
- 18 -
DISPLAY CONTROL
When the refrigerator door is closed and there is no button operation in 3 minutes, the display light
goes o.
When the display light is o, open the refrigerator door or click any button to light it up.
TEMPERATURE SETTING
1) Click the “refrigerator” or “freezer” button and when it ickers in the symbol, temperatures can be
set; each time when the button is clicked, the temperature changes accordingly (the display shows the
temperature accordingly). (Temperatures cannot be set under functions of fast cooling, fast freezing,
SmartECO and vacation,)
2) Under temperature setting, if there is no button operation in 5 seconds, the button stops ickering
and the set temperature comes into eect.
3)Temperature cycle
Refrigerator: 2OC→ 3OC→ 4OC→5O C→ 6OC→ 7OC→ 8OC→ OFF→ 2OC
Freezer: -24OC→ -23OC→ -22OC→ -21OC→ -20OC→ -19OC→ -18OC→ -17OC→ -16OC→ -24OC
SMARTECO
Under SmartECO, it is 4OC in the refrigerator and -18OC in the freezer.
Temperatures cannot be changed and you can click the temperature zone button to check the temper-
ature.
1) To enter SmartECO
Click “option” until it ickers and then click “OK” to enter this function.
2) To quit SmartECO
Under SmartECO, click “option” until it goes to SmartECO, click “OK” to quit this function and the light
goes o.
Temperatures of each chamber go back to the value before SmartECO function.
FAST COOLING
Under fast cooling, it is 2OC in the refrigerator and the refrigerator temperature cannot be changed.
1)To enter fast cooling
Click “option” until it ickers in “fast cooling” and then click “OK” to enter this function.
2) To quit fast cooling
Under fast cooling, click “option” until it goes to “fast cooling” and then click “OK” to quit this function.
The light in fast cooling goes o and the refrigerator temperature goes back to the value before fast
cooling.
FAST FREEZING
Under fast freezing, refrigerator temperature can be set but not for the freezer temperature.
1) To enter fast freezing
Click “option” until it ickers in “fast freezing” and then click “OK” to enter this function.
2) To quit fast cooling
Under fast freezing, click “option” until it goes to “fast freezing” and then click “OK” to quit this function.
The light in fast freezing goes o and the freezer temperature goes back to the value before fast
freezing.
When fast freezing time is up (26 hours), it quits automatically.
When it goes to SmartECO, fast freezing stops.
VACATION
Under vacation, it is 14OC in the refrigerator and the temperatures in this chamber cannot be changed.
1) To enter vacation
Click “option” until it ickers in “fast freezing” and then click “OK” to enter this function.
2) To quite vacation
Under vacation, click “option” until it goes to “vacation” and then click “OK” to quit this function.
The light in vacation goes o and the refrigerator temperature goes back to the value before vacation.
Vacation quits under functions of SmartECO and fast cooling.
POWER OFF MEMORY
With this design, the refrigerator can automatically keep all the setting in case of power o. When the
unit is plugged in again, the refrigerator will run with the setting before power o.
POWER-ON DELAY
To prevent harm to the refrigerator in case of sudden power cut and power on, the unit does not start
immediately if the power o time is less than 5 minutes.
FREEZER OVER-TEMPERATURE ALARM (ONLY IN CASE OF POWER ON)
When the freezer temperature is higher than 10OC at the rst time connected to power, the symbol
light of the freezer chamber goes on and the number representing temperature ickers.
Press any button or wait for 5 seconds, ickering stops and it goes back to the temperature that was
set.
REFRIGERATOR DOOR OPENING ALARM
When the refrigerator is open over 3 minutes, the buzzer will buzz. Close the door or press any button
to stop the alarm, but for the latter, the alarm will go o again after 3 minutes.
Sensor fault alarm
When it shows “E0”, “E1”, “E2” or other abnormal symbols, it means sensor faults and the refrigerator
needs repair.