Amico AG series User manual

Owner’s
manual
*SAFETY
*ASSEMBLY
*OPERATION
*TROUBLESHOOTING
*WARRANTY
Portable Generator
AMICO POWER CORPORATION
13221 Spring Street, Baldwin Park, CA 91706
AG Series

Introduction……………………………………………....1
Read this Manual Thoroughly…………………………..1
Safety Rules………………………………...…………….5
St andards Index……………………………………………………...8
Section 1-General Information………………………….8
1.1 Unpacking……………………………………………………….8
1.1.1 Accessory box……………………………………………...8
1.2 Assembl y………………………………………………………...9
1.2.1 Assembling the accessory kit………… …………………...9
Section 2 – Operati on…………………………………..10
2.1 Know the generator…………………………………………….10
2.2 Cord Sets and connection Plugs………………………………..12
2.2.1 120 VAC, 20 Ampt, duplex receptacle………………..….12
2.3 How to Use the Generator……………………………………...12
2.3.1 Grounding the generator………………………………….12
2.3.2 Connecting electrical Loads……………………………...13
2.4 Don’t overload the generator…………………………………...13
2.5 Wattage Reference guide……………………………………….14
2.6 Before St arting the generator…………………………………..15
2.6.1 Adding engine oil………………………………………...16
2.6.2Adding gasoline…………………………………………..16
2.7 To St arting the generator…………………………………….....17
2.8 Stop the engine…………………………………………………19
2.9 Low oil level shutdown system…………………………….......19
2.9.1 Sensing low oil level……………………………………..19
Section 3 – Maintenance……………………………….19
3.1 Maintenance schedule………………………………………….19
3.2 Product specifications…………………………………………..20
3.2.1 Generator specifications…………………………………...20
3.2.2 Engine specifications………………………………………20

3.3 General recommendations………………………………………21
3.3.1 Generator maintenance……………………………………..21
3.3.2 T
o clean the generator……………………………………....21
3.3.3 Engine maintenance………………………………………..22
3.3.4 Checking oil level………………………………………….22
3.3.5 Changing the oil…………………………………………....22
3.3.6 Replacing the spark plug…………………………………...23
3.3.7 Spark arrestor………………………………………………24
3.4 Service air filter………………………………………………....24
3.5 Valve clearance………………………………………………… 25
3.6 General………………………………………………………….25
3.7 Long term storage……………………………………………… 25
3.8 Other storage tips……………………………………………….26
Section 4 – troubleshooting……………………………..27
4.1 Tr oubleshooting guide…………………………………….....27
Section 6 – notes ………………………………………...34
Section 7 – warranty……………………………………37
Section 5 - Circuit diagram.............................................29
Circuit diagram for AG5500..............................................29
Circuit diagram for AG6500..............................................30
Circuit diagram for AG7500...............................................31
Circuit diagram for AG8500...............................................32
Circuit diagram for AG9500...............................................33

INTRODUCTION
Thank you for purchasing this model by AMICO Power Corp.,
Inc this model is a compact, high performance, air-cooled, engine
driven generator designed to supply electrical power to operate
electrical loads on job sites, or remote locations where no utility
power is available or in place of utility due to a power outage.
READ THIS MANUAL THOROUGHLY
If any portion of this manual is not understood, contact the
nearest authorized dealer for starting, operating and servicing
procedures.
Throughout this publication, and on tags and decals affixed to the
generator, DANGER, WARNING, CAUTION and NOTICE blocks
are used to alert personnel to special instructions about a
particular operation that may be hazardous if performed
incorrectly or carelessly. Observe them carefully. Their definitions
are as follows.
After this heading, read instructions that, if
not strictly complied with, will result in serious personal
injury, including death and/or property damage.
After this heading, read instructions that, if
not strictly complied with, may result in serious personal
injury and/or property. And minor injury.
After this heading, read instructions that, if
not strictly complied with, could result in damage to
equipment and/or property, and minor injury.
After this heading, read explanatory
statements that require special emphasis and relate to
property damage.
These safety warnings cannot eliminate the hazards that they
indicate. Common sense and strict compliance with the special
instructions while performing the service are essential to
preventing accidents.
1
1

For commonly used safety symbols accompany the DANGER,
WARNING and CAUTION blocks. The type of information each
indicates is as follows.
This symbol points out important safety information
that, if not followed, could endanger personal safety and/or
property of others.
This symbol points out potential explosion hazard.
This symbol points out potential fire hazard.
This symbol points out potential electrical shock hazard.
The operator is responsible for proper and safe use of the
equipment. We strongly recommend that the operator read
this manual and thoroughly understand all instructions
before using the equipment.
Using a generator indoors WILL KILL YOU IN
MINUTES. Exhaust contains carbon monoxide, a poison gas
you cannot see or smell.
Never use in the home, or in partly enclosed far from open
windows, doors, vents, and in an area that will not
accumulate deadly exhaust gas.
Always disconnect the spark plug wire and
place the wire where they cannot contact the spark plug to
prevent accidental starting when setting up, transporting,
adjusting or making repairs to the generator.
2

The generator produces dangerously high voltage that can
cause extremely hazardous electrical shock, avoid contact
with bare wires, terminals, etc. never permit any unqualified
person to operate or service the generator.
Never handle any kind of electrical cord or device while
standing in water, while barefoot or while hands or feet are
wet. Dangerous electrical shock will result.
The national electric code requires the frame and external
electrically conductive parts of the generator be properly
connected to an approved earth ground. Local electrical
codes may also require proper grounding of the generator.
Consult with a local electrician for grounding requirements in
the area.
Do not use worn, bare, frayed or otherwise damaged electrical
cord sets with the generator.
Operate generator only on level surfaces and where it will not
be exposed to excessive, moisture, dirt, dust or corrosive
vapors.
Gasoline is highly FLAMMABLE and its vapors are
EXPLOSIVE. Do not permit smoking, open flames, sparks or
heat in the vicinity while handling gasoline, avoid spilling
gasoline on a hot engine. Comply with all laws regulating
storage and handling of gasoline.
Never add fuel while unit is running. Allow generator
and engine to cool entirely before adding fuel.
SAVE THESE INSTRUCTIONS- the manufacturer suggests
that these for safe operation be copied and posted near the unit’s
installation site. Safety should be stressed to all operators and
potential of this equipment.
Do not overfill the fuel tank; always allow
room for fuel expansion. If tank is over-filled, fuel can
overflow onto a hot engine and cause FIRE of an
EXPLOSION.
Never store generator with fuel in tank where gasoline vapors
might reach an open flame, spark or pilot light (as on a
furnace, water heater or clothes dryer). FIRE or EXPLOSION
may result.
3

Generator exhaust gases contain DEADLY carbon
monoxide gas. This dangerous gas, if breathed in sufficient
concentrations, can cause unconsciousness or even death.
Operate this equipment only in the open air where adequate
ventilation is available.
NEVER operate the generator indoors, in a
garage, near an open window, door, ventilated intake, crawl
space, other opening, or in an area that could accumulate
exhaust gas.
Allow at least five (5) feet, or greater, of
clearance on all sides of generator or damage could be done
to the unit. Never operate the unit inside any room or
enclosure.
*Never start or stop the unit with electrical loads connected to
receptacles AND with connected devices turned ON. Start the
engine and let it stabilize before connecting electrical loads.
Disconnect all electrical loads before shutting down the
generator.
* Do not insert objects through unit’s cooling slots.
*Never operate generator: in rain; indoors or in any enclosed
compartment; if connected electrical devices overheat; if electrical
output is lost; if engine or generator sparks; if flames or smoke
are observed while unit is running; if unit vibrates excessively.
4
WARNING
The engine exhaust from this product contains chemicals known to the
state fo california to cause cancer birth defects or other reproductive
harm.
WARNING
The product contains or emits chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm.
4

Study these SAFETY RULES carefully before installing,
operating or servicing this equipment. Become familiar with this
manual and with the unit. The generator can operate safely,
efficiently. Many accidents are caus ed by failing to follow
simple and fundamental rules or precautions.
The manufacturer cannot anticipate every possible circumstance
that might involve a hazard. The warnings in this manual, and on
tags and decals affixed to the unit are, therefore, not all inclusive,
if using a procedure, work method or operating technique that it is
safe for others. Also make sure the procedure, work method or
operating technique utilized does not render the generator
unsafe.
Despite the safe design of this generator,
operating this equipment imprudently, neglecting its
maintenance or being careless can cause possible injury or
death. Permit only responsible and capable persons to
operate or maintain this equipment.
Potentially lethal voltages are generated by these
machines. Ensure all steps are taken to render the machine
safe before attempting to work on the generator.
Parts of the generator are rotating and/or hot during
operation. Exercise care near running generators. Do not
touch hot surfaces such as the muffler. Severe burns can
occur on contact. Allow generator to cool before touching.
GENERAL HAZARDS
Never operate in an enclosed area or indoors.
For safely reasons, the manufacturer recommends that the
maintenance of this equipment is carried out by an authorized
dealer.
The engine exhaust fumes contain carbon monoxide, which
can be DEADLY. This dangerous gas, if breathed in sufficient
concentrations, can cause headaches, fatigue, DIZZINESS,
vomiting, confusion, SEISURES, fainting, unconsciousness
or even death. This exhaust system must be properly
maintained. Do nothing that might render the
5
5

exhaust system unsafe or in noncompliance with any local
codes and/or standards. A CO alarm is highly recommended.
zKeep hands, feet, clothing, etc., away from drive belts, fans,
and other moving or hot parts. Never remove any fan guard
while the unit is operating.
zAdequate, unobstructed flow of cooling and ventilating air is
critical to correct generator operation. Do not alter the
installation, as this can seriously affect safe operation of the
generator. The generator MUST be operated outdoors.
zWhen working on this equipment, remain alert at all times.
Never work on the generator regularly, and contact the
nearest authorized dealer for parts needing repair or
replacement.
zBefore performing any maintenance on the generator,
disconnect its battery cables to prevent accidental start up.
Disconnect the cable from the battery post indicated by a
NEGATIVE, NEG or (-) first. Reconnect that cable last.
zNever use the generator or any of its parts as a step. Stepping
on the unit can stress and break parts, and may result in
dangerous operating conditions from leaking exhaust gases,
fuel leakage, oil leakage, etc.
zDo not operate generator in the rain.
ELECTRICAL HAZARDS
*All generators covered by this manual produce dangerous
electrical voltages and can cause fatal electrical shock. Utility
power delivers extremely high and dangerous voltages as does
the generator when it is in operation. Avoid contact with bare
wires, terminals, connections, etc., while the unit is running.
Ensure all appropriate covers, guards and barriers are in place
before operating the generator. If word must be done around an
operating unit, stand on an insulated, dry surface to reduce shock
hazard.
*Do not handle any kind of electrical device while standing in
water, while barefoot, or while hands or feet are wet.
DANGEROUS ELECTRICAL SHOCK MAY RESULT.
*The national electrical code (NEC) requires the frame and
external electrically conductive parts of the generator to be
connected to an approved earth ground. Local electrical codes
6

also may require proper grounding of the generator electrical
system.
*In case of accident caused by electric shock, immediately shut
down the source of electrical power, if this is not possible, attempt
to free the victim from the live conductor. AVOID DIRECT
CONTACT WITH THE VICTIM. Use a non-conducting implement,
such as a rope or board, to free the victim from the live conductor.
If the victim is unconscious, apply first aid and get immediate
medical help.
*Never wear jewelry when working on this equipment. Jewelry
can conduct electricity resulting in electric shock, or may get
caught in moving components causing injury.
FIRE HAZARDS
*For fire safety, the generator must be operated and maintained
properly. Operation must always comply with applicable codes,
standards, laws and regulations. Adhere strictly to local, state and
national electrical and building codes. Comply with regulations
the occupational safety and health administration (OSHA) has
established. Also, ensure that the construction of the generator or
change controls which might create an unsafe operating
condition.
*Keep a fire extinguisher near the generator at all times.
Extinguishers rated “ABC” by the standby electric system, keep
the extinguisher properly charged and be familiar with its use. If
there are any questions pertaining to fire extinguishers, consult
the local fire department.
*Gasoline is extremely flammable. Avoid spilling gasoline on HOT
engine. Never add fuel while unit is running or hot. Do not overfill
the fuel tank. Always allow room for fuel expansion in fuel tank.
Wipe up spills immediately. Never fill fuel tank indoors.
EXPLOSION HAZARDS
*Do not smoke around the generator. Wipe up any fuel or oil spills
immediately. Ensure that no combustible materials are left on or
near the generator, as FIRE or EXPLOSION may result. Keeps
the area surrounding the generator clean and free from debris.
Gasoline is highly FLAMMABLE and extremely EXPLOSIVE.
7
7

STANDARDS INDEX
In the absence of pertinent standards, codes, regulations and
laws, the published information lasted below may be used as a
guideline for operation of this equipment. Always reference the
latest revision available for the standards listed.
1. NFPA NO. 70, NFPA HANDBOOK OF NATIONAL ELECTRIC
CODE.
2. Article X, NATIONAL BUILDING CODE, available form the
American insurance association, 85 John Street, New York, N,
Y.10038.
3. AGRICULTURAL WIRING HANDBOOK, available from the
food and energy council, 909 university avenue, Columbia,
MO65201
4. ASAE EP-3634, INSTALLATION AND MAINTENANCE OF
FARM STANDBY ELECTRICAL SYSTEMS, available from
the American society of agricultural engineers, 2950 Niles
road, St. Joseph,MI49085
5. NFPA No. 30, FLAMMABLE AND COMBUSTIBLE LIQUIDS
CODE.
1.1UNPACKING
* Remove all packaging material.
* Remove separate accessory box.
* remove the generator from carton.
1.1.1 ACCESSORY BOX
Check all contents. If any parts are missing or damaged, locate
an authorized dealer at 1-888-545-7788.
* 1-Owner’s manual
*2-Wheels
*
1-Handle assembly
*1-Handle bracket
*1-Wheel axle
*1-Hardware bag (containing the following):
*2-Rubber bumpers 7-M6 flange nuts
*2-Bumper brackets 2-Cotter pins
*2-M12 flat washers 2-Hubs
*
5-M6-1 x 40 flange bolts 2-M6-1.0Χ16 flange bolts
88

1.2 ASSEMBLY
The generator requires some assembly prior to using it ,if
problems arise when assembling the generator, please call the
AMICO Generator Help Line
at 1-888-545-7788.
1.2.1 ASSEMBLING THE ACCESSORY KIT
The wheels are designed to the unit to greatly improve the
portability of the generator.
The wheels are not intended for over-the-road-use.
1. Refer to figure 1 to install the wheels as shown.
*slide the axle through the frame brackets.
*slide on the hub, wheel and flat washer, then insert the cotter
pin through the wheel axle hole.
2. Refer to figure 1 to install the wheel bumpers as shown.
*Insert an M6 bolt through the frame brackets.
*Slide on the hub, wheel and flat washer,and then insert the
cotter pin through the wheel axle hole.
*Bend the cotter pin tabs outward to lock the pin in place.
3. Refer to figure 2 to install the handle assembly as shown.
*Insert the handle bracket onto the generator frame and
secure with two M6 bolts and to M6 flange nuts.
*Align the handle assembly holes with the handle bracket
holes and secure with one M6 bolt and one M6 flange nut.
Figure 1- Wheel Assembly
9
4. Refer to figure 1 to install the battery as shown.
Axle
Gasket
B type pin
Flange bolt
Battery support
Battery
Butterfly nut
Flange nut
Flange bolt
Handle pipe
Handle plastic nut
Flange bolt
Flange nut
Support
Rubber pad
Stud nut

Figure 2-Handle Kit
2.1 KNOW THE GENERATOR
Read the owner’s manual and safely rules before operating
this generator.
Compare the generator to figures 3 through 5 to become
familiarized with the locations of various controls and adjustments.
Save this manual for future reference.
1. 120 Volt AC,20 amp, duplex receptacle-supplies electrical
power for the operation of 120 volt AC.20 amp, single-phase,
60hz electrical lighting, appliance, tool and motor loads.
2. 240 Volt AC,30 amp, twist lock receptacle- supplies electrical
power for the operation of 240 volt AC.30 amp, single-phase,
60hz electrical lighting, appliance, tool and motor loads.
3. Circuit breakers (AC) – each receptacle is provided with a
push-to-reset circuit breaker to protect the generator against
electrical overload.
4. Air filter- filters intake air as it is drawn into the engine.
5. Choke knob-used when starting a cold engine.
6. Fuel tank- tank holds 6.42 U.S gallons of fuel.
7. Grounding lug – ground the generator to an approved earth
ground here. See “Grounding the generator” for details.
8. ON/OFF key switch- controls the operation of the generator.
9. Muffler-quiets the engine.
10.Handle-pivot and retract for storage.
11.Gas cap- fuel fill location.
12.Fuel gauge- shows fuel level in tank.
10

13.Oil check/fill- check and fill oil here.
14.Recoil start- use to start engine manually.
15.Fuel shut off- valve between fuel tank and carburetor.
16.Oil drain plug- used to drain engine oil.
17.Spark arrestor- reduces fire hazard by containing sparks.
18. Spark plug
19. Wheel
Figure 3– control panel
Figure 4 – generator controls
Figure 5 – generator controls
11
8
3
1
2
12
11
13
16
14
9
10
6
4
5
15
16
18
11

2.2 CORD SETS AND CONNECTION PLUGS
2.2.1 120VAC, 20 AMP, DUPLEX RECEPTACLE.
This is a 120 volt outlet protected against overload by a 13.5 amp
push - to - reset circuit breaker 13.5 amps of current may
be drawn from each socket; however, total power drawn must be
kept within data plate ratings. Use only high quality, well insulated,
3-wire grounded cord sets rated for 125 volts at 20 amps (or
greater).
2.3 HOW TO USE THE GENERATOR
If there are any problems operating the generator, please call the
generator helpline at 1-888-545-7788
Using a generator indoors WILL KILL YOU IN
MINUTES. Exhaust contains carbon monoxide, a poison gas you
cannot see or smell.
NEVER use in the home, or in partly enclosed far from open
windows, doors, vents, and in an area that will not
accumulate deadly exhaust gas.
2.3.1 GROUNDING THE GENERATOR
The national electrical code requires that the frame and
external electrically conductive parts of this generator be
properly connected to an approved earth ground (figure
7).local electrical codes may also require proper grounding of the
unit. For that purpose, connecting a no. 10 AWG (American wire
gauge) stranded copper wire to the grounding rod (electrode)
provides adequate protection against electrical shock. However,
local codes may vary widely. Consult with a local electrician
for grounding requirements in the area.
12
12

Figure 7- grounding the generator
Proper grounding of the generator will help prevent
electrical shock in the event of a ground fault condition in the
generator or in connected devices. Proper grounding also helps
dissipate static electricity, which often builds up in ungrounded
devices.
2.3.2 CONNECTING ELCTRICAL LOADS
Do not connect 240 volt loads to 120 volt receptacles. Do not
connect 3-phase loads to the generator. Do not connect 50 Hz
loads to the generator.
*let engine stabilize and warm up for a few minutes after starting.
*plug in and turn on the desired 120 or 240 volt AC. Single phase,
60 Hz electrical loads.
*add up the rated watts (or amps) of all loads to be connected at
one time. This total should not be greater than (a) the rated
wattage/amperage capacity of the generator or (b) circuit
breaker rating of the receptacle supplying the power. See “don’t
overload the generator”.
2.4 DON’T OVERLOAD THE GENERATOR
Overloading a generator in excess of its rated wattage capacity
can result in damage to the generator and to connected electrical
devices. Observe the following to prevent overloading the unit:
*Add up the total wattage of all electrical devices to be connected
at one time. This total should NOT be greater than the
generator’s wattage capacity.
*The rated wattage of lights can be taken from light bulbs. The
rated wattage of tools, appliances and motors can usually be
13
13

found on a data label or decal affixed to the device.
*If the appliance, tool or motor does not give wattage, multiply
volts times ampere rating to determine watts (volts x amps =
watts).
*Some electric motors, such as induction types, require about
three times more watts of power for starting than for running.
This surge of power lasts only a few seconds when starting such
motors. Make sure to allow for high starting wattage when
selecting electrical devices to connect to the generator.
1. Figure the watts needed to start the largest motor.
2. Add to that figure the running watts of all other connected
loads.
The wattage reference guide is provided to assist in determining
how many items the generator can operate at one time.
All figures are approximate. See data label
on appliance for wattage requirements.
2.5 WATTAGE REFERENCE GUIDE
Device…………………………………………………..running watts
*Air conditioner (12,000 Btu)…………………………………...1700
*Air conditioner (24,000 Btu)…………………………………...3800
*Air conditioner (40,000
Btu)……………………………………6000
Battery charger (20 Amp)………………………………………...500
Belt sander (3”)……………………………...…………………...1000
Chain saw………………………………………………………..1200
Circular saw(6-1/2”)………………………………………800to1000
*Clothes dryer (electric)…………………………………………5750
*Clothes dryer
(gas)……………………………………………….700
*Clothes washer………………………………………………….1150
Coffeemaker……………………………………………………..1750
*Compressor（1hp）……….…...…...…………...………
……..2000
*Compressor
(3/4hp)…………………………………….………1800
*Compressor(1/2hp)………………………………….…………1400
Curling iron………………………………………………………..700
*Dehumidifier……………………………………………………...650
Disc sander (9”)………………………………………………….1200
Edge trimmer……………………………………………………...500
Electric blanket……………………………………………………400
14
14

Electric nail gun………………………………………………….1200
Electric range (per element)………………………….………...1500
Electric skillet……………………………….……………………1250
*Freezer……………………………………………………………700
*Furnace fan (3/5hp)………………………………………………875
*Garage door opener…………………………………….500 to 750
Hair dryer………………………………………………………...1200
Hand drill…………………………………………………250 to 1100
Hedge trimmer…………………………………………………….450
Impact wrench…………………………………………………….500
Iron…………………………………………………….………….1200
*jet pump……………………………………………….………….800
Lawn mower…………………………………………….………..1200
Light bulb………………………………………………..………….100
Microwave oven………………………………………….700 to 1000
*Milk cooler…………………………………………..…………...1100
Oil burner on furnace…………………….…………….…..….....300
Oil fired space heater
(140,000 Btu)………………….…………400
Oil fired space heater (85,000 Btu)………………….………….225
Oil fired space heater （30,000 Btu）……………………………150
*Paint sprayer, airless (1/3hp)…………………………………..600
Paint sprayer, airless (handheld)………………………………..150
Radio………………………………………………………...50 to 200
*Refrigerator……………………………………………………….700
Slow cooker………………………………………………………..200
*Submersible pump （1-1/2 hp）……………………………….2800
*Submersible pump (1hp)………………..…...………………..2000
*Submersible pump (1/2 hp)……………………...…...……….1500
*Sump pump……….………………………………….....800 to 1050
*Table saw (10”)….…………………………………….1750 to 2000
Television.…………….……………………………………200 to 500
Toaster………………..…………………………………1000 to 1650
Weed trimmer……………………………………...……………...500
*Allow 3 times the listed watts for starting these devices
2.6 BEFORE STARTING THE GENRATOR
Prior to operating the generator, engine oil and gasoline will need
to be added, as follows:
15
15

2.6.1 ADDING ENGINE OIL
All oil should meet minimum American petroleum institute (API)
service class SJ, SL or better. Use no special additives. Select
the oil’s viscosity grade according to the expected operating
temperature (also see chart).
*Above 40°F，use SAE 30
*Below 40°F and down to 10°F, use 10W-30
*Below 10°F, use synthetic 5W-30
Any attempt to crank or start the engine
before it has been properly serviced with the recommended
oil may result in an engine failure.
*Place generator on a level surface.
*Clean area around oil fill and remove oil fill cap and dipstick.
*Wipe dipstick clean.
*Slowly fill engine with oil through the oil fill opening until it
reaches the full mark on the dipstick. Stop filling occasionally to
check oil level. Be careful not to over fill.
*Install oil cap and finger tighten securely.
*Check engine oil level before starting each time thereafter.
2.6.2 ADDING GASOLINE
Never fill fuel tank indoors. Never fill fuel tank
when engine is running or hot. Allow engine to cool entirely
before filling fuel tank. Avoid a cigarette or smoke when filling the
fuel tank. Gasoline is highly FLAMMABLE and its vapors are
16
16

EXPLOSIVE.
DO not overfill the fuel tank. Always leave room
for fuel expansion. If the fuel tank is overfilled, fuel can overflow
onto a HOT engine and cause FIRE or EXPLOSION.
*use regular UNLEADED gasoline with the generator engine. Do
not use any gasoline with more than 10% added ethanol, and
never use E85 gasoline. Do not mix oil with gasoline.
*Clean area around fuel fill cap, remove cap.
*Slowly add unleaded regular gasoline to fuel tank. Fill to bottom
of screen filter. Be careful not to overfill (figure 8).
Figure 8 – fuel tank
IMPORTANT: It is important to prevent gum deposits from
forming in fuel system parts such as the carburetor, fuel hose or
tank during storage. Alcohol-blended fuels (called gasohol,
ethanol or methanol) can attract moisture, which leads to
separation and formation of acids during storage. Acidic gas can
damage the fuel system of an engine while in storage. To avoid
engine problems, the fuel system should be emptied before
storage of 30 days or longer. See the “Storage” section. Never
use engine or carburetor cleaner products in the fuel tank as
permanent damage may occur.
2.7 TO START THE GENERATOR
Never start or stop engine with electrical
devices plugged into the receptacles AND devices turned on.
*Unplug all electrical loads from the unit’s receptacles before
starting the engine.
17