Amico Sparrow Original operating instructions

1
Light-duty Monitor Arm
Quick Installation and Adjustment Instructions
LMA Monitor Arm
1. Monitor Mounting Adapter
VESA LCD mount
2. Monitor Head - Rotation
Monitor rotation adjustment
3. Counter Balance
Used to adjust for zero movement
4. Arm Rotation Adjustment
Used to adjust ease of rotation
5. Extension Arm *
LMA extension arm shown
6. Extension Arm Rotation Adjustment
Used to adjust ease of rotation
7. Mounting Adapter
MON adapter shown for MRS rail
* If requested
Medical Facility Responsibility
Installation Tools
2.5 mm, 1/8", 5 mm, & 6 mm Hex Keys
1/2" (12.7 mm) Socket Wrench
#3 Phillips Head Screwdriver
!
WARNING: It is the responsibility of the end user to ensure all aspects of the installation are covered by following the full
manual at: https://www.amico.com/sites/default/files/products/amico-aa-lma-light-duty-monitor-arm-manual.pdf
Mounting to MRS (Monitor Rail System) Mounting to VRS (Vertical Rail System)
1. Assemble LMA to X-LMA-(MON/MON-B)-ADA by placing LMA onto X-LMA(MON/MON-
B)-ADA and securing with the SCREW through WASHER, X-LMA-(MON/MON-B)-ADA,
LMA, and into CAP, using #3 Philips Head screwdriver (as shown in Figure 1 on the
left below).
2. Slide X-LMA-(MON/MON-B)-ADA into the MRS RAIL (as shown in Figure 1 on the right
below).
3. Once the arm is positioned at the desired height, tighten 2x of the parts labeled
H-SSCP-1420-05 in Figure 1 below with a 1/8" (3.2 mm) Hex key.
1. Remove the top X-GTA-KNOB/X-GTA-KNOB-B and the attached HR-CONV-PIN.
(Figure 2)
2. Place LMA-__-(_____)-__onto X-LMA-VRS-ADA/X-LMA-VRS-B-ADA and secure by
inserting SCREW (part of X-LMA-01-01) through WASHER (part of X-LMA-01-01), X-LMA-
VRS-ADA/X-LMA-VRS-B-ADA, LMA-__-(_____)-__, and into CAP (part of X-LMA-01-01).
(Figure 2)
3. Replace the TOP HR-CONV-PIN and X-GTA-KNOB/X-GTA-KNOB-B. (Figure 2)
4. Turn 2x X-GTA-KNOB-X-GTA-KNOB-B to loosen 2x HR-CONV-PIN. Tilt and guide the 2x
HR-CONV-PIN into the opening of the VRS RAIL. (Figure 3)
5. Ensure the flange on the X-SSM-VERT-ADA is properly aligned with the VRS RAIL.
Position to desired height before tightening 2x X-GTA-KNOB/X-GTA-KNOB-B. (Figure 3)
6. Lock the 2x X-GTA-KNOB/X-GTA-KNOB-B with 2x H-1420-LNUT-NYL using a 1/2"
(12.7 mm) socket wrench and cover with 2x H-CAP-14-B. (Figure 3)
SCREW
(PART OF X-LMA-01-01)
LMA-__-(_____)-__
WASHER
(PART OF X-LMA-01-01)
X-LMA-MON-ADA/
X-
LMA-MON-B-ADA
X-
LMA-MON-ADA/
X-LMA-MON-B-ADA
2 X H-SSC 05
P-1420-
X-
HR-CONV-PIN
SSM-VERT-ADA
Figure 3
2 X H-CAP-14-B
2 X H-1420-LNUT-NYL
GTA-KNOB/
X-
X-GTA-KNOB-B
Figure 1
Figure 2
2 X HR-CONV-PIN
X-GTA-KNOB/
GTA-KNOB-B
X-
2 X H-CAP-14-B
SCREW
(PART OF X-LMA-01-01)
WASHER
(PART OF X-LMA-01-01)
CAP
(PART OF X-LMA-01-01)
AD
X-LMA-VRS-
X-
LMA-VRS-B-ADA
X-
TOP X-GTA-KNOB/
X-GTA-KNOB-B
TOP HR-CONV-PIN
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Tel: [phone]
Toll Free: 1.877.264.2697 (T)
PROJECTION
SCREW
(PART OF X-LMA-01-01)
LMA-__-(_____)-__
WASHER
(PART OF X-LMA-01-01)
X-LMA-MON-ADA/
X-
LMA-MON-B-ADA
X-
LMA-MON-ADA/
X-LMA-MON-B-ADA
2 X H-SSC 05
P-1420-
X-
HR-CONV-PIN
SSM-VERT-ADA
Figure 3
2 X H-CAP-14-B
2 X H-1420-LNUT-NYL
GTA-KNOB/
X-
X-GTA-KNOB-B
Figure 1
Figure 2
2 X HR-CONV-PIN
X-GTA-KNOB/
GTA-KNOB-B
X-
2 X H-CAP-14-B
SCREW
(PART OF X-LMA-01-01)
WASHER
(PART OF X-LMA-01-01)
CAP
(PART OF X-LMA-01-01)
AD
X-LMA-VRS-
X-
LMA-VRS-B-ADA
X-
TOP X-GTA-KNOB/
X-GTA-KNOB-B
TOP HR-CONV-PIN
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Tel: [phone]
Toll Free: 1.877.264.2697 (T)
PROJECTION
CAP
(PART OF X-LMA-01-01)
X-LMA-MON-ADA/
X-LMA-MON-B-ADA
WASHER
(PART OF X-LMA-01-01)
LMA-__-(_____)-__
X-LMA-MON-ADA/
X-LMA-MON-B-ADA
MRS RAIL
2x
H-SSCP-1420-05
SCREW
(PART OF X-LMA-01-01)
SCREW
(PART OF X-LMA-01-01)
LMA-__-(_____)-__
WASHER
(PART OF X-LMA-01-01)
X-LMA-MON-ADA/
X-
LMA-MON-B-ADA
X-
LMA-MON-ADA/
X-LMA-MON-B-ADA
2 X H-SSC 05
P-1420-
X-
HR-CONV-PIN
SSM-VERT-ADA
Figure 3
2 X H-CAP-14-B
2 X H-1420-LNUT-NYL
GTA-KNOB/
X-
X-GTA-KNOB-B
Figure 1
Figure 2
2 X HR-CONV-PIN
X-GTA-KNOB/
GTA-KNOB-B
X-
2 X H-CAP-14-B
SCREW
(PART OF X-LMA-01-01)
WASHER
(PART OF X-LMA-01-01)
CAP
(PART OF X-LMA-01-01)
AD
X-LMA-VRS-
X-
LMA-VRS-B-ADA
X-
TOP X-GTA-KNOB/
X-GTA-KNOB-B
TOP HR-CONV-PIN
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Tel: [phone]
Toll Free: 1.877.264.2697 (T)
PROJECTION
CAP
(PART OF X-LMA-01-01)
TOP HR-CONV-PIN
TOP X-GTA-KNOB/
X-GTA-KNOB-B
X-LMA-VRS-ADA/
X-LMA-VRS-B-ADA
WASHER
(PART OF X-LMA-01-01)
SCREW
(PART OF X-LMA-01-01)
SCREW
(PART OF X-LMA-01-01)
LMA-__-(_____)-__
WASHER
(PART OF X-LMA-01-01)
X-LMA-MON-ADA/
X-
LMA-MON-B-ADA
X-
LMA-MON-ADA/
X-LMA-MON-B-ADA
2 X H-SSC 05
P-1420-
X-
HR-CONV-PIN
SSM-VERT-ADA
Figure 3
2 X H-CAP-14-B
2 X H-1420-LNUT-NYL
GTA-KNOB/
X-
X-GTA-KNOB-B
Figure 1
Figure 2
2 X HR-CONV-PIN
X-GTA-KNOB/
GTA-KNOB-B
X-
2 X H-CAP-14-B
SCREW
(PART OF X-LMA-01-01)
WASHER
(PART OF X-LMA-01-01)
CAP
(PART OF X-LMA-01-01)
AD
X-LMA-VRS-
X-
LMA-VRS-B-ADA
X-
TOP X-GTA-KNOB/
X-GTA-KNOB-B
TOP HR-CONV-PIN
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Tel: [phone]
Toll Free: 1.877.264.2697 (T)
PROJECTION
X-GTA-KNOB/
X-GTA-KNOB-B
X-GTA-KNOB/
X-GTA-KNOB-B
2x H-CAP-14-B
2x H-CAP-14-B
HR-CONV-PIN
X-SSM-VERT-ADA
2x H-1420-LNUT-NYL
2x HR-CONV-PIN
Figure 1 Figure 2 Figure 3
SCREW
(PART OF X-LMA-01-01)
LMA-__-(_____)-__
WASHER
(PART OF X-LMA-01-01)
X-LMA-MON-ADA/
X-
LMA-MON-B-ADA
X-
LMA-MON-ADA/
X-LMA-MON-B-ADA
2 X H-SSC 05
P-1420-
X-
HR-CONV-PIN
SSM-VERT-ADA
Figure 3
2 X H-CAP-14-B
2 X H-1420-LNUT-NYL
GTA-KNOB/
X-
X-GTA-KNOB-B
Figure 1
Figure 2
2 X HR-CONV-PIN
X-GTA-KNOB/
GTA-KNOB-B
X-
2 X H-CAP-14-B
SCREW
(PART OF X-LMA-01-01)
WASHER
(PART OF X-LMA-01-01)
CAP
(PART OF X-LMA-01-01)
AD
X-LMA-VRS-
X-
LMA-VRS-B-ADA
X-
TOP X-GTA-KNOB/
X-GTA-KNOB-B
TOP HR-CONV-PIN
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Tel: [phone]
Toll Free: 1.877.264.2697 (T)
PROJECTION
13
5
7
24
6
Quick Setup

Amico Accessories Inc. | 85 Fulton Way, Richmond Hill, ON L4B 2N4, Canada | www.amico.com
Toll Free Tel: [phone] | Tel: [phone] | Fax: [phone] | Email: [email protected]
Light-duty Monitor Arm
Quick Installation and Adjustment Instructions
2
Quick Adjustment Reference
Rotation (LMA Side to Side) Head Tilt
To adjust the tension on the movement of the arm, tighten or loosen the SCREW in the
appropriate joints as shown in the detailed view below using a 2.5 mm Hex key.
Tighten or loosen the appropriate SCREW as shown in Figure 5 to adjust the monitor’s
position accordingly. For swivelling, use a 5 mm Hex key. For tilting, use a 6 mm Hex key.
!
WARNING: Do not loosen the TOP SCREW. Doing so may cause the head assembly to
fall off.
SCREW
(PART OF X-LMA-01-01)
LMA-__-(_____)-__
WASHER
(PART OF X-LMA-01-01)
X-LMA-MON-ADA/
X-
LMA-MON-B-ADA
X-
LMA-MON-ADA/
X-LMA-MON-B-ADA
2 X H-SSC 05
P-1420-
X-
HR-CONV-PIN
SSM-VERT-ADA
Figure 3
2 X H-CAP-14-B
2 X H-1420-LNUT-NYL
GTA-KNOB/
X-
X-GTA-KNOB-B
Figure 1
Figure 2
2 X HR-CONV-PIN
X-GTA-KNOB/
GTA-KNOB-B
X-
2 X H-CAP-14-B
SCREW
(PART OF X-LMA-01-01)
WASHER
(PART OF X-LMA-01-01)
CAP
(PART OF X-LMA-01-01)
AD
X-LMA-VRS-
X-
LMA-VRS-B-ADA
X-
TOP X-GTA-KNOB/
X-GTA-KNOB-B
TOP HR-CONV-PIN
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Tel: [phone]
Toll Free: 1.877.264.2697 (T)
PROJECTION
DETAILED VIEW
<360°
<360°
SCREW
(PART OF X-LMA-01-01)
LMA-__-(_____)-__
WASHER
(PART OF X-LMA-01-01)
X-LMA-MON-ADA/
X-
LMA-MON-B-ADA
X-
LMA-MON-ADA/
X-LMA-MON-B-ADA
2 X H-SSC 05
P-1420-
X-
HR-CONV-PIN
SSM-VERT-ADA
Figure 3
2 X H-CAP-14-B
2 X H-1420-LNUT-NYL
GTA-KNOB/
X-
X-GTA-KNOB-B
Figure 1
Figure 2
2 X HR-CONV-PIN
X-GTA-KNOB/
GTA-KNOB-B
X-
2 X H-CAP-14-B
SCREW
(PART OF X-LMA-01-01)
WASHER
(PART OF X-LMA-01-01)
CAP
(PART OF X-LMA-01-01)
AD
X-LMA-VRS-
X-
LMA-VRS-B-ADA
X-
TOP X-GTA-KNOB/
X-GTA-KNOB-B
TOP HR-CONV-PIN
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Tel: [phone]
Toll Free: 1.877.264.2697 (T)
PROJECTION
SCREW
(PART OF X-LMA-01-01)
LMA-__-(_____)-__
WASHER
(PART OF X-LMA-01-01)
X-LMA-MON-ADA/
X-
LMA-MON-B-ADA
X-
LMA-MON-ADA/
X-LMA-MON-B-ADA
2 X H-SSC 05
P-1420-
X-
HR-CONV-PIN
SSM-VERT-ADA
Figure 3
2 X H-CAP-14-B
2 X H-1420-LNUT-NYL
GTA-KNOB/
X-
X-GTA-KNOB-B
Figure 1
Figure 2
2 X HR-CONV-PIN
X-GTA-KNOB/
GTA-KNOB-B
X-
2 X H-CAP-14-B
SCREW
(PART OF X-LMA-01-01)
WASHER
(PART OF X-LMA-01-01)
CAP
(PART OF X-LMA-01-01)
AD
X-LMA-VRS-
X-
LMA-VRS-B-ADA
X-
TOP X-GTA-KNOB/
X-GTA-KNOB-B
TOP HR-CONV-PIN
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Tel: [phone]
Toll Free: 1.877.264.2697 (T)
PROJECTION
TOP SCREW
Figure 4 Figure 5
Counter Balance Cable Management
If the monitor does not hold its position or is too resistant, adjust the SCREW clockwise for
heavier loads and counter-clockwise for lighter loads for counter-balance as shown in the
DETAILED VIEW below in Figure 6, with a 5 mm Hex key.
SCREW
(PART OF X-LMA-01-01)
LMA-__-(_____)-__
WASHER
(PART OF X-LMA-01-01)
X-LMA-MON-ADA/
X-
LMA-MON-B-ADA
X-
LMA-MON-ADA/
X-LMA-MON-B-ADA
2 X H-SSC 05
P-1420-
X-
HR-CONV-PIN
SSM-VERT-ADA
Figure 3
2 X H-CAP-14-B
2 X H-1420-LNUT-NYL
GTA-KNOB/
X-
X-GTA-KNOB-B
Figure 1
Figure 2
2 X HR-CONV-PIN
X-GTA-KNOB/
GTA-KNOB-B
X-
2 X H-CAP-14-B
SCREW
(PART OF X-LMA-01-01)
WASHER
(PART OF X-LMA-01-01)
CAP
(PART OF X-LMA-01-01)
AD
X-LMA-VRS-
X-
LMA-VRS-B-ADA
X-
TOP X-GTA-KNOB/
X-GTA-KNOB-B
TOP HR-CONV-PIN
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Tel: [phone]
Toll Free: 1.877.264.2697 (T)
PROJECTION
CONNECT CABLES
INSERT CABLES
INSERT CABLES
SCREW
(PART OF X-LMA-01-01)
LMA-__-(_____)-__
WASHER
(PART OF X-LMA-01-01)
X-LMA-MON-ADA/
X-
LMA-MON-B-ADA
X-
LMA-MON-ADA/
X-LMA-MON-B-ADA
2 X H-SSC 05
P-1420-
X-
HR-CONV-PIN
SSM-VERT-ADA
Figure 3
2 X H-CAP-14-B
2 X H-1420-LNUT-NYL
GTA-KNOB/
X-
X-GTA-KNOB-B
Figure 1
Figure 2
2 X HR-CONV-PIN
X-GTA-KNOB/
GTA-KNOB-B
X-
2 X H-CAP-14-B
SCREW
(PART OF X-LMA-01-01)
WASHER
(PART OF X-LMA-01-01)
CAP
(PART OF X-LMA-01-01)
AD
X-LMA-VRS-
X-
LMA-VRS-B-ADA
X-
TOP X-GTA-KNOB/
X-GTA-KNOB-B
TOP HR-CONV-PIN
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Tel: [phone]
Toll Free: 1.877.264.2697 (T)
PROJECTION
Figure 6 Figure 7
SCREW
(PART OF X-LMA-01-01)
LMA-__-(_____)-__
WASHER
(PART OF X-LMA-01-01)
X-LMA-MON-ADA/
X-
LMA-MON-B-ADA
X-
LMA-MON-ADA/
X-LMA-MON-B-ADA
2 X H-SSC 05
P-1420-
X-
HR-CONV-PIN
SSM-VERT-ADA
Figure 3
2 X H-CAP-14-B
2 X H-1420-LNUT-NYL
GTA-KNOB/
X-
X-GTA-KNOB-B
Figure 1
Figure 2
2 X HR-CONV-PIN
X-GTA-KNOB/
GTA-KNOB-B
X-
2 X H-CAP-14-B
SCREW
(PART OF X-LMA-01-01)
WASHER
(PART OF X-LMA-01-01)
CAP
(PART OF X-LMA-01-01)
AD
X-LMA-VRS-
X-
LMA-VRS-B-ADA
X-
TOP X-GTA-KNOB/
X-GTA-KNOB-B
TOP HR-CONV-PIN
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Tel: [phone]
Toll Free: 1.877.264.2697 (T)
PROJECTION
SCREW
(PART OF X-LMA-01-01)
LMA-__-(_____)-__
WASHER
(PART OF X-LMA-01-01)
X-LMA-MON-ADA/
X-
LMA-MON-B-ADA
X-
LMA-MON-ADA/
X-LMA-MON-B-ADA
2 X H-SSC 05
P-1420-
X-
HR-CONV-PIN
SSM-VERT-ADA
Figure 3
2 X H-CAP-14-B
2 X H-1420-LNUT-NYL
GTA-KNOB/
X-
X-GTA-KNOB-B
Figure 1
Figure 2
2 X HR-CONV-PIN
X-GTA-KNOB/
GTA-KNOB-B
X-
2 X H-CAP-14-B
SCREW
(PART OF X-LMA-01-01)
WASHER
(PART OF X-LMA-01-01)
CAP
(PART OF X-LMA-01-01)
AD
X-LMA-VRS-
X-
LMA-VRS-B-ADA
X-
TOP X-GTA-KNOB/
X-GTA-KNOB-B
TOP HR-CONV-PIN
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Tel: [phone]
Toll Free: 1.877.264.2697 (T)
PROJECTION
DETAILED VIEW
AA-QG-LMA-LIGHT-DUTY-MONITOR-ARM-SPARROW 05.01.2015