shut off the water supply to
the refrigerator.
If the temperature can drop below
freezing, have a qualified servicer drain the
water supply system (on some models) to
prevent serious property damage due to
flooding.
10
Consumer Support Troubleshooting Tips Installation Instructions Safety InstructionsOperating Instructions
Care and cleaning of the refrigerator.
Behind the Refrigerator
Be careful when moving the refrigerator
away from the wall. All types of floor
coverings can be damaged, particularly
cushioned coverings and those with
embossed surfaces.
Pull the refrigerator straight out and return
it to position by pushing it straight in.
Moving the refrigerator in a side direction
may result in damage to the floor covering
or refrigerator.
When pushing the refrigerator back, make sure
you don’t roll over the power cord or icemaker
supply line (on some models).
Preparing for Vacation
Preparing to Move
Secure all loose items such as grille,
shelves and drawers by taping them
securely in place to prevent damage.
Be sure the refrigerator stays in an upright
position during moving.

Consumer Support
Troubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions
Replacing the light bulbs. www.AmericanaAppliances.com
NOTE: Turning the refrigerator to the 0 (off) setting via the controls does not shut off electrical power to the refrigerator.
Fresh Food Compartment—Upper Light
Unplug the refrigerator.
On models with pad controls—The
bulb is located near the upper-left rear
corner of the compartment, behind the
light shield.
A) Remove the light shield by
sliding it forward and out of the
compartment.
B) Replace with an appliance bulb of
the same or lower wattage.
C) Replace the light shield by holding
it against the left wall and sliding up
and toward the rear wall until it
snaps in place.
On models with knob controls—The
bulb is located behind the controls.
Replace with an appliance bulb of
the same or lower wattage.
Plug the refrigerator back in.
Freezer Compartment
Unplug the refrigerator.
Remove the shelf just below light
shield. (The shelf will be easier to
remove if it is emptied first.)
Lift up on the light shield to remove.
After replacing with an appliance
bulb of the same or lower wattage,
reinstall the shield by hanging it
from the three tabs.
Reinstall the shelf and plug the
refrigerator back in.
11
Dispenser (on some models)
Unplug the refrigerator.
The bulb is located on the dispenser
under the control panel. Remove
the light bulb by turning it
counterclockwise.
Replace the bulb with a bulb of the
same size and wattage.
Plug the refrigerator back in.

BEFORE YOU BEGIN
Read these instructions completely and carefully.
•IMPORTANT –Save these instructions for
local inspector’s use.
•IMPORTANT –Observe all governing codes
and ordinances.
•Note to Installer –Be sure to leave these instructions
with the Consumer.
•Note to Consumer –Keep these instructions for future
reference.
•Skill level – Installation of this appliance requires basic
mechanical skills.
•Completion time – Refrigerator Installation
15 minutes
•Proper installation is the responsibility of the installer.
•Product failure due to improper installation is not covered
under the Warranty.
• Do not install the refrigerator where the temperature will go
below 60°F (16°C) because it will not run often enough to
maintain proper temperatures.
• Install it on a floor strong enough to support it fully loaded.
REFRIGERATOR LOCATION
Installation Refrigerator
Instructions Model 25
Allow the following clearances for ease of installation, proper air
circulation and plumbing and electrical connections.
• Sides 1/8″ (4 mm)
• Top 1″ (25 mm)
• Back 1″ (25 mm)
A door clearance of 3/4″(19 mm) is needed for a 90° door
opening which provides better access to the food storage area.
CLEARANCES
The rollers have 3 purposes:
■Rollers adjust so the door closes easily when opened about
halfway.
■Rollers adjust so the refrigerator is firmly positioned on the
floor and does not wobble.
■Rollers allow you to move the refrigerator away from the wall
for cleaning.
To adjust the rollers:
Turn the roller adjusting screws
clockwise to raise the refrigerator,
counterclockwise to lower it. Use an
adjustable wrench (3/8″hex head bolt) or pliers.
ROLLERS
If the refrigerator has an icemaker, it will have to be connected
to a cold water line. A GE water supply kit (containing tubing,
shutoff valve, fittings and instructions) is available at extra cost
from your dealer or from Parts and Accessories, 800.626.2002.
WATER SUPPLY TO THE ICEMAKER
(on some models)
If you have questions, call 1.800.432.2737
DOOR ALIGNMENT
After leveling, make sure that the doors are even at the top.
To make the doors even, adjust the refrigerator door as follows:
Remove the Base Grille, open the doors, then pull the grille
straight out.
Determine which of the two doors is higher than the other.
Lift the lower door, along with the small cam.
Place the shim between the Door Metal Hinge and the small
cam as shown.
Press in the shim so that it fits in between the metal hinge
and the plastic cam.
Close the doors and check if they are level at the top. If one
door is still lower than the other, repeat the process and
insert another shim.
NOTE: If the doors are not even and the shim is already inserted,
you can remove the shim to lower the door.
Shim
Shims are stored
under the fresh food
door top hinge cover.
12

Installation Instructions
13
INSTALLING THE WATER LINE
Recommended copper water supply kits are WX8X2,
WX8X3 or WX8X4, depending on the amount of
tubing you need. Approved plastic water supply
lines are GE SmartConnect™ Refrigerator Tubing
(WX08X10002, WX08X10006, WX08X10015 and
WX08X10025).
When connecting your refrigerator to a GE Reverse
Osmosis Water System, the only approved installation
is with a GE RVKit. For other reverse osmosis water
systems, follow the manufacturer’s recommendations.
This water line installation is not warranted by the
refrigerator or icemaker manufacturer. Follow these
instructions carefully to minimize the risk of expensive
water damage.
Water hammer (water banging in the pipes) in house
plumbing can cause damage to refrigerator parts and
lead to water leakage or flooding. Call a qualified
plumber to correct water hammer before installing
the water supply line to the refrigerator.
To prevent burns and product damage, do not hook
up the water line to the hot water line.
If you use your refrigerator before connecting the
water line, make sure the icemaker power switch is in
the O (off) position.
Do not install the icemaker tubing in areas where
temperatures fall below freezing.
When using any electrical device (such as a power
drill) during installation, be sure the device is double
insulated or grounded in a manner to prevent the
hazard of electric shock, or is battery powered.
All installations must be in accordance with local
plumbing code requirements.
BEFORE YOU BEGIN
•Copper or GE SmartConnect™ Refrigerator Tubing
kit, 1/4″outer diameter to connect the refrigerator
to the water supply. If using copper, be sure both ends
of the tubing are cut square.
To determine how much tubing you need: measure
the distance from the water valve on the back of the
refrigerator to the water supply pipe. Be sure there is
sufficient extra tubing to allow the refrigerator to move
out from the wall after installation.
GE SmartConnect™ Refrigerator Tubing Kits are
available in the following lengths:
2′ (.6 m) – WX08X10002
6′ (1.8 m) – WX08X10006
15′ (4.6 m) – WX08X10015
25′ (7.6 m) – WX08X10025
NOTE: The only GE approved plastic tubing is that
supplied in GE SmartConnect™ Refrigerator Tubing
kits. Do not use any other plastic water supply line
because the line is under pressure at all times. Certain
types of plastic will crack or rupture with age and cause
water damage to your home.
WHAT YOU WILL NEED

Installation Instructions
INSTALLING THE WATER LINE
SHUT OFF THE MAIN WATER
SUPPLY
Turn on the nearest faucet long enough to clear
the line of water.
Install the shutoff valve on the nearest frequently used
drinking water line.
1
Choose a location for the valve that is easily
accessible. It is best to connect into the side of a
vertical water pipe. When it is necessary to connect
into a horizontal water pipe, make the connection
to the top or side, rather than at the bottom,
to avoid drawing off any sediment from the
water pipe.
CHOOSE THE VALVE LOCATION
2
Drill a 1/4″hole in the water pipe (even if using a
self-piercing valve) using a sharp bit. Remove any
burrs resulting from drilling the hole in the pipe.
Take care not to allow water to drain into the drill.
Failure to drill a 1/4″hole may result in reduced
ice production or smaller cubes.
DRILL THE HOLE FOR THE VALVE
3
•A GE water supply kit (containing tubing, shutoff
valve and fittings listed below) is available at extra
cost from your dealer or from Parts and Accessories,
800.626.2002.
•A cold water supply. The water pressure must be
between 20 and 120 p.s.i. (1.4–8.2 bar).
•Power drill.
•1/2″or adjustable wrench.
•Straight and Phillips blade screwdriver.
•Two 1/4″outer diameter compression nuts and
2 ferrules (sleeves)—to connect the copper tubing
to the shutoff valve and the refrigerator
water valve.
OR
•If you are using a GE SmartConnect™ Refrigerator
Tubing kit, the necessary fittings are preassembled to
the tubing.
•If your existing copper water line has a flared fitting
at the end, you will need an adapter (available at
plumbing supply stores) to connect the water line to
the refrigerator OR you can cut off the flared fitting
with a tube cutter and then use a compression fitting.
Do not cut formed end from GE SmartConnect™
Refrigerator tubing.
•Shutoff valve to connect to the cold water line.
The shutoff valve should have a water inlet with a
minimum inside diameter of 5/32″at the point of
connection to the COLD WATER LINE. Saddle-type
shutoff valves are included in many water supply kits.
Before purchasing, make sure a saddle-type valve
complies with your local plumbing codes.
WHAT YOU WILL NEED (CONT.)
14

Installation Instructions
15
Place the compression nut and ferrule (sleeve) for
copper tubing onto the end of the tubing and
connect it to the shutoff valve.
Make sure the tubing is fully inserted into the valve.
Tighten the compression nut securely.
For plastic tubing from a GE SmartConnect™
Refrigerator Tubing kit, insert the molded end
of the tubing into the shutoff valve and tighten
compression nut until it is hand tight, then tighten
one additional turn with a wrench. Overtightening
may cause leaks.
CONNECT THE TUBING TO THE
VALVE
7
Turn the main water supply on and flush out the
tubing until the water is clear.
Shut the water off at the water valve after about
one quart (1 liter) of water has been flushed
through the tubing.
FLUSH OUT THE TUBING
8
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.
Saddle-Type
Shutoff Valve
Compression Nut
SmartConnect™
Tubing
Packing Nut
Outlet Valve Ferrule (sleeve)
Fasten the shutoff valve to the cold water pipe with
the pipe clamp.
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.
FASTEN THE SHUTOFF VALVE
4
Tighten the clamp screws until the sealing washer
begins to swell.
NOTE: Do not overtighten or you may crush the
tubing.
TIGHTEN THE PIPE CLAMP
5
Vertical Cold
Water Pipe
Saddle-Type
Shutoff Valve
Washer
Inlet End
Pipe Clamp
Clamp Screw
Route the tubing between the cold water line and
the refrigerator.
Route the tubing through a hole drilled in the wall
or floor (behind the refrigerator or adjacent base
cabinet) as close to the wall as possible.
NOTE: Be sure there is sufficient extra tubing to
allow the refrigerator to move out from the wall
after installation.
ROUTE THE TUBING
6
Pipe Clamp

Installation Instructions
INSTALLING THE WATER LINE (cont.)
Tighten any connections that leak.
TURN THE WATER ON AT THE
SHUTOFF VALVE
10
Place the compression nut and ferrule (sleeve)
onto the end of the tubing as shown. On a GE
SmartConnect Refrigerator Tubing kit, the nuts
are already assembled to the tubing.
On models using the refrigeration connection at
the water valve, remove the plastic flexible cap.
NOTES:
•Before making the connection to the refrigerator,
be sure the refrigerator power cord is not
plugged into the wall outlet.
•If your refrigerator does not have a water filter,
we recommend installing one if your water supply
has sand or particles that could clog the screen of
the refrigerator’s water valve. Install it in the
water line near the refrigerator. If using a GE
SmartConnect™ Refrigerator Tubing kit, you
will need an additional tube (WX08X10002)
to connect the filter. Do not cut plastic tube
to install filter.
CONNECT THE TUBING TO THE
REFRIGERATOR
9CONNECT THE TUBING TO THE
REFRIGERATOR (CONT.)
9
Some models have the refrigerator connection at
the end of tubing located outside the compressor
compartment access cover. On other models, the
compressor compartment access cover must be
removed in order to access the refrigerator
connection at the water valve.
Reattach the access cover.
Insert the end of the tubing into the refrigerator
connection as far as possible. While holding the
tubing, tighten the fitting.
For plastic tubing from a GE SmartConnect
Refrigerator Tubing kit, insert the molded end of
the tubing into the refrigerator connection and
tighten the compression nut until it is hand tight,
then tighten one additional turn with a wrench.
Overtightening may cause leaks.
Fasten the tubing into the clamp provided as
shown to keep it in position. You may need to pry
open the clamp.
One of the illustrations below will look like the
connection on your refrigerator.
1/4″
Compression
Nut
Tubing
Clamp 1/4″
Tubing
Refrigerator
Connection
SmartConnect™
Tubing
Ferrule
(sleeve)
Tubing
Clamp
Refrigerator
Connection
SmartConnect™
Tubing
1/4″
Compression
Nut
Ferrule
(sleeve)
1/4″
Tubing
16

Installation Instructions
17
Arrange the coil of tubing so that it does not vibrate
against the back of the refrigerator or against the
wall. Push the refrigerator back to the wall.
PLUG IN THE REFRIGERATOR
11 START THE ICEMAKER
Set the icemaker power switch to the I (on) position.
The icemaker will not begin to operate until it
reaches its operating temperature of 15°F (-9°C)
or below. It will then begin operation automatically
if the icemaker power switch is in the I (on) position.
NOTE: In lower water pressure conditions, the
water valve may turn on up to 3 times to deliver
enough water to the icemaker.

Consumer Support Troubleshooting Tips Installation Instructions Safety InstructionsOperating Instructions
Normal operating sounds.
The new high efficiency compressor runs faster and will have a higher pitch hum
or pulsating sound while operating.
The fan circulating air inside the freezer which keeps the temperatures
throughout.
Water dropping on the defrost heater causing a sizzling, hissing or popping
sound during the defrost cycle.
The flow of refrigerant through the freezer cooling coils sounds like boiling
water or a gurgling noise.
Cracking or popping of cooling coils caused by expansion and contraction
during defrost and refrigeration following defrost.
Water dripping as it melts from the evaporator and flows to the drain pan
during the defrost cycle.
Icemaker (on some models)
The icemaker water valve will buzz when the icemaker fills with water. If the
power switch is in the I (on) position, it will buzz even if it has not yet been hooked
up to water. Keeping the power switch in the I (on) position before it is hooked
up to water can damage the icemaker. To prevent this, set the power switch to the
O (off) position. This will stop the buzzing.
The sound of cubes dropping into the bin and water running in pipes as
icemaker refills.
Before you call for service…
Troubleshooting Tips
Save time and money! Review the charts on the following
pages first and you may not need to call for service.
Problem Possible Causes What To Do
Refrigerator does not Refrigerator in defrost cycle. •Wait about 30 minutes for defrost cycle to end.
operate Freezer control •Move the freezer control to a lower temperature setting.
in 0 (off) position.
Refrigerator is unplugged. •Push the plug completely into the outlet.
The fuse is blown/circuit •Replace fuse or reset the breaker.
breaker is tripped.
Vibration or rattling Front rollers need adjusting. •See Rollers.
(slight vibration
is normal)
These sounds are normal
and are due mostly to highly
efficient operation.
18

Consumer Support
Troubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions
www.AmericanaAppliances.com
Problem Possible Causes What To Do
Motor operates for Normal when refrigerator •Wait 24 hours for the refrigerator to completely
long periods or cycles is first plugged in. cool down.
on and off frequently. Often occurs when large •This is normal.
(Modern refrigerators amounts of food are
with more storage placed in refrigerator.
space and a larger
Door left open. •Check to see if package is holding door open.
freezer require more
Hot weather or frequent •This is normal.
operating time. They
door openings.
start and stop often
Temperature controls •See About the controls.
to maintain even
set at the coldest
temperatures.)
setting.
Fresh food or freezer Temperature control not set •See About the controls.
compartment too warm cold enough.
Warm weather or frequent •Set the temperature control one step colder.
door openings. See About the controls.
Door left open. •Check to see if package is holding door open.
Frost or ice crystals Door left open. •Check to see if package is holding door open.
on frozen food Too frequent or too long
(frost within package door openings.
is normal)
Divider between fresh Automatic energy saver •This helps prevent condensation on the outside.
food and freezer system circulates warm
compartments liquid around front edge
feels warm of freezer compartment.
Automatic icemaker Icemaker power switch •Set the power switch to the I (on) position.
does not work is in the O (off) position.
(on some models) Water supply turned off or •See Installing the water line.
not connected.
Freezer compartment •Wait 24 hours for the refrigerator to completely
too warm. cool down.
Piled up cubes in the storage •Level cubes by hand.
bin cause the icemaker
to shut off.
Ice cubes stuck in icemaker. •Turn off the icemaker, remove cubes, and turn the
(Green power light on icemaker back on.
icemaker blinking).
Ice cubes have Ice storage bin needs cleaning. •Empty and wash bin. Discard old cubes.
odor/taste Food transmitting odor/taste •Wrap foods well.
to ice cubes.
Interior of refrigerator •See Care and cleaning.
needs cleaning.
Slow ice cube freezing Door left open. •Check to see if package is holding door open.
Temperature control not set •See About the controls.
cold enough.
Door not closing Door gasket on hinge side •Apply petroleum jelly on face of gasket.
properly sticking or folding over.
Orange glow in Defrost heater is on. •This is normal.
the freezer
19

Problem Possible Causes What To Do
Cube dispenser does not Icemaker turned off or •Turn on icemaker or water supply.
work (on some models) water supply turned off.
Ice cubes are frozen to •Remove cubes.
icemaker feeler arm.
Irregular ice clumps in •Break up with fingertip pressure and discard
storage container. remaining clumps.
•Freezer may be too warm. Adjust the freezer control
to a colder setting, one position at a time, until clumps
do not form.
Dispenser is LOCKED.•Press and hold the Lock pad for 3 seconds.
Water has poor taste/odor Water dispenser has not been •Dispense water until all water in system is replenished.
(on some models) used for a long time.
Water dispenser does Water supply line turned •See Installing the water line.
not work (on some models) off or not connected.
Air may be trapped in the •Press the dispenser arm for at least two minutes.
water system.
Dispenser is LOCKED.•Press and hold the Lock pad for 3 seconds.
No water or ice cube Supply line or shutoff •Call a plumber.
production valve is clogged.
Dispenser is LOCKED.•Press and hold the Lock pad for 3 seconds.
Refrigerator has odor Foods transmitting •Foods with strong odors should be tightly wrapped.
odor to refrigerator. •Keep an open box of baking soda in the refrigerator;
replace every three months.
Interior needs cleaning. •See Care and cleaning.
Defrost water drainage •See Care and cleaning.
system needs cleaning.
Moisture forms on Not unusual during •Wipe surface dry.
outside of refrigerator periods of high humidity.
Moisture collects inside Too frequent or too
(in humid weather, air long door openings.
carries moisture into
refrigerator when doors
are opened)
Interior light does No power at outlet. •Replace fuse or reset the breaker.
not work Light bulb burned out. •See Replacing the light bulbs.
Water on kitchen floor or Drain in the bottom of •See Care and cleaning.
on bottom of freezer the freezer clogged.
Cubes jammed in chute. •Poke ice through with a wooden spoon.
Hot air from bottom Normal air flow cooling motor.
of refrigerator In the refrigeration process,
it is normal that heat be expelled
in the area under the refrigerator.
Some floor coverings are sensitive
and will discolor at these normal
and safe temperatures.
Consumer Support Troubleshooting Tips Installation Instructions Safety InstructionsOperating Instructions
Before you call for service…
20