AMERITRON AL-800 User manual

AL-800 Instruction Manual
i
TABLE OF CONTENTS
Unpacking Instructions....................................................................................................1
Features ...........................................................................................................................3
AL-800 Technical Specifications....................................................................................4
General Information ........................................................................................................6
Safety Interlock....................................................................................................6
ALC.....................................................................................................................6
Dynamic Bias ......................................................................................................7
Timer - Overload Circuits ...............................................................................................7
Grid Overload Protection ....................................................................................7
Thermal Overload................................................................................................8
Cathode Warm-up Timer.....................................................................................8
Power Supply ..................................................................................................................8
Heater Supply......................................................................................................8
Plate (HV) Supply ...............................................................................................8
Meters..............................................................................................................................9
Current Meter (plate and grid):............................................................................9
Multimeter...........................................................................................................9
Multimeter Functions..........................................................................................9
Wattmeter Circuit................................................................................................10
Peak Envelope Power vs. Average Power...........................................................10
Tube Life.........................................................................................................................10
Export Modifications.......................................................................................................12
Technical Assistance.......................................................................................................12
Installation Guidelines and Suggestions..........................................................................13
Location Of The Amplifier.................................................................................13
Ventilation...........................................................................................................13
Power Connections..............................................................................................13
Grounding............................................................................................................14
Transformer Connections................................................................................................15
Jumper Connections........................................................................................................15
Interconnections ..............................................................................................................15
Operating Instructions And Guidelines...........................................................................16
Front Panel Controls............................................................................................16
Driving Power .....................................................................................................17
Tube and Component Life...................................................................................18
Additional SSB Notes .........................................................................................18
AM (Amplitude Modulation) Operation.............................................................19
Audio Distortion..................................................................................................19
FM (Frequency Modulation), RTTY, and DIGITAL OPERATION ..................19
ALC Metering, Controls, and Adjustments.....................................................................19
ALC Metering Functions.....................................................................................19
ALC Controls......................................................................................................20
ALC Adjustments................................................................................................20
Rear-panel "ALC LIMIT" control.......................................................................21

AL-800 Instruction Manual
ii
ALC Limit Adjustment (rear panel)....................................................................21
"ALC SET" control .............................................................................................22
Tuning .............................................................................................................................22
QSK Operation................................................................................................................25
Periodic Maintenance......................................................................................................26
Parts List..........................................................................................................................27
Timer / Overload Board (50-0117-2)..................................................................27
Power Supply / SWR Board (50-0800-1)............................................................28
Meter Board (50-0800-3) ....................................................................................29
Tuned Input Board (50-0800-2) ..........................................................................29
AL-800 Tuned Input Chart..................................................................................29
AL-800 Main Chassis Parts List..........................................................................30
Frequency Coverage........................................................................................................31
Amplifier Tuning Log .....................................................................................................31
Notes: ..................................................................................................................31
Schematics.......................................................................................................................32
Power Supply / SWR Board................................................................................32
Tuned Input Board...............................................................................................33
Meter Board.........................................................................................................34
Timer / Overload Board ......................................................................................35
Main Chassis.......................................................................................................36

AL-800 Instruction Manual
1
Ameritron AL-800
1200 Watt Linear Amplifier Instruction Manual
The Ameritron AL-800 is a 1200 watt PEP output linear amplifier that operates from 160 through
15 meters. The AL-800X and AL-800Y are export models that operate from 160 through 10 meters.
Export modification instructions are only available with proof of a valid amateur radio license.
The AL-800 uses a single 3CX800A7 tube in a class AB2 grounded grid circuit. High-quality
power supply and RF components combine with an accurate peak-detecting directional coupler,
front panel adjustable true ALC circuit, electronic grid current and thermal overload protection, and
automatic bias switching to make this the best featured and most reliable single 3CX800A7
amplifier available. The AL-800 and AL-800Y are factory-wired for 120 volt, 50/60 Hz ac line
voltage. The AL-800X is factory wired for 240 volt, 50/60 Hz ac line voltage. All models are
easily converted to other supply voltages between 90 and 250 volts ac.
WARNING:
NEVER APPLY POWER TO THIS AMPLIFIER WITH THE COVER REMOVED!
CONTACT WITH THE VOLTAGES INSIDE THIS AMPLIFIER CAN BE FATAL!
PLEASE READ THIS MANUAL BEFORE ATTEMPTING TO OPERATE EQUIPMENT!
Improper or abusive operation of this amplifier can damage the tube or other components in
this amplifier. Damage caused by improper or abusive operation is not covered under the
warranty policy.
Unpacking Instructions
Remove the 3CX800A7 tube from its shipping carton. Carefully unwrap the tube and inspect it for
visible damage. Look for a dented anode cooler and broken or bent pins. Roll the tube over slowly
and listen for loose internal materials. Contact either your Ameritron dealer or Ameritron
immediately if any damage exists.
Carefully lift the amplifier from the shipping carton, and place it on a firm, level surface. Inspect
the amplifier for shipping damage. Contact either your Ameritron dealer or Ameritron immediately
if any damage exists. Remove the cover screws with a #2 Phillips screwdriver. Save the screws to
re-secure the cover. Carefully lift the rear of the cover while sliding the cover back. The AL-800 is
shipped with the rubber chimney, fuses and fuse caps packed inside the amplifier. Additional
screws will be included in the fuse pack if they are required.
WARNING:
Never remove the cover while this amplifier is connected to the power mains!
Contact with the voltages in this amplifier can be fatal.
The tube must be installed in its socket prior to operation. Observe the pin configuration on the tube
and the socket. Two of the pins are separated by a large space. Carefully observe the pin alignment

AL-800 Instruction Manual
2
to be sure the tube pins are centered on the socket's metal contacts. Firmly press the tube into its
socket. Do NOT twist or force the tube into the socket.
Install the rubber chimneys over the tube. The seam of the chimney must face the fiber panel. The
bottom of the chimney has notches that must fit over the grid connectors near the base of the tube.
The heavy copper strap anode lead connects to the spacer on the center panel with the 6-32 screw
and nut provided. Install the anode spring clip connector on the tube's anode cap.
The top cover should now be installed with the vent holes on side of the cover positioned near the
electrolytics. The vent holes on the top of the cover should be on the right side of the amplifier
(front view). Secure the cover by installing the corner screws first. Install all the screws loosely
until every screw is in place. Tighten the screws after they have all been installed.
Install the fuses and fuse caps on the back of the amplifier. This amplifier uses two 20A fuses for
standard 120 Vac operation. If you wish to operate the amplifier on a line voltage other than 120 V,
the jumpers on the power transformer primary windings must be changed. If the line voltage wiring
is changed, the correct fuses must be installed. See the TRANSFORMER CONNECTIONS
section on page 15 for more information.
CAUTION: Always use fast-blow fuses rated at 250 volts or higher. NEVER use standard
automotive fuses or slow-blow fuses.
Note: Ameritron will NOT be responsible for shipping damage due to improper packing. The
packing materials used to ship this amplifier are specially designed to prevent damage. All
packing materials should be retained for future shipping. Replacement packing materials
may be purchased from Ameritron if original packing materials are unavailable.

AL-800 Instruction Manual
3
Features
1. The AL-800 uses a rugged high-gain 3CX800A7 tube.
2. A time-delay circuit provides a 180 second warm-up to eliminate potential damage to the tube
cathode.
3. A grid overload circuit quickly disables the amplifier if the grid current becomes excessive.
This feature prevents excessive grid current from causing distortion or damaging the tube or
other components.
4. A thermal overload automatically disables the amplifier if excessive heating of the power
transformer occurs.
5. A dynamic bias circuit eliminates hundreds of watts of unnecessary heat generation in the
power amplifier tube. The result is cooler operation and longer component life.
6. A multi-voltage heavy-duty transformer with a unique "buck-boost" winding allows
adjustment of the primary voltage to 14 different voltages centered on 115 and 230 volts. This
versatile Ameritron feature allows the user to select the optimum primary voltage for maximum
performance and life.
7. The tuning and loading controls have vernier 6:1 reduction drives for smooth tuning.
Logging scales allow quick and repeatable control adjustments for rapid band changes.
8. The AL-800 has two illuminated cross-needle panel meters. The left meter provides a
continuous reading of grid and plate currents. The right meter reads peak RF power output on
one scale and Plate Voltage (HV), Reflected power and SWR (REF), ALC detector voltage
(ALC), and ALC adjustment level (ALC SET) on the other scale.
9. Heater and plate voltages are maintained using the "STBY/OPR" switch. This allows the
amplifier to be conveniently bypassed for "barefoot" operation.
10. A front panel "ALC SET" control allows convenient adjustment of the ALC threshold. The
unique ALC circuit samples the grid current and power supply voltage.
11. "XMT" and "OL" LED's on the front panel indicate proper operation of the amplifier.
12. A rear panel 12 Volt auxiliary output jack provides up to 200 mA at 12 Vdc for accessories
such as the ATR-15 Antenna Tuner.
13. A step-start circuit limits the inrush current to the power supply and tube heater. This circuit
extends the life of the amplifier components.

AL-800 Instruction Manual
4
AL-800 Technical Specifications*
Input:
Circuit type: Pi-network, slug tuned coils
Maximum VSWR at resonance: 1.3:1 or less
Minimum 2:1 VSWR bandwidth: 20% of center frequency
Maximum drive power permissible: 100 watts PEP
Typical drive for full power output: 85 watts
Output:
Circuit type: Pi-L, Pi-network
Typical SSB PEP voice operation: 1200 + watts
CW continuous operation: 850 watts
1/2 hour PEP two-tone test: 1200 watts
1/2 hour continuous carrier (RTTY): 700 watts
Frequency Coverage: 1.8 to 21 MHz amateur Bands. (Export models
include 24.5 and 28 MHz)
Third Order IMD: -35 dB or better (at rated output)
Efficiency:
CW: approximately 65%
SSB: approximately 65% (envelope crest)
Power Supply:
Circuit type: Full wave voltage doubler
No load voltage: 2600 V
Full load voltage: 2250 V
Full load current: 1.2 A
Regulation: 12%
Transformer: 32 lb. E-I lamination grain oriented
Capacitors: 63 mFd total, computer grade
Normal line current at rated CW output: 16A at 120 Vac
Normal line current at 1200 watt PEP output: 17 A at 120 Vac
Power line current in standby: 0.9 A at 120 Vac
Tube:
Type: 3CX800A7
Continuous dissipation: 800 watts total
Warm-up time: 180 seconds
Estimated life: 8,000 hours ICAS
* Exact performance measurements may vary due to the accuracy of test equipment and the measurement methods
used. (Prices and specifications subject to change without notices.)

AL-800 Instruction Manual
5
Metering:
Multimeter: Peak forward power (continuously). The second scale switches between peak
reflected power (and SWR), ALC threshold, ALC output voltage, and high voltage.
Current meter: Plate and grid current (simultaneously) on separate scales.
ALC:
Negative going, 0 to 10 volts, adjustable.
Relay:
Requires contact closure or sink of +12 Vdc at 100 mA. Back pulse protected.
Connectors:
RF: SO-239
Line: NEMA 5-15P, standard 120 V three wire
Others: RCA Phono
Physical:
Dimensions: 14-1/2"D x 14-1/4"W x 8-1/2"H
Weight: 68 lbs.

AL-800 Instruction Manual
6
General Information
Safety Interlock
An interlock switch is closed while the amplifier's top cover is in place. This switch allows ac line
voltage to reach the power transformer. The interlock will open and remove line voltage from the
transformer primary if the top cover is removed.
WARNING:
High voltage can kill!! Accidental contact with the voltages in this amplifier can be lethal.
For your personal safety please observe the following precautions:
1.) NEVER defeat the interlock.
2.) NEVER remove the cover with the amplifier connected to the power line.
3.) ALWAYS allow the capacitors to discharge for several minutes after unplugging the amplifier
and before removing the cover.
4.) ALWAYS select the high-voltage (HV) function of the Multimeter to check the high voltage
potential. Do not remove the cover if voltage is indicated.
5.) ALWAYS ground the tube anode (outer metal surface) to the chassis through a low value, high
wattage resistor before touching anything inside the amplifier.
6.) ALWAYS be cautious of heat. Many components inside the amplifier operate at high enough
temperatures to cause burns.
7.) NEVER make any unauthorized component or circuit modifications to this product. The only
acceptable source for modifications is Ameritron or a source approved by Ameritron.
Unauthorized modifications almost certainly will increase the risk of equipment failure or
personal injury.
ALC
The AL-800 is one of the few amplifiers using a "true" automatic level control ALC circuit. In this
amplifier, the ALC actually samples grid current and power supply loading to determine the ALC
voltage. The front panel "ALC SET" knob adjusts the level of grid current where ALC action
begins. The ALC action begins softly over a range of a few milliamperes to minimize distortion.
This soft-touch ALC is an Ameritron exclusive.
The ALC circuit is located on the METER BOARD P/N 50-0800H-3 (behind the
"MULTIMETER" switch). IC301 (pin 9) samples the voltage drop (caused by grid current)
across R106 in the main power supply board. ALC voltage is derived by comparing the grid shunt
voltage to the voltage from the power supply (pin 10).

AL-800 Instruction Manual
7
Pin 8 of IC1 will go negative if the grid shunt voltage exceeds the voltage from divider R311 and
R2 (chassis mounted control), or if the supply voltage sags from excessive line voltage drop. Pin 8
is followed by current buffer Q303 that sources the negative ALC voltage to the ALC output jack.
Dynamic Bias
Conventional bias circuits allow high power linear amplifiers to dissipate hundreds of watts during
low or no signal periods. This creates needless heat, since virtually no dissipation is required unless
the amplifier is being driven with large signal levels.
The AL-800 contains an exclusive bias circuit that reduces the idling (quiescent) current very close
to the tube's cut off region. The power amplifier tube in the AL-800 has a full resting period of very
low dissipation between dots and dashes on CW and between words on SSB. The lower idling
current dramatically reduces component temperatures on both CW and SSB. If only a few
milliwatts of RF power are applied to the amplifier, the quiescent current will increase. Linearity
remains excellent with this circuit because the tube's conduction angle is never reduced below class
AB.
The dynamic bias circuit is located on the Power Supply Board P/N 50-0800-H1. Diodes D101 and
D102 rectify a small sample of the RF drive voltage. This voltage is applied to the base of dc switch
Q101. If Q101's base is driven with a few microamperes of current from the RF sampling circuit,
Q101's collector will pull the base of PNP transistor Q102 low. This turns dc switch Q102 on.
When Q102 is on, zener diode D103 is connected between the collector and base of Q103.
D103 sets the operating bias. This zener applies forward bias to Q103's base whenever the collector
voltage of Q103 exceeds the voltage of D103. This forward bias will turn Q103 on harder and will
reduce the collector voltage. If the collector voltage is less than the breakdown voltage of D103,
Q103 will move towards cut-off and the collector voltage will increase. Q103 is, in effect, a current
buffer for zener diode D103.
Timer - Overload Circuits
CAUTION: Never modify or disable protection circuits without factory approval. Doing so
with void all manufacturer's warranties.
Grid Overload Protection
This amplifier contains a fast acting electronic grid protection circuit to enhance tube life. The
amplifier will quit operating and the "OL" and "XMT" LEDs will both illuminate if the safe limit
of grid dissipation is approached or exceeded. The grid overload protection circuit is reset whenever
the "STBY-OPR" switch is placed in the "STBY" position.
Note: This circuit has a much faster response time than the grid meter. This circuit also
measures the peak grid current. The operator may not observe the grid current
meter climbing before the overload circuit responds and disables the amplifier.

AL-800 Instruction Manual
8
This circuit is located on the Timer / Overload board P/N 50-0800-5. IC501 (pin 5) senses the
voltage across the grid shunt (power supply board, R106) through terminal 1. If the voltage at pin 5
exceeds the regulated voltage at the junction of R505 and R511, the output of IC501 (pin 7) will go
high and turn on Q504. Q504 will energize the coil of RL501. RL501 will latch "on" and remove
the voltage from terminal 3 and relay RLY101 (power supply board).
Thermal Overload
The transformer in this amplifier contains an internal temperature sensor. This sensor disables the
transmit function if the transformer's temperature ever happens to approach the limit of safe
operation. Thermal overload is indicated if the "OL" LED illuminates without the "XMT" LED
being illuminated.
The amplifier will not operate during a thermal overload indication. The thermal protection system
automatically resets after several minutes of a non-transmitting cool down period.
Cathode Warm-up Timer
Indirectly heated transmitting tubes normally require a few minutes of "warm-up" time before plate
current can be drawn. This protection is provided by IC501 (see Tube Life on page 10).Pin 2 of
IC501 is connected to a regulated reference voltage. C509 begins to charge when the main power
switch is placed in the ON position. The voltage at pin 3 of IC501 will exceed the voltage on pin 2
after approximately three minutes, causing the output of IC501 (pin 1) to go high.
Q503's collector pulls low whenever the output of IC501 (pin 1) is high. When the collector of
Q503 is low, Q502 and Q501 are forward-biased. This allows 12 volts to appear at terminal 5.
Terminal 5 supplies 12 Vdc to the keying circuits and the plate and grid current meter lamp.
Power Supply
Heater Supply
The heater circuit of this amplifier satisfies all requirements of the tube manufacturer related to tube
performance and life. The heater voltage and inrush current are controlled by the power
transformer's internal resistance and impedance, heater choke resistance, heater wiring resistance,
and the step-start circuit. For maximum tube life, NEVER replace any circuit components or wiring
with substitute parts. Always consult the factory before making modifications that may affect tube
life.
Plate (HV) Supply
The plate supply uses a full wave doubler circuit with 200 amp surge rated diodes and a heavy duty
32 pound grain oriented transformer with internal thermal protection. Filtering is accomplished by a
bank of high quality computer grade capacitors totaling 63 mFd. Large 50k-ohm 7-watt bleeders are
used for safety and superior voltage equalization. The transformer allows user selection of fourteen
different line voltages (See the Transformer Connections section on page 15 for details).

AL-800 Instruction Manual
9
Power is supplied through "OFF-ON" switch S2. A 10 ohm resistor (R27) limits the line current
during the filter capacitor charge time to lower component stress. When the filter capacitor
charging
current decreases sufficiently, RLY102 shorts the 10 ohm resistor. This applies full power line
voltage to the transformer. The 10 ohm resistor is protected from high-voltage supply shorts by a
two-ampere fast-blow fuse (F101) during start-up. If F101 or the 10 ohm resistor (R27) fails the
amplifier will not start. If F101 fails from a momentary HV to ground fault, meter protection diode
D117 may also fail. See the Meters section that follows for more information.
Meters
Current Meter (plate and grid):
The plate and grid current meter is located on the far left side of the front panel. This meter
indicates the plate current (Ip) on the right-hand meter scale. This scale has a small picket every
0.05 ampere, a large picket every 0.25 ampere, and indicates 1.5 amperes at full deflection.
The left-hand meter scale indicates the grid current (Ig). The small pickets on this "Ig" scale appear
every 5 mA and the larger pickets appear every 25 mA. The full scale "Ig" reading is 125 mA.
The plate and grid meters in this amplifier will normally indicate maximum grid current and
maximum RF output near the same "PLATE" tuning setting during adjustments. Maximum grid
current and minimum plate current also generally occur at or near the same "PLATE" tuning setting.
Note: If the grid and plate meters always track (move together in exact step) as the tuning
controls are adjusted and if they show the same approximate amount of pointer
movement, diode D117 on the power supply board could be shorted.
D117 protects the overload circuit and the meters. This diode is located near the electrolytic
capacitors on outside edge of the main circuit board. D117 will usually short if there is a large high-
voltage-to-chassis current fault. The grid and plate current meters will not read correctly if this
diode fails. The overload circuit may repeatedly trip before full power is reached if D117 is shorted.
Multimeter
The multimeter is the meter on the right. It continuously reads the forward peak envelope power on
its left-hand scale (FWD). This scale is calibrated in 100 watt steps up to 2 kW.
The right-hand scale of this meter serves multiple functions, including measurement of the high
voltage (HV), reflected power (REF), SWR, ALC voltage output (ALC), and relative ALC threshold
(ALC SET). These four metering functions are selected by the "MULTIMETER" switch. See
Multimeter Functions for more information.
Multimeter Functions
HV: The multimeter will indicate the dc plate voltage of the PA tube when in the HV position. The
correct scale to use is the ACL / HV scale, which has a picket every 100 volts. Two zeros must be
added behind the numbers indicated on the meter scale (i.e. multiply by 100), so that "25"=2500

AL-800 Instruction Manual
10
volts and "20"=2000 volts. Do not operate the amplifier if the high voltage is over 2700 volts with
the amplifier on standby. See the Transformer Connections section on page 15 for
information on correcting excessive high voltage.
REF:The multimeter measures the antenna (or load) peak envelope reflected power in the REF
position. The full scale reflected power reading is 500 watts. This scale is marked every 10 watts
below 100 watts, and every 100 watts from 100 to 500 watts.
Note: The SWR of the load can be measured when the "MULTIMETER" switch is in the REF
position by observing the different red SWR curves. The forward and reflected meter
pointers will cross each other on, or near, the correct SWR curve.
ALC: The multimeter measures the output voltage of the ALC detector when in the ALC position.
The full scale ALC reading is 35 volts and is read directly from the ACL / HV scale. The meter
should flick upwards occasionally during normal ALC action. See ALC Metering,
Controls, and Adjustments operation on page 19 for more information.
ALC SET:The multimeter measures the approximate grid current that will produce ALC activity
when the meter switch is in the "ALC SET" position. One zero must be added to the reading on
the ACL / HV scale and the result divided by 2 for this function. For example, ALC action will
begin at approximately 75 mA of grid current (typically between 60 mA and 90 mA) when the
"ALC SET" control is adjusted until the meter reads "15."
Wattmeter Circuit
The AL-800 wattmeter circuit uses an accurate directional coupler followed by a true peak detector
circuit. This circuit will accurately determine the true peak envelope power (PEP) of normal voice
waveforms. If the load SWR is high, the true power reading can be obtained by subtracting the
reflected power from the forward power reading.
Peak Envelope Power vs. Average Power
Peak envelope power (PEP) is often misunderstood. PEP is not associated with the sine wave or
root-mean-square (RMS) power, and it has no fixed ratio to average power. There are no formulas
that allow accurate conversions between average and peak voice waveform power.
PEP is the power at the crest (highest point) of the RF waveform. On SSB, the average power can
vary from a few percent of the PEP to over fifty percent of the PEP. Generally, the PEP on SSB is
two to five times greater than the average power. On CW or other constant amplitude modes (such
as FM or RTTY), the PEP is always equal to the average power.
Tube Life

AL-800 Instruction Manual
11
The 3CX800A7 is a reasonably rugged tube. The anode can handle very large anode dissipation
overloads for short periods of time due to the thermal mass of the external anode. Care must be
taken to avoid exceeding the temperature ratings of the tube's ceramic-to-metal seals. The life of the
tube in this amplifier may be prolonged if adjustment periods are kept short and a brief "cool-down"
periods are provided between lengthy adjustment periods. Avoid shutting the main power off
immediately after lengthy full power CW or RTTY transmissions. After lengthy full power RTTY
or CW transmissions, allow a one or two minute "cool-down" period (without transmitting) before
shutting off the ac power switch.
The most sensitive element in any indirectly heated oxide cathode tube will always be the control
grid. A fraction of a second of incorrect tuning can cause control grid damage. This is especially
true in amplifiers that use fuses or resistors to protect the grids. Fuses and resistors are much too
slow and too unpredictable to adequately protect control grids. In this amplifier, the 3CX800A7 grid
is protected by a fast-acting electronic circuit. This circuit rapidly disables the amplifier when
excessive grid dissipation occurs. Never remove or defeat this circuit. Doing so will void the
manufacturer's warranty.
In the AL-800, a grid current of 75 mA (at 100 watts of drive) produces the maximum rated grid
dissipation of 4 watts. This amount of grid current will also safely disable the amplifier within a few
milliseconds.
WARNING:
NEVER drive this amplifier with more than 100 watts of short term average envelope power.
NEVER remove, defeat, or modify the internal electronic grid protection circuits.
Maximum power output normally occurs with a maximum of 15 to 20 mA of grid current on CW,
or 12 mA indicated (25 mA peak) during a SSB two-tone test. The grid dissipation is well under one
watt with 25 mA of grid current and 100 watts of drive.
The cathode of the 3CX800A7 must reach full operating temperature before the tube is operated.
The cathode becomes fully operational 180 seconds after the application of the full heater voltage.
The warm-up timer in this amplifier assures that the cathode reaches the proper operating
temperature before the amplifier can be operated. Never defeat the warm up timer or alter the heater
voltage.
The continuous commercial plate current rating of the 3CX800A7 is 600 mA. Brief periods of plate
current exceeding 1.2 amperes (during tuning) will not cause loss of emission or shorten the amateur
life of the tube in this amplifier. For maximum tube life, plate current should be maintained below
700 mA on normal amateur CW operation, 600 mA on FM, RTTY, and other "steady" carrier
modes. The life a metal oxide cathode is directly related to the accumulated heater operating
time, not the transmitting time.
The application of heater or filament voltage causes thermal stresses from rapid and uneven
temperature changes in the tube's heater. Avoid unnecessary main power switch cycling to prevent
needless heater life reduction.

AL-800 Instruction Manual
12
An accumulation of gas (or stray debris) in the tube can cause the tube to arc between the anode and
the other elements of the tube. The resulting "gas arc" will generally manifest itself as a loud "pop"
when the amplifier is first turned on, or during conditions of high anode voltage. A "gas arc" will
often damage diode D117 on the negative rail of the filter capacitor bank and open the fuses in the
amplifier. If this problem occurs frequently, the tube should be tested or replaced. The use of low
quality tubes, tube that have been stored for extended periods, or abused tube will increase the
likelihood of a "gas arc". Ameritron recommends using only current code date Eimac 3CX800A7
tubes.
Export Modifications
A simple modification will allow operation on frequencies above 15 meters. Instructions for this
modification are available by sending a written request for "Export Modification Instructions" along
with a copy of a valid amateur license. There is no charge for this information. Export models are
shipped with this modification installed and have an "X" or "Y" following the serial number.
Standard frequency ranges are indicated in the chart on page 32.
Technical Assistance
Technical assistance is available during normal central standard time business hours on weekdays.
Customer service is more effective when our engineers are provided the following information:
1. Model and serial number
2. Date of purchase and dealer
3. An accurate description of the problem
Meter readings at all stages of the tuning procedure are very important along with a complete
description of the other equipment used with our product.
Written assistance is also available. Due to time delays in processing mail, please allow at least
three weeks for a written reply. For service or written correspondence, use the following address:
AMERITRON
116 Willow Rd.
Starkville, MS. 39759
Telephone [phone]
FAX [phone]
Note: Service history has clearly shown that most problems are operating or installation errors,
rather than equipment failures. Most problems can be resolved over the telephone.
Please contact our staff before shipping parts or equipment to us.
The packing materials used to ship this amplifier were specially designed to prevent shipping
damage. The original packing materials should be used to ship this amplifier. Replacement packing
materials may be purchased from Ameritron if original packing materials are unavailable or
damaged.

AL-800 Instruction Manual
13
CAUTION: Never ship this amplifier with the tube installed. Ameritron will not be
responsible for shipping damage caused by improper packing.

AL-800 Instruction Manual
14
Installation Guidelines and Suggestions
Location Of The Amplifier
Do not install the amplifier in excessively warm locations or near heating vents or radiators. Be
sure air can circulate freely around and through the amplifier cabinet. Provide an unobstructed cold
air inlet for the amplifier. DO NOT place any books, magazines or equipment that will impede the
free flow of air near or on the cabinet ventilation holes.
Ventilation
The AL-800 ventilation system has been designed and tested to maintain tube seal temperatures
safely below the tube manufacturer's rating at 1200 watts of continuous two tone test SSB PEP
output, or 850 watts of continuous RTTY, FSK, FM or CW power output when the amplifier is
properly tuned. The blower in the AL-800 is a permanently lubricated type that requires no
maintenance in normal operation. To insure adequate cooling in your installation, please observe
the following:
1.) Do not block or unduly restrict the ventilation holes in the cover. Be sure that the amplifier is
located in an area so the ventilation holes have open air circulation. It is particularly important
to avoid restricting the air inlet.
2.) The exhaust airflow is over 30 CFM. Do not "assist" the exhaust airflow with cabinet mounted
fans.
3.) The most efficient way to improve airflow is to pressurize the air inlet area. Be sure that any
fan used to assist the inlet airflow has at least a 60 CFM rating.
4.) The exhaust air will become quite warm at high power levels. Do not place any heat sensitive
objects in the exhaust air stream.
Power Connections
The AL-800 is supplied with a NEMA 5-15P plug for 120 Vac operation. The Transformer
Connections section on page 15 show the correct wiring for various supply voltages.
This amplifier has a current demand of approximately 16 amperes at 120 Vac with 1200 watts of
carrier output and an absolute maximum draw of 20 amperes under severe operating conditions.
The average power line current during voice peaks on SSB will be approximately 6 amperes at 1200
watts PEP output. Most normal residential power lines and house-wiring should meet this demand
for current.
If the power mains have excessive resistance, the high voltage may sag to less than 2200 volts under
load. Voltage sag will not hurt the life of the amplifier components if the fully loaded high voltage
remains above 2000 volts. 240 volt operation will help improve performance if the power wiring is
marginal.

AL-800 Instruction Manual
15
CAUTION: Never allow the high voltage to exceed 2700 volts under any condition.
For 120 volt operation, the wiring between the fuse box and the amplifier ac outlet must be number
12 gauge (or larger) in order to supply the current required (16 A) without a significant drop in the
line voltage. The 120 volt outlet should be fused properly for the gauge of house-wiring used, but
never exceed 25 amperes.
Grounding
Connect a good RF and dc ground to the ground post on the rear panel of the amplifier. Use the
heaviest and shortest connection possible. The best materials to use for ground connections are (in
order of effectiveness) smooth wide copper flashing, copper tubing, or solid copper wire. Never use
braided or woven conductors unless the lead needs to be flexible. Braided or woven conductors
offer a high impedance to both lightning and RF.
Water pipes, metal heating ducts, metal fences and other large metallic masses offer convenient RF
grounds. If a water pipe ground is used, inspect all the pipe connections to be sure that no plastic or
rubber connections are insulating the pipes. Insulated pipe connections will interrupt the electrical
continuity to the water supply line. Install a jumper around any insulated pipe connections you find.
Use heavy copper wire or flashing with stainless hose or pipe clamps for the jumpers.
The following tips will help prevent lightning damage and RF grounding problems:
1.) Avoid using braided or woven conductors, they have very high resistance to both RF and
lightning currents. RF and lightning flows along the surface of conductors, almost no current
flows in the center of the conductor. The lowest RF resistance occurs with wide, smooth
conductors.
2.) Avoid routing a single small gauge grounding conductor along the various pieces of equipment
(or to connect multiple ground sources). Instead, use multiple ground leads that connect to a
single wide buss at the operating position. Keep all ground leads as short and wide as possible.
3.) Buried radials provide much better lightning and RF grounds than ground rods do, although
both are needed for safety.
4.) Avoid sharp bends in ground leads. When changing the direction of a ground lead use a
gradual radius turn.
5.) Avoid second story operation. A good ground is much easier to obtain on the first floor or in
the basement of a structure.
6.) Air-core choke baluns should be used on all coaxial feedlines. The feedlines should be coiled
into several 4" to 6" diameter turns before they enter the building. Either directly bury the
feedlines a few inches deep in the ground for a minimum distance of ten feet or ground the
shields to a separate outside ground on the antenna side of the choke.

AL-800 Instruction Manual
16
Transformer Connections
The power transformer of the AL-800 has fourteen different voltages available on the primary and is
rated at full power with supply frequencies of 50 to 60 Hz and voltages above 100 volts. The
Jumper Connections chart below indicates the proper placement of jumpers for various
power line voltages.
Jumper Connections
CONNECT A JUMPER FROM THE BOLD COLUMN HEADING LETTER ("A" - "F") TO
THE LETTER OR NUMBER IN THE ROW NEXT TO THE DESIRED "HIGHEST LINE
VOLTAGE". DANGER: Never change jumpers with the power cord connected to an outlet.
Highest
Line-V "A" "B" "C" "D" "E" "F" Line Fuse
205 C(B) 3 1 12
215 C(B) 3 2 12
220 C(B) 2 1 12
230 C(B) F(E) 10
240 C(B) 1 2 10
245 C(B) 2 3 10
250 C(B) 1 3 10
90 (B) A(D) C3 1 25
100 (B) A(D) C3 2 25
110 (B) A(D) C2 1 25
115 (B) A(D) CF(E) 20
125* (B) A(D) C1 2 20
130 (B) A(D) C2 3 20
140 (B) A(D) C1 3 20
* Factory wired
WARNING:
The AL-800 requires different back panel fuses for various line voltages. Use the fuse listed
in the JUMPER CONNECTIONS chart for maximum protection.
Interconnections
1. Connect the exciter's RF output to the "RF IN" connector on the rear of the AL-800 with 50
ohm coax. Use any good quality 50 ohm cable long enough to connect the amplifier to the
exciter. This amplifier connection uses a standard SO-239 female that mates with a PL-259
male connector on the cable.

AL-800 Instruction Manual
17
2. Connect the existing station antenna system to the "RF OUT" connector on the rear of the AL-
800 with RG-8 type coax. This amplifier connection uses a SO-239 female that mates with a
PL-259 connector on the cable.
3. Shielded audio type cable with a standard male phono plug should be used to connect to the
"RLY" jack on the AL-800. This jack has positive 12 Vdc open circuit and supplies 100 mA
of current when pulled to ground. The relay circuit has an internal back pulse canceling diode
to protect sensitive exciter circuits from damage.
4. Connect a short, wide, and smooth ground lead from a good earth and RF ground to the rear
panel "GND" terminal. Avoid using braided conductors for ground leads.
5. The "12 V" connection on the rear panel provides 12 Vdc at 200 mA maximum to operate
external dial lamps or accessories such as the ATR-15 Antenna Tuner.
6. Connect the "ALC" jack to the ALC input of the exciter with a shielded cable and a phono
plug. The proper connection point on the exciter should be indicated in the exciter's manual.
The AL-800 ALC will operate with any exciter that uses a negative-going ALC voltage of up to
10 volts.
Note: Transceiver ALC response times and ALC voltage requirements vary with different
manufacturers. The ALC section describes adjustment of this circuit in detail.
Operating Instructions And Guidelines
Front Panel Controls
"MULTIMETER" Switch
This four position switch selects either the plate voltage (HV) of 0-3500 volts, the reflected peak
envelope power (REF) of 0-500 watts, the ALC detector output voltage (ALC) of 0-35 volts, or the
approximate ALC grid current threshold (ALC SET) of 0-175 mA. See the Meters section on
page 9 for more details.
"OFF-ON" Switch
This switch turns the main power off and on. When this switch is placed in the "ON" position the
blower should start, the right-hand meter should be illuminated, and high voltage should appear.
The left-hand meter should illuminate and the amplifier should operate after three minutes.
"STBY-OPR" Switch
This switch disables the amplifier's internal antenna relay and resets the grid protection circuit. In
the "STBY" position the amplifier is bypassed without turning the tube's heater or the power supply
off.
This switch will also reset the grid protection circuit if the "OL" LED is illuminated. The overload
circuit is automatically reset whenever this switch is placed in the "STBY" position and returned to
the operate position.

AL-800 Instruction Manual
18
"PLATE" Control
The "PLATE" control adjusts the output tank circuit to resonance. This control should always be
adjusted for maximum RF output power. Maximum RF output power normally occurs
simultaneously with maximum grid current and very close to the plate-current "dip."
"LOAD" Control
This control adjusts the coupling of the amplifier to the antenna. This adjustment is necessary to
insure optimum coupling to the load as the SWR of the load, the operating frequency, or the power
level is changed. Advancing the "LOAD" control clockwise increases the RF power output
capability and the linearity of the amplifier. Advancing the "LOAD" control also decreases the
grid current and increases the plate current for a given amount of drive.
The efficiency of the amplifier and the grid current decrease if the "LOAD" control is rotated
beyond the point of maximum output. The linearity, however, will increase. The proper position
for this control is slightly clockwise from the setting that produces maximum output with full drive-
power applied. Never use this control to adjust the output power.
CAUTION: Failure to adjust the loading control properly can result in excessive tank
circuit voltages and damage to components.
The "PLATE" control should always be checked after the "LOAD" control is adjusted by more
than one number. For example, if the "LOAD" is advanced from 1-1/2 to 2-3/4, the "PLATE"
should be re-tuned. If the "LOAD" is touched up a small amount, the "PLATE" setting will not
usually require re-adjustment.
Driving Power
This amplifier is designed to operate at full ratings when it is driven by an exciter that has
approximately 85 watts of RF output. An exciter with a lower output power may be used with a
resulting decrease in amplifier output. Both the driving power and the "LOAD" control must be
carefully adjusted when using an exciter that delivers more than 85 watts. Proper control settings
will help prevent excessive grid current and spurious signals, which create needless interference to
other operators. A monitor scope is recommended for continuous output observation. An
oscilloscope is the best way of determining if the amplifier is "flat-topping" and producing excessive
distortion products.
A second method of determining linear operation is to monitor the peak RF output power carefully
on the AL-800's internal meter. Determine the maximum obtainable RF output power and reduce
the exciters power until there is a noticeable margin from the maximum output power. This will
insure some reserve power is available for random voice peaks.
Note: Never increase the drive power beyond the point where the amplifier's output power
stops increasing. This is also the point where the grid current will begin rising rapidly.