AMX Modero S Series User manual

Quick Start Guide
MSA-AMK-07/10 Modero S Series®Any Mount Kit
MSA-AMK-07/10
The MSA-AMK-07 and MSA-AMK-10 Any Mount Kits are designed to mount
7"or 10” Modero S Series Wall Mount Touch Panels into standard single or
double gang boxes in the US, UK, EU and Australia, making the installation of a
Modero S Series control interface simple and effective. The MSA-AMK-07
(FG2265-25) is compatible with the MSD-701 (FG2265-02), while the
MSA-AMK-10(FG2265-26)(FIG. 1)iscompatiblewithMSD-1001(FG2265-01).
Installation of the Any Mount Kit
The Any Mount Kits are designed to utilize existing or newly installed gang
boxes, with a new back box to replace the back box included with the touch
panel. To install an Any Mount Kit and its accompanying touch panel:
1. Before starting the installation, ensure that Ethernet cable has been pulled
to the gang box, and that all appropriate Power Over Ethernet (PoE)
injectors have been connected to the cable going to the gang box.
2. If the gang box already has an existing fixture or device installed in it,
remove the fixture or device to expose the gang box (FIG. 2).
3. Pull the Ethernet cable into the gang box, making sure that the male RJ-45
connector is accessible within the gang box.
4. Match the screw connector holes on the gang box with the holes in the
back box (FIG. 3). The Any Mount Kit back box has multiple holes to allow
for single or double gang box design, and for standard gang box designs
from the US, UK, EU and Australia. At the same time, examine how the
back box rests on the gang box, looking for gaps between the back box
and the wall surface.
5. If the gap between the wall and the back box is extreme, or if the
installation of the back box exposes too much of the gang box, you may
apply the optional foam gasket (MSA-AMK-07: 66-2265-29; MSA-AMK-10:
66-2265-30) to the back of the back box. Peel the adhesive backing off the
gasket and carefully apply it to the back box surface (FIG. 4).
6. Once you have confirmed the proper mounting position of the back box,
attach the back box to the gang box, using either the screws used with the
original fixture or device or with the included screws in the Any Mount Kit
(FIG. 5).
WARNING: Be careful not to over-tighten the screws, which can bow or
damage the back box.
FIG. 1 MSA-AMK-10 Any Mount Kit back box (rear)
Product Specifications
Models Available: • MSA-AMK-07 (FG2265-25)
• MSA-AMK-10 (FG2265-26)
Dimensions (HWD): • MSA-AMK-07: 4.88” x 7.38” x 0.91”
(12.39 cm x 18.75 cm x 2.25 cm)
•MSA-AMK-10: 3.42” x 5.04” x 1.04”
(8.68 cm x 12.81 cm x 2.64 cm)
Weight: • MSA-AMK-07: 0.10 lbs (45.36 g)
•MSA-AMK-10: 0.25 lbs (113.40 g)
Certifications: TBD
Included Accessories: MSA-AMK-07:
• Back Box (60-2265-33)
• Gasket, Foam (66-2265-29)
• Screw, M3.5 X 30mm, PFH, Clear Zinc (4) (80-1620-04)
• Screw, #6-32 X 1.25, PFH, Type F, Clear Zinc (4)
(80-1700-09)
MSA-AMK-10:
• Back Box (60-2265-34)
• Gasket, Foam (66-2265-30)
• Screw, M3.5 X 30mm, PFH, Clear Zinc (4) (80-1620-04)
• Screw, #6-32 X 1.25, PFH, Type F, Clear Zinc (4)
(80-1700-09)
Other AMX
Equipment: • MSD-701 7” Modero S Series Wall Mount Touch Panel (FG2265-02)
• MSD-1001 10” Modero S Series Wall Mount Touch Panel
(FG2265-26)
FIG. 2 Existing gang box
Gang Box
Wall surface
FIG. 3 Testing the alignment of the back box screw holes.
FIG. 4 Applying the optional foam gasket to the back box.
FIG. 5 Installing the back box to the gang box.
Gasket
Adhesive backing

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).
2/14
©2014 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.
AMX reserves the right to alter specifications without notice at any time.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax [phone] • technical support 800.932.6993 • www.amx.com
93-2265-25 REV: A
7. After installing the back box, inspect the back box’s placement. If
necessary, the back box can be removed and the foam gasket installed.
8. Pull enough slack on the Ethernet cable through the back box to allow the
cable to reach the touch panel’s RJ45 connector (FIG. 6).
9. Remove the touch panel’s back box to access the back of the panel.
10. Insert each connector into its corresponding location along the back of the
touch panel. For more information on connection, please refer to the
Operation Reference Guide for the Modero S Series panel being installed,
available from www.amx.com.
11. Test the incoming wiring by attaching the panel connections to their
terminal locations and applying power. Verify that the panel is receiving
power and functioning properly to prevent repetition of the installation.
12. Latch the panel onto the top hooks on the back box and rotate it down
(FIG. 7).
13. Press gently but firmly and evenly on the surface of the touch panel until
the top panel snap “clicks” to lock it down (FIG. 8).
WARNING: if you see a gap between the panel and the back box, or feel any
binding while locking down the panel, stop immediately and verify that no cables
or other items are in the way. Do not force the panel into position, as this can
cause damage to the touch screen or the panel electronics.
Uninstalling the Touch Panel
In order to access the back of the touch panel, such as to install a USB
connection for firmware upgrades, the device may need to be uninstalled from
the back box. To uninstall the touch panel:
1. From the bottom, pull gently outward from the back box. Gently rock the
panel back and forth to free the bottom from the back box.
2. Rotate it up to release the top latch hooks, and carefully pull the device
free from the back box. Take care not to damage or pull the connections on
the back of the device, or to pull the back box from the gang box.
FIG. 6 Accessing the Ethernet cable through the back box.
FIG. 7 Hooking the top of the touch panel on the back box.
Pull Ethernet cable
through back box
Top hooks
FIG. 8 Locking down the bottom of the touch panel onto the back box.