AMIMON AMN41012 User manual
Amimon Ltd. 26 Zarhin St. Raanana, Israel. Tel: +972-9-9629222 www.amimon.com
2017 © All rights reserved to Amimon ltd. Proprietary and Confidential
Confidentiality is requested
Table of Contents
Table of Contents ....................................................................... 2
Important Notice......................................................................... 3
Revision History.......................................................................... 4
Safety Instructions ..................................................................... 5
Introduction ................................................................................ 6
Product Description.................................................................... 8
(1) LED behaviors .................................................................................................10
(2) Board-to-Board Connector ...........................................................................11
Installation ................................................................................ 12
S
Y
Z
0
1
0
M
Amimon Ltd. 26 Zarhin St. Raanana, Israel. Tel: +972-9-9629222 www.amimon.com
2017 © All rights reserved to Amimon ltd. Proprietary and Confidential
Confidentiality is requested
Important Notice
AMIMON Ltd. reserves the right to make corrections, modifications, enhancements, improvements, and
other changes to its products and services at any time and to discontinue any product or service without
notice. Customers should obtain the latest relevant information before placing orders and should verify
that such information is current and complete. All products are sold subject to AMIMON's terms and
conditions of sale supplied at the time of order acknowledgment.
AMIMON warrants performance of its hardware products to the specifications applicable at the time of
sale in accordance with AMIMON's standard warranty. Testing and other quality control techniques are
used to the extent AMIMON deems necessary to support this warranty. Except where mandated by
government requirements, testing of all parameters of each product is not necessarily performed.
AMIMON assumes no liability for applications assistance or customer product design. Customers are
responsible for their products and applications using AMIMON components. To minimize the risks
associated with customer products and applications, customers should provide adequate design and
operating safeguards.
AMIMON does not warrant or represent that any license, either express or implied, is granted under any
AMIMON patent right, copyright, mask work right, or other AMIMON intellectual property right relating to
any combination, machine, or process in which AMIMON products or services are used. Information
published by AMIMON regarding third-party products or services does not constitute a license from
AMIMON to use such products or services or a warranty or endorsement thereof. Use of such
information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from AMIMON under the patents or other intellectual property of AMIMON.
Reproduction of information in AMIMON data books or data sheets is permissible only if reproduction is
without alteration and is accompanied by all associated warranties, conditions, limitations, and notices.
Reproduction of this information with alteration is an unfair and deceptive business practice. AMIMON is
not responsible or liable for such altered documentation.
Resale of AMIMON products or services with statements different from or beyond the parameters stated
by AMIMON for that product or service voids all express and any implied warranties for the associated
AMIMON product or service and is an unfair and deceptive business practice. AMIMON is not
responsible or liable for any such statements.
All company and brand products and service names are trademarks or registered trademarks of their
respective holders.
Please refer to the regulatory guide regarding regulatory information that needs to be on the labeling
and user manual.
Amimon Ltd. 26 Zarhin St. Raanana, Israel. Tel: +972-9-9629222 www.amimon.com
2017 © All rights reserved to Amimon ltd. Proprietary and Confidential
Confidentiality is requested
Safety Instructions
When operating this equipment, read and follow all the instructions in this
manual
Do not open unit
Do not block air ventilation
Use only accessories/batteries/ power supplies provided, specified or
recommended by AMIMON.
When devices are switched on keep away at least 20 cm from your body.
People with pacemakers should ALWAYS keep the device at the listed distance
from their pacemaker when turned ON. Should you have any reason to suspect
that interference is taking place, you should turn your device OFF.
Do not expose to moisture, excessive heat or fire
Keep away from water and other liquids
Do not power the device when it is wet or damp
Use the mains plug to disconnect the apparatus.
Clean with a dry cloth only
Unplug this apparatus during lightning storms or when unused for long periods
of time
To reduce the risk of fire or electric shock, refer servicing to qualified service
personnel
Please avoid electrostatic discharge from the antenna ports for proper
operation
WARNING –do not touch. Please beware of hot surfaces of the devices
and wait until it cools off
Please avoid electrostatic discharge from the antenna ports for proper
operation
Keep these instructions in a safe and accessible place for future use.
Declared maximum operating temperature: +50°C
Explanation of graphical symbols:
High Voltage Sign: warns the user of the presence of uninsulated
"dangerous voltage" within the product enclosure, which may be of
sufficient magnitude to constitute a risk.
General Warning Sign: warns the user of the presence of
important operating and maintenance (servicing) instructions in the
product manual.
Amimon Ltd. 26 Zarhin St. Raanana, Israel. Tel: +972-9-9629222 www.amimon.com
2017 © All rights reserved to Amimon ltd. Proprietary and Confidential
Confidentiality is requested
Introduction
The AMN41012 and AMN42012 are wireless video system comprising of a video transmitter
and video receiver modules, that operate at the 5GHz unlicensed band.
It is are based on AMIMON's Professional chipset that consist of the AMN2130 and AMN2230
baseband receiver and the MAXIM 2850 and 2851 ICs, providing the ultimate solution for 4K
Video transmission. The perfect video, audio quality, the high robustness and the invisible
latency of the wireless system are unmatched by any other wireless technology and presents
a true alternative to cable. The system transmits uncompressed video and audio streams
wirelessly and thus simplifies and eliminates system issues, such as: lip-sync, large buffers
and other burdens like retransmissions or error propagation.
System Technical Specifications:
Table 1: AMN41012 - Technical Specifications
AMN41012
Frequency
Control:
Non-DFS Frequencies :
5.150~ 5.250 GHz for EU
5.150 ~ 5.250 GHz and 5.725~5.825 GHz for US
DFS Frequencies (used only in Aerial mode):
5.250-5.350 GHz and 5.470 ~ 5.725 GHz for EU
5.250-5.330 GHz and 5.470 ~ 5.725 GHz for US
5.250-5.350 GHz and 5.470 ~ 5.6GHz and 5.650 ~ 5.710 GHz for Canada
SRD Frequencies (EU):
5.725 ~ 5.875 GHz for EU
Antenna:
Total connectors: 2 or 4
2 or 4 transmitting ports of which 2 ports also act as receiving ports using diversity
through a single receive chain
External using on-board UFL Connectors: 2dBi or 5dBi omni Antenna gain
Environment:
Operational: -20 ÷ 50°C, 10 ÷ 90% humidity
Storage: -20 ÷ 55° C, 10% ÷ 90% humidity
Voltage:
5VDC ±10%
Size:
L: 70.0mm x W: 56.1mm x H: 7.5mm
User Control:
3 LEDs indicating Power, Video lock and Network lock
3 buttons for pairing, reset, boot;
FCC ID
IC
VQSAMN41012
7680A- AMN41012
Amimon Ltd. 26 Zarhin St. Raanana, Israel. Tel: +972-9-9629222 www.amimon.com
2017 © All rights reserved to Amimon ltd. Proprietary and Confidential
Confidentiality is requested
Table 2: AMN42012 - Technical Specifications
AMN42012
Frequency
Control:
Non-DFS Frequencies :
5.150~ 5.250 GHz for EU
5.150 ~ 5.250 GHz and 5.725~5.825 GHz for US
DFS Frequencies (used only in Aerial mode):
5.250-5.350 GHz and 5.470 ~ 5.725 GHz for EU
5.250-5.330 GHz and 5.470 ~ 5.725 GHz for US
5.250-5.350 GHz and 5.470 ~ 5.6GHz and 5.650 ~ 5.710 GHz for Canada
SRD Frequencies (EU):
5.725 ~ 5.875 GHz for EU
Antenna:
Total connectors: 5
1 transmitting chain with antenna diversity and 5 receive ports External using
on-board UFL Connectors: 2dBi omni Antenna gain or 12dBi directional
Antenna gain
Environment:
Operational: -20 ÷ 50°C , 10 ÷ 90% humidity
Storage: -20 ÷ 55° C, 10 ÷ 90% humidity
Voltage:
5VDC ±10%
Size:
L: 70.0mm x W: 55.0mm x H: 7.5mm
User Control:
3 LEDs indicating Power, Video lock and Network lock
3 buttons for pairing, reset, boot;
FCC ID
IC
VQSAMN42012
7680A- AMN42012
Amimon Ltd. 26 Zarhin St. Raanana, Israel. Tel: +972-9-9629222 www.amimon.com
2017 © All rights reserved to Amimon ltd. Proprietary and Confidential
Confidentiality is requested
Product Description
(1) AMN41012
Figure 1 –AMN41012 top view
Board-to-
board
connector
2dBi or 5dBi Antenna
Debug
Connector
Pairing button
Video LED
Power LED
Network LED
Reset button
Boot button
Amimon Ltd. 26 Zarhin St. Raanana, Israel. Tel: +972-9-9629222 www.amimon.com
2017 © All rights reserved to Amimon ltd. Proprietary and Confidential
Confidentiality is requested
(2) AMN42012
Figure 2 –AMN42012 top view
2dBi Omni Antenna
2dBi or 12dBi
Antenna
Reset
button
Pairing button
Boot button
Video LED
Power
LED
Network
LED
Debug
Connector
Board-to-
board
connector
Amimon Ltd. 26 Zarhin St. Raanana, Israel. Tel: +972-9-9629222 www.amimon.com
2017 © All rights reserved to Amimon ltd. Proprietary and Confidential
Confidentiality is requested
(3) LED behaviors
Network LED
Flashing Rate
Indication
Fast blinking (errors)
Stuck in bootloader / MAC not alive / No XML / default calibration
Off
Not registered to TX / power down / disconnected/ Waiting for user
response at registration
Normal blinking
Searching for TX
Fast blinking
During registration / out of range
On
In link
Table 3 - Network LED
Video LED
Flashing Rate
Indication
Fast blinking (errors)
Stuck in bootloader / MAC not alive / No XML / default calibration
Off
Not registered to TX / power down / disconnected/ Waiting for user
response at registration
Normal blinking
Searching for TX
Fast blinking
During registration / out of range
On
In link
Table 4 - Video LED
Power LED
Flashing Rate
Indication
Off
No power, power level is below acceptable levels
On
Power is supplied and ON/OFF switch is on (when exist).
Table 5 - Power LED
Amimon Ltd. 26 Zarhin St. Raanana, Israel. Tel: +972-9-9629222 www.amimon.com
2017 © All rights reserved to Amimon ltd. Proprietary and Confidential
Confidentiality is requested
(4) Board-to-Board Connector
The Interface connector provides various interfaces to communicate between the module
and the MCU to configure video related parameters and settings, or receive the network
status and communication related parameters.
The following interface options are available:
-External Power Supply voltage (5VDC ±10%)
-Signal Ground
-Video signal
-I2S audio interface
-I2C bus
-Indication output (Power, Network, Video Indications)
-Board attached ID pins
-UART
-USB
-SPI
Contact Amimon to request the complete pin allocation and functional description of the
interface board.
Amimon Ltd. 26 Zarhin St. Raanana, Israel. Tel: +972-9-9629222 www.amimon.com
2017 © All rights reserved to Amimon ltd. Proprietary and Confidential
Confidentiality is requested
Installation
The modules are designed to be integrated with any compatible Video Interface
Board (VIB), to provide a complete wireless Video Solution.
At common application, the VIB shall provide standard video interface that can be
connected to standard video monitor. This video interface may be HDMI, HD-SDI or
any other standard or custom video interface.
It is advised to verify compatibility of the VIB to the interface connector type, pin
functionality, and signal compatibility of the modules, before initiating the
installation.
At installation, make sure that the modules are firmly attached and secured to the
VIB by proper mechanical means.
Installation of the modules must provide the adequate heat dissipation means to
provide the modules ambient temperature within the product operating conditions as
specified.
Amimon Ltd. 26 Zarhin St. Raanana, Israel. Tel: +972-9-9629222 www.amimon.com
2017 © All rights reserved to Amimon ltd. Proprietary and Confidential
Confidentiality is requested
See ‘Product Description’for port location described in this section.
1. Connect AMIMON modules to the compatible Video Interface Board (VIB).
2. Connect the antennas to the modules. Only use antennas provided by
AMIMON
3. Connect the receiver VIB to a video monitor through the supported video
interface of the VIB.
4. Connect the transmitter VIB to a video source (for example, camera) through
the supported video interface of the VIB.
5. Power ON the VIB according to its operating
manual.
6. Set the Antenna orientation of the receiver module
to perform optimal performance:
One option is to separate the antennas to match the
picture. Receiving antennas should be oriented in the same plane as the
transmitting antenna.
7. If the devices are not paired to each other, press the "pairing" button on each
module.
Note: For maximal range
Keep line of sight between the transmitter and the receiver.
Avoid placing any obstacles besides the transmitter or the receiver.
Position both transmitter and receiver in an upwards position, for enhanced
antennas performance.
Mount the modules with proper air ventilation.
Use only approved accessories recommended by Amimon
Avoid Co-location: Place the modules and their antennas as far away as
possible from other transceiver devices, 20cm separation is a minimal
distance unless otherwise specified in the Grant.
Avoid Proximity to Metal Objects: The antennas must be at least 7 cm away
from any metal object.
This manual suits for next models
1
Table of contents
Other AMIMON Receiver manuals
