AMX AC-CV6T User manual

Quick Start Guide
AC-CV6T Accessory Tabletop Enclosure Kit
ATTENTION: READ THIS FIRST!
For more detailed installation, configuration, and operating instructions,
refer to the 6" Color Video Touch Panels Instruction Manual available on-
line at www.amx.com.
Overview
The CV6T is designed to be used on any flat/level surface. The AC-CV6T
(FIG. 2) is a metallic tabletop enclosure that encases the CV6 touch panel
and allows its use on a wide variety of horizontal surfaces.
CAUTION:
Finishing Instructions for Aluminum AC-CV6T (FG5924-22).
Surface preparation for the Aluminum CV6T is very important.
The unfinished aluminum version of the AC-CV6T is supplied with
a sanded, non-coated aluminum bezel, aluminum panel mounting
blocks, and a stainless steel base enclosure. Please consult a
qualified painter for the appropriate surface treatment compatible
with the end users desired topcoat. Feet installation is done after
the painting process is completed.
Specifications
Setup of the AC-CV6T Tabletop Enclosure
The following sections describe the setup procedures for installing the AXD
touch panel into a tabletop enclosure. The enclosure works by encasing an
existing AXD-CV6 touch panel and using a tabletop cable (AXlink/Video) to
connect the unit to both a Master Controller and video sources.
Aluminum Feet Placement
The feet on and Alimunin Tabletop Enclosure sould be installed only after
the unit has been painted and allowed to dry properly. Refer to the FIG. 3
for the underside feet installation locations.
Installing the Wall Mount panel into a Tabletop Enclosure (AC-CV6T)
The CV6T enclosure is an optional metallic housing that is used to mount
the base CV6 LCD touch panel onto a horizontally flat surface. The
enclosure uses a plastic strain relief to secure the tabletop cable to the
enclosure.
To install Wall Mount touch panels into an AC-CV6T enclosure:
1. Remove the coiled 10-foot (3.05 m) tabletop cable and accessory bag
from within the enclosure.
2. Confirm that all of the included accessories are present in the box.
Refer to the Specifications AC-CV6T Enclosure table for content
information.
3. Uncoil the cable and thread the non-terminated end of the tabletop
cable into the enclosure and then out through the rear opening
(FIG. 4)
4. Continue to thread the cable through the strain relief opening until the
heat shrink tubing is located outside of the enclosure. Refer to FIG. 5
for the final position of the strain relief/cable combo.
FIG. 1 AC-CV6T Enclosure (CV6 unit inserted within)
FIG. 2 AC-CV6T Enclosure
AC-CV6T Specifications
Dimensions (HWD):
AC-CV6T
(FG5924-20/21/22)
• Faceplate: 6.47" x 8.69" x 0.60" (16.43 cm x 22.07 cm x 1.52 cm)
• Base Enclosure: 3.84" x 6.50" x 4.45" (9.75 cm x 16.51 cm x 11.30 cm)
Weight:
Enclosure with
AXD-CV6
Enclosure only
• 11.49 lbs. (5.21 kg)
• 3.75 lbs. (1.70 kg)
Enclosure • Metal enclosure and removable front panel bezel (matching colors):
Dark Grey matte finish (FG5924-20)
Platinum matte finish (FG5924-21)
Unfinished Aluminum (FG5924-22)Aluminum version of enclosure is
unpainted so as to provide easier preparation for custom painting
options.
Refer to the instruction manual for detailed Unfinished Aluminum
painting requirements and procedures.
Rear Connectors • All cable connectors are routed out from the enclosure via a hole
located on the rear of the unit
• Internal connections are made to the AXD-CV6 rear connectors via an
AC-CV6T tabletop cable.
Compatibility • AXD-CV6 White Video Touch Panel (FG5924-10)
• AXD-CV6 Black Video Touch Panel (FG5924-11)
Sample Dark Grey Sample Platinum
Mounting blocks (2)
Strain relief/cable
insertion location Base enclosure
AC-CV6T Specifications (Cont.)
Included Accessories • 2 Mounting blocks (attach the bezel to the base)
• 4 Mounting screws
• 10’ (3.05 meters) AC-CV6T Tabletop cable (Video/AXlink cable combo)
(64-5924). Uses BNC and mini-Phoenix AXlink connectors
• 1 BNC connector (for use in terminating the Red mini-coax cable)
(41-1077)
• 1 black strain relief (secures tabletop cable to enclosure) (45-0004-02)
FIG. 3 Aluminum feet installation locations (underside view)
FIG. 4 Threading the tabletop cable through the base enclosure
Measurement given
in inches

93-5924-01 REV: C
AMX Corporation reserves the right to alter specifications without notice at any time.
For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).
036-004-2678 6/03 ©2003
AMX Corporation. All rights reserved. The AMX logo is a trademark of AMX Corporation. AMX reserves the right to alter specifications without notice at any time.
3000RESEARCHDRIVE,RICHARDSON, TX75082• 800.222.0193 •fax469.624.7153 •technical support800.932.6993•www.amx.com
5. Position the strain relief onto the cable with the strain relief located
against the heat shrink tubing (at the base of the tabletop cable split)
as shown in FIG. 6. The strain relief should begin clasping after the
heat shrink.
WARNING!
VERIFY THE DIRECTION AND LOCATION OF THE STRAIN
RELIEF. The clip must be facing UP (on top). Once closed, it is
difficult to re-open. Grooves align against heat shrink and the flat
circular opening faces away from the enclosure.
6. Close the strain relief over the designated location.
Caution: Verify the relief is securely closed over the cable and facing
the correct direction.
The process of securing the strain relief might require the use of
pliers.
7. Firmly insert the cable/strain relief combo into the base enclosure
opening by pushing the combo through the base opening (toward the
inside) until the relief is securely flush against the base. Refer to
FIG. 5 for the final position of the strain relief/cable combo.
8. Position the base enclosure onto a flat surface.
9. Grip the CV6 unit, from either sides of the enclosure, and while
angling the front of the CV6 unit upwards, connect the AXlink and
BNC connectors (FIG. 7) at the their respective connector locations
shown below.
10. Carefully slide-in the connected CV6 unit (Cin FIG. 8) into the base
enclosure until the CV6 flanges lie flat against the base enclosure.
Take care in positioning the connector wires into the open space
within the base (under the CV6 unit).
11. Position the faceplate/bezel (Din FIG. 8) above the enclosure base.
12. Securely grab the LCD and enclosure unit combo (enclosure unit is
made up of the base and faceplate).
13. Carefully flip the combo over onto a soft cloth to prevent scratching
the faceplate during the installation of the mounting blocks.
14. Insert the mounting blocks (Bin FIG. 8) into the opening below both
sides of the faceplate. The elevated groove on the blocks should lie
against the base enclosure.
15. Insert two of the provided enclosure screws into each of the
mounting brackets and secure the bracket to the faceplate by turning
the screws using a clockwise motion. Repeat this step for the second
mounting bracket.
Note: If using the enclosed BNC connector (41-1077) to terminate the
cable, use of a hexagonal crimp tool (with a 0.178 opening) for
installation onto the red mini-coax cable (see FIG. 6).
FIG. 5 Installation of relief/cable combo into the AC-CV6T enclosure
FIG. 6 Tabletop cable and strain relief installation
Rear view Circular front of
Strain relief
is mounted on the
edge of the heat shrink
strain relief lies
flush against the
enclosure
Heat
shrink
CLIP FACING UP
First - Thread through
Second - Snap closed
RELIEF GROOVES GO INTO ENCLOSURE
FLAT SURFACE POINTS AWAY
10 inches
FROM ENCLOSURE
total
and position
FIG. 7 Rear views of the CV6 touch panel
FIG. 8 Installation of main CV6 unit into an AC-CV6T enclosure
BNC (female)
DB-9 RS-232
CV6 (Rear view)
2-pin PWR
4-pin AXlink
connector
connector
video
connector
connector
A
B- 2 mounting blocks
C- Main AXD-CV6
- Base
opening
secure the base to the faceplate
touch panel unit
D- AC-CV6T
faceplate/bezel
CV6
Screws (8-32)
(showing
strain relief
installed)
flanges
Base enclosure
Other AMX Rack & Stand manuals

AMX
AMX MAX-HT User manual

AMX
AMX CB-TP17 User manual

AMX
AMX Modero S Series User manual

AMX
AMX NXA-SMT43X User manual

AMX
AMX MB-TP12 User manual

AMX
AMX NXA-TTS500-BL User manual

AMX
AMX NXA-TTS43X-BL User manual

AMX
AMX MB-TP17 User manual

AMX
AMX Modero ViewPoint MVP-7500 User manual

AMX
AMX CB-MSA-10 User manual