Amit RRE-F/001 User manual

rre-f001_g_en_103
RRE-F/001
Remote I/O unit
with Ethernet interface
Operation manual
Version 1.03

RRE-F/001
rre-f001_g_en_103 2/29
AMiT, spol. s r.o. does not provide any warranty concerning the contents of this
publication and reserves the right to change the documentation without any
obligation to inform about it.
This document can be copied and redistributed under following conditions:
1. The whole text (all pages) must be copied without any changes.
2. All redistributed copies must retain the AMiT, spol. s r.o. copyright notice
and any other notices contained in the documentation.
3. This document must not be distributed for purpose making of profit.
The names of products and companies used herein can be trademarks or
registered trademarks of their respective owners.
AMiT is a registered trademark.
Copyright (c) 2017, AMiT, spol. s r. o.
Producer: AMiT, spol. s r. o.
Naskové 3/1100, 150 00 Praha
www.amit.cz
Technical support: [email protected]

RRE-F/001
3/29 rre-f001_g_en_103
Contents History of revisions.........................................................................................4
Related documentation...................................................................................4
1. Introduction..........................................................................................5
2. Technical parameters..........................................................................6
2.1. Dimensions.....................................................................................................8
2.2. Recommended drawing symbol .....................................................................9
3. Labelling .............................................................................................10
3.1. Type label.....................................................................................................11
4. Conformity assessment....................................................................12
4.1. Other tests....................................................................................................13
5. Power supply......................................................................................14
6. Elements of the front panel...............................................................15
7. Inputs/outputs....................................................................................16
7.1. Digital inputs.................................................................................................16
7.2. Digital outputs...............................................................................................17
7.3. Power supplying of digital outputs................................................................17
7.4. Input / output state indication........................................................................18
8. Ethernet ..............................................................................................19
9. System LEDs......................................................................................20
10. Configuration .....................................................................................21
11. Mounting.............................................................................................22
11.1. Mounting instructions....................................................................................22
11.2. Mounting holes.............................................................................................22
11.3. Installation rules ...........................................................................................23
12. Factory settings.................................................................................24
13. Ordering information and completion .............................................25
13.1. Completion...................................................................................................25
14. Maintenance .......................................................................................26
15. Waste disposal...................................................................................29

RRE-F/001
rre-f001_g_en_103 4/29
History of revisions
Document name: rre-f001_g_en_103.pdf
Revision
Date
Author
Changes
100
11. 3. 2014
Šach Jaroslav
New document
101
16. 2. 2016
Šach Jaroslav
Digital Inputs schematic change, plastics weight correction,
adding chapters Labelling, Packaging
102
27.10.2016
Šach Jaroslav
Peak current correction
103
25.4.2017
Šach Jaroslav
DI voltage values correction. DI schematic correction. Minimal
voltage on VDDIO is 24 V DC
Related documentation
1. Application Note AP0037 –Principles of using Ethernet network
file: ap0037_en_xx.pdf
2. Application Note AP0051 –Ethernet network cabling on rolling stock
file: ap0051_en_xx.pdf

RRE-F/001
5/29 rre-f001_g_en_103
1. Introduction
RRE-F/001 is a remote I/O unit with Ethernet interface.
▪8 × digital input / output
▪1 × Ethernet, connector M12
▪PoE power supply according to IEEE 802.3af
▪Mounting on base plate
▪Design according to EN 50155:2007
Basic features

RRE-F/001
rre-f001_g_en_103 6/29
2. Technical parameters
Processor
STM32F207VET6
Internal FLASH memory
512 KB
RAM
128 KB
EEPROM
2 KB
Number of inputs / outputs
8 ×
Configuration
1 × 8
Input / output state indication
8 × LED
Common pole
GND
Type of inputs / outputs
24 V DC
Reverse polarity protection
Yes
Logical 0 of input
Min. -0.6 V, Max. 7 V
Logical 1 of input
Min. 13 V, Max. 34 V
Max level of input signal
34 V DC
Outputs design
MOS
Short circuit protection of
outputs
Yes
Maximum switched current
8 × 1 A
Connection point
WAGO 769-671/003-000
Wire cross section
0.75 mm2to 2.5 mm2
Internal power supply
24 V DC
Maximum power consumption
from internal power supply
80 mA
External power supply
24 V to 34 V DC
Number of lines
1 ×
Data transmission rate
10 / 100 Mbps
Galvanic separation
Yes *)
Galvanic separation strength
1000 V AC /1 minute *)
Connection point
M12 type connector according to IEC 61375-3-4 1
Recommended cabling
STP CAT5
Maximum segment length
100 m
*) Insulation must not be used for dangerous voltage separation.
PoE
48 V DC ±10 %
Device class according to IEEE
802.3af
Class 0
Maximum power consumption
9,6 W
Peak inrush current
20 A / < 5 ms
Galvanic separation
Yes *)
Galvanic separation strength
1000 V AC /1 minute *)
Connection point
M12 type connector according to IEC 61375-3-4
*) Insulation must not be used for dangerous voltage separation.
CPU
Digital inputs/
outputs
Supplying of
outputs
Ethernet
Power supply

RRE-F/001
7/29 rre-f001_g_en_103
Mechanical design
Formed metal 1.5 mm
Color type –cover
Powder color
Colour –cover
Light grey / RAL 7035
Mounting
On panel, 2 × M5 bolt with cylindrical head
Ingress protection rate
IP30
Weight –netto
–brutto
0.76 kg ±5 %
0.89 kg ±5 %
Dimensions (w × h × d)
(35 × 234 × 80) mm
Unit overall mass of plastics
89 g
Included mass of self-
extinguishing plastics¶
89 g
Device does not contain
PUR, PVC, Asbestos
Device conforms
2011/65/EU (ROHS)
1907/2006EU (REACH)
Operating temperature range
-40 °C to 70 °C
Storage temperature range
-40 °C to 70 °C
Maximum ambient humidity
< 95 % non-condensing
Expected MTBF
> 500 000 h
Expected lifetime
15 years
Device is supplied with loader, which enables software downloading via Ethernet line.
NO
Equipment is intended to operate up to 1 400 m above the sea level.
Equipment is designed to meet the Temperature Class T1.
According to EN 61373:2010 standard, the equipment is classified in terms of
vibrations into Category 1, Class A (mounting to vehicle body).
Permissible supplying voltage drop-outs duration: max. 10 ms (Class S2 according to
Chapter 3.1.1.2 of EN 50155:2007).
For supply voltage switching are permissible conditions of C1 and C2 Class.
The device is not classified according to EN 50128:2011 Railway applications –
Communications, signalling and processing systems –Software for railway control
and protection systems.
The device is not classified according to EN 50129:2003 Railway applications –
Communication, signalling and processing systems –Safety-related electronic
systems for signalling.
Mechanics
Dangerous
materials
Temperatures
Others
Software
Components
with reduced
lifetime
Claims EN
50155:2007
Safety
classification

RRE-F/001
rre-f001_g_en_103 8/29
2.1. Dimensions
80
150
119
233,5
192 210
35
o 6
Fig. 1 - RRE-F/001 dimensions in mm

RRE-F/001
9/29 rre-f001_g_en_103
2.2. Recommended drawing symbol
Following drawing symbol is recommended for RRE-F/001 unit. Only part of it
can be visible in following examples.
X2
RRE-F/001
X1
ETH
IO02
IO01
IO08
IO05
IO04
IO03
GNDIO
IO07
IO06
3
2
1
7
6
5
4
9
8
10
11
VDDIO
PE
Fig. 2 - Recommended drawing symbol for RRE-F/001

RRE-F/001
rre-f001_g_en_103 10/29
3. Labelling
There is a type label on the top side of the RRE-F/001. Image below shows the
label position.
TYPE
S/N
MAC
FW
PoE
WEIGHT
TEST
HiPot
DATE
xxxxxxxx
xx-xx-xx-xx-xx-xx
APP x.xx / LDR x.xx
802.3af, Class 0
0.76 kg
OK-MU
HiPot-OK
02.02.2016
RRE-F/001
Fig. 3 - RRE-F/001 type label position