AN SON GHDSV-1404 User manual

SCREWDRIVER HAMMER
SELF-PREPARED TOOLS: Tools below are NOT included in package.
Read instruction carefully . See Furniture Parts list and Hardware List for guidance . Be sure you have all parts before you start assembling .
Place and assemble furniture on a clean flat soft surface , such as carpet or rug to pervent being scratched .
Before you begin, please follow assembly instructions carefully, then follow them step by step.
Reminder:
Please ensure that all surfaces and edges with colours/laminations are facing forward/outward.
1
2
PART LIST
TOP TRAY 1 PC MINI FIX
4
SIDE PANEL (L)
6
SIDE PANEL (R)
7
8
QTY
1 PC
1 PC
31 PC
5
2 PCS
6 PCS
HARDWARE
A
B
C
D
E
F
G
8 PCS
M3.5 X 16MM C.B SCREW 44 PCS
ALLEN KEY M4 1 PC
BOTTOM PANEL
DRAWER FRONT (DOWN)
DRAWER SIDE
H
I
J
K
M6 X 5OMM
CSK CAP WOOD SCREW 4 PCS
A1 A2 A3
M8 X 30MM WOOD DOWEL 20 PCS
9
10
11
4 PCS
LEG
5/8 NAIL 56 PCS
M4 X 38MM C.B SCREW 24 PCS
MODEL : ASSEMBLY INSTRUCTIONS PAGE: /6
1
12
13
14
1 PC
DRAWER FRONT (UP)
BACK PANEL 1 PC
MIDDLE PANEL 1 PC
ONE HOLE L BRACKET (2MM) 4 PCS
JCBC Screw M6 x 70
SPRING WASHER M6
FLAT WASHER M6
8 PCS
8 PCS
8 PCS
L
M
METAL SHELF SUPPORT 8 PCS
3 PCS
DRAWER BOTTOM
3 PCS
DRAWER BACK
SHELF PANEL 2 PCS
2 PCS
BONE PANEL
10'' DRAWER SLIDE J1 ( L/R )
J2 ( L/R ) 3 SETS
1
2
3
4
5
6
7
7
8
910 10
12
12
12
11 11 11
11
13
13
13
14
N
TIPPING PACK
2 SETS
N1
N2
N3
N4 N5
POWER DRILL
GHDSV-1404

STEP 1 STEP 2
STEP 3 STEP 4
MODEL : ASSEMBLY INSTRUCTIONS PAGE: /6
2
SCREWDRIVER
REQUIRED
- Insert hardware A1 onto panel (5).
(Repeat 4 times.)
- Insert hardware A2 onto panel (1).
(Repeat 4 times.)
- Insert hardware B onto panel (5).
(Repeat 4 times.)
* Ensure the arrows on hardware A1 point towards mounting positions.
A2
x4
ROTATE
1
5
PRESS
A1
x2
x2
A1
PRESS
x4
PRESS
B
SCREWDRIVER
REQUIRED
- Insert hardware A1 onto panel (3) and (4).
(Repeat 4 times.)
- Insert hardware A2 onto panel (3) and (4).
(Repeat 4 times.)
- Insert hardware B onto panel (3) and (4).
(Repeat 8 times.)
* Ensure the arrows on hardware A1 point towards mounting positions.
PRESS
A1
x4
A2
x4
ROTATE
x8
PRESS
B
4
3
- Assemble hardware F to panel (6) with hardware G.
(Repeat 2 times on each panel.)
- Insert hardware B onto panel (6).
(Repeat 4 times on each panel.)
SCREWDRIVER
REQUIRED
x8
PRESS
B
x4
ROTATE
F
G
6
Fix hardware J1 (L/R) into panel (3) and (4) with hardware G.
(Repeat 3 times for each hardware.)
SCREWDRIVER
REQUIRED
J1(L)
J1(R)
x6
ROTATE
x6 x6
ROTATE ROTATE
GGG
Second hole from the edge.
First hole from the edge. Small hole at the center.
3
4
J1(L)
GHDSV-1404

STEP 5 STEP 6
STEP 7 STEP 8
MODEL : ASSEMBLY INSTRUCTIONS PAGE: /6
3
- Assemble hardware F on panel (6) to panel (3) and (4)
by using hardware G.
(Repeat 1 times on each side panel.)
SCREWDRIVER
REQUIRED
x4
ROTATE
F
G
3
4
5
1
2
6
Connect panel (2) to panel (3) and (4) by using hardware C and E.
(Repeat 4 times.)
* In this step hardware B are pre-inserted.
ROTATE
x4
C
E2
4
3
1
5
- Attach panel (3) and (4) to panel (1).
- Insert all hardware A2 into A1.
- Rotate all A1 until tight.
- Apply A3 onto all A1.
(Repeat 4 times.)
OR
SCREWDRIVER
REQUIRED
* In this step hardware A1, A2 and B are pre-inserted.
HARDWARE
E
ROTATE
Section View
x4
A2
A1
x4 PRESS
A3
4
3
1
5
- Attach panel (5) to panel (3) and (4).
- Insert all hardware A2 into A1.
- Rotate all A1 until tight.
- Apply A3 onto all A1.
(Repeat 4 times.)
- Attach panel (6) to
panel (3) and (4).
(Repeat 2 times.)
OR
SCREWDRIVER
REQUIRED
* In this step hardware A1, A2 and B are pre-inserted.
HARDWARE
E
ROTATE
Section View
x4
A2 A1
x4
PRESS
A3
5
4
3
6
GHDSV-1404

STEP 9 STEP 10
STEP 11 STEP 12
MODEL : ASSEMBLY INSTRUCTIONS PAGE: /6
4
Assemble the panel (7) into between panel (3) and (4).
(Repeat 2 times.)
* In this step hardware I are pre-inserted.
7
7
5
4
3
1
2
Insert hardware I into mounting positions on panel (3) and (4) by hand.
(Repeat 8 times.)
x8 PRESS
I
1
5
4
3
2
HAMMER
REQUIRED
Assemble panel (8) to entire body with hardware D.
(Repeat 32 times.)
x32
HIT
D
8
3
2
Assemble part 14 into panel (2) by using hardware E, K, L and M.
(Repeat 2 times for each Leg.)
ROTATE
x8
E
K
L
M
14
3
4
1
5
2
14
GHDSV-1404

STEP 13 STEP 14
STEP 15 STEP 16
MODEL : ASSEMBLY INSTRUCTIONS PAGE: /6
5
Assemble hardware J2 (L/R) to panel (13) by using hardware G.
(Repeat 3 times for each hardware.)
Hole at the center.
Third hole from the edge. Third hole from the edge.
x6
G
x6
G
x6
G
ROTATE ROTATE ROTATE
*Hardware J2 (L/R) shall be leaning against panel (9) or (10) when assembling.
SCREWDRIVER
REQUIRED
13
13 13
12
12 12
11
11 11
10
10
9
J2 (L)
J2 (R)
J2 (L)
J2 (R)
J2 (R)
J2 (L)
Assemble panel (13) to entire body with hardware D.
(Repeat 8 times for each drawer.)
HAMMER
REQUIRED
x24
HIT
D
13
13
13
12
12
12
11
11 11
10
10
9
Put all the drawer in place along the drawer slides.
4
3
1
7
7
5
9
10
10
Assemble panel (11) with panel (9) or (10) and (12)
by using hardware H.
(Repeat 8 times for each drawer.)
SCREWDRIVER
REQUIRED
ROTATE
H
x24
11
11
10
12
11
11
10
12
11
11
12
9
GHDSV-1404

MODEL : ASSEMBLY INSTRUCTIONS PAGE: /6
STEP 17 STEP 18
STEP 19 STEP 20
6
Assemble hardware N1 into panel (1) and (8)
by using hardware N2.
(Repeat 2 times.)
SCREWDRIVER
REQUIRED
ROTATE
- Mark and use the power drill
to drill a hole on the wall.
- Hit hardware N3 into the wall.
(Repeat 2 times.)
HAMMER
REQUIRED
POWER
DRILL
REQUIRED
- Assemble hardware N1 to N3 by using hardware N4.
(Repeat 2 times.)
- Connect two of the hardware N1 by using hardware N5.
- Tighten the hardware N5.
(Repeat 2 times.)
HIT
ROTATE
TIGHTEN
CONNECT
SCREWDRIVER
REQUIRED
x2
N1
N2 x2
N3
x2
N1
N3
N4 x2
N1
N1
N5
x2
N1
N1
N5
1
4
8
4
1
11
4
4
7
7
7
7
7
7
55
5
9
9
9
10
10
10
10
10
10
GHDSV-1404