Analog Devices ADSP-21160 EZ-KIT Lite User manual

ADSP-21160 EZ-KIT LITE
Evaluation System Manual
First Edition, May 2002
Part Number
82-000603-01
Analog Devices, Inc.
Digital Signal Processing Division
One Technology Way
Norwood, MA 02062-9106 a

Limited Warranty
The EZ-KIT Lite evaluation system is warranted against defects in materials and
workmanship for a period of one year from the date of purchase from Analog
Devices or from an authorized dealer.
Disclaimer
Analog Devices, Inc. reserves the right to change this product without prior
notice. Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its use;
nor for any infringement of patents or other rights of third parties, which may
result from its use. No license is granted by implication or otherwise under the
patent rights of Analog Devices, Inc.
Trademark and Service Mark Notice
EZ-KIT Lite, VisualDSP++, VisualDSP++ logo, CROSSCORE, CROSSCORE
logo, Blackfin and the Blackfin logo are trademarks of Analog Devices Inc.
SoundMAX, EZ-ICE, SHARC, the SHARC logo, TigerSHARC, and the
TigerSHARC logo, are registered trademarks of Analog Devices, Inc. All
trademarks and logos are property of their respective holders.
Microsoft and Windows are registered trademarks of Microsoft Corporation.
Adobe and Acrobat are trademarks of Adobe Systems Incorporated.
All other brand and product names are trademarks or service marks of their
respective owners.
The EZ-KIT Lite evaluation system contains ESD (electrostatic
discharge) sensitive devices. Electrostatic charges readily
accumulate on the human body and equipment and can
discharge without detection. Permanent damage may occur on
devices subjected to high-energy discharges. Proper ESD
precautions are recommended to avoid performance degradation
or loss of functionality. Store unused EZ-KIT Lite boards in the
protective shipping package.
ADSP-21160 EZ-KIT Lite Evaluation System Manual ii

TABLE OF CONTENTS
LIST OF TABLES.............................................................................................................. v
LIST OF FIGURES ............................................................................................................ v
1INTRODUCTION.................................................................................................. 1-1
1.1 For More Information About Analog Devices Products................................. 1-3
1.2 For Technical or Customer Support................................................................ 1-3
1.3 Purpose of This Manual ..................................................................................1-3
1.4 Intended Audience........................................................................................... 1-4
1.5 Manual Contents ............................................................................................. 1-4
1.6 Online Help ..................................................................................................... 1-5
2GETTING STARTED............................................................................................ 2-6
2.1 Overview ......................................................................................................... 2-6
2.2 Contents of Your EZ-KIT Lite Package ......................................................... 2-6
2.3 PC Configuration............................................................................................. 2-7
2.4 Installation Tasks............................................................................................. 2-7
2.4.1 Installing the VisualDSP++ Software ......................................................2-7
2.4.2 Installing the VisualDSP++ License ........................................................ 2-8
2.4.3 Installing the EZ-KIT Lite Debug Software............................................. 2-8
2.4.4 Setting Up the EZ-KIT Lite Hardware..................................................... 2-8
2.4.5 Installing the EZ-KIT Lite USB Driver..................................................2-10
2.4.6 Verifying Driver Installation .................................................................. 2-22
2.4.7 Starting VisualDSP++ ............................................................................ 2-23
3USING THE EZ-KIT LITE EVALUATION SYSTEM...................................... 3-24
3.1 Overview ....................................................................................................... 3-24
3.2 EZ-KIT Lite License Restrictions ................................................................. 3-25
3.3 Memory Map................................................................................................. 3-25
3.4 Using the Flags and External IRQs............................................................... 3-26
3.5 Example Programs ........................................................................................ 3-27
3.6 Using the Flash Programmer Utility ............................................................. 3-27
4EZ-KIT LITE HARDWARE REFERENCE ....................................................... 4-28
4.1 Overview ....................................................................................................... 4-28
4.2 System Architecture ...................................................................................... 4-28
4.2.1 External Port ........................................................................................... 4-29
4.2.2 SPORT0 – Audio Interface..................................................................... 4-29
4.2.3 Expansion Interface ................................................................................ 4-30
4.2.4 JTAG Emulation Port ............................................................................. 4-30
4.3 Jumper and DIP Switch Settings................................................................... 4-31
4.3.1 Audio Input Select Jumper (JP1)............................................................ 4-31
4.3.2 Boot Mode Select Switch (SW1)............................................................ 4-32
4.4 LEDs and Push Buttons................................................................................. 4-33
4.4.1 Reset LEDs (LED1, LED7).................................................................... 4-33
4.4.2 Flag LEDs (LED2, LED3, LED4).......................................................... 4-34
4.4.3 USB Monitor LED (LED5) .................................................................... 4-34
4.4.4 Power LED (LED6)................................................................................ 4-34
4.4.5 IRQ Push Buttons (SW3, SW4, SW5) ................................................... 4-34
ADSP-21160 EZ-KIT Lite Evaluation System Manual iii

4.4.6 Reset Push Button (SW2)....................................................................... 4-35
4.5 Connectors..................................................................................................... 4-35
4.5.1 Expansion Interface (P1, P2, P3)............................................................ 4-36
4.5.2 Power Connector (P4) ............................................................................ 4-36
4.5.3 Link Ports (P5, P6) ................................................................................. 4-37
4.5.4 USB (P7)................................................................................................. 4-37
4.5.5 JTAG (P8)............................................................................................... 4-37
4.5.6 Audio (P9, P10) ...................................................................................... 4-37
4.5.7 SPORT0 (P11)........................................................................................ 4-38
4.6 Specifications ................................................................................................ 4-38
4.6.1 Power Supply.......................................................................................... 4-38
4.6.2 Mechanical Dimensions ......................................................................... 4-39
APPENDIX A: BILL OF MATERIALS............................................................................. I
A.1: ADDS-21160-EZLITE........................................................................................... I
A.2: ADDS-21160N-EZLITE...................................................................................... V
APPENDIX B: SCHEMATIC.......................................................................................... IX
INDEX ............................................................................................................................... X
ADSP-21160 EZ-KIT Lite Evaluation System Manual iv

LIST OF TABLES
Table 1-1: Related DSP Documents ................................................................................ 1-5
Table 1-2: Related VisualDSP++ Documents ................................................................. 1-5
Table 2-1: Minimum PC Configuration........................................................................... 2-7
Table 3-1: EZ-KIT Lite Evaluation System Memory Map ........................................... 3-26
Table 3-2: Flag Pin Summary........................................................................................ 3-27
Table 4-1: Connector Interfaces..................................................................................... 4-30
Table 4-2: Boot Mode Select Switch (SW1) Settings ................................................... 4-32
Table 4-3: Programmable Flag LEDs............................................................................ 4-34
Table 4-4: Programmable Flag Switches....................................................................... 4-34
Table 4-5: P1, P2, P3 Part Number Information............................................................ 4-36
Table 4-6: P4 Part Number Information ........................................................................ 4-36
Table 4-7: P5, P6 Part Number Information.................................................................. 4-37
Table 4-8: P7 Part Number Information ........................................................................ 4-37
Table 4-9: P9, P10 Part Number Information................................................................ 4-38
Table 4-10: P11 Part Number Information .................................................................... 4-38
Table 4-11: Power Connector ........................................................................................ 4-38
LIST OF FIGURES
Figure 2-1: EZ-KIT Lite Hardware Setup ....................................................................... 2-9
Figure 2-2: Add New Hardware Wizard........................................................................ 2-10
Figure 2-3: Search for the Driver................................................................................... 2-11
Figure 2-4: Search the CD-ROM................................................................................... 2-11
Figure 2-5: The Driver is Located ................................................................................. 2-12
Figure 2-6: Search for .sys File Dialog Box .................................................................. 2-12
Figure 2-7: Open the .sys File........................................................................................ 2-13
Figure 2-8: Copying Files Dialog Box........................................................................... 2-13
Figure 2-9: Finish the Software Installation .................................................................. 2-14
Figure 2-10: Found New Hardware Wizard .................................................................. 2-15
Figure 2-11: Search for a Suitable Driver...................................................................... 2-16
Figure 2-12: Locate Driver Files.................................................................................... 2-17
Figure 2-13: Driver File Search Results ........................................................................ 2-18
Figure 2-14: Completing Driver Installation Dialog Box.............................................. 2-19
Figure 2-15: Found New Hardware Wizard .................................................................. 2-20
Figure 2-16: Search for the Best Driver......................................................................... 2-21
Figure 2-17: Completing Driver Installation Dialog Box.............................................. 2-22
Figure 2-18: New Session Dialog Box ..........................................................................2-23
Figure 4-1: System Architecture.................................................................................... 4-28
Figure 4-2: Jumper and DIP Switch Locations.............................................................. 4-31
Figure 4-3: Audio Input Jumper Settings (JP1) ............................................................. 4-32
Figure 4-4: LED and Push Button Locations................................................................. 4-33
Figure 4-5: Connector Locations ................................................................................... 4-35
Figure 4-6: Mechanical Drawing ................................................................................... 4-39
ADSP-21160 EZ-KIT Lite Evaluation System Manual v

1 INTRODUCTION
Thank you for purchasing the ADSP-21160 EZ-KIT Liteevaluation system.
The evaluation board is designed to be used in conjunction with the
VisualDSP++development environment to test the capabilities of the
ADSP-21160 digital signal processor (DSP). The VisualDSP++ development
environment gives you the ability to perform advanced application code
development and debug such as:
• Creating, compiling, assembling, and linking application programs written
in C++, C and ADSP-2116x assembly
• Loading, running, stepping, halting, and setting breakpoints in application
programs
• Reading and writing data and program memory
• Reading and writing core and peripheral registers
• Plotting memory
Access to the ADSP-21160 from a PC is achieved through a USB port or an
optional JTAG emulator. The USB interface gives unrestricted access to the
ADSP-21160 DSP and the evaluation board peripherals. Analog Devices JTAG
emulators offer faster communication between the host PC and target hardware.
Analog Devices carries a wide range of in-circuit emulation products. To learn
more about Analog Devices emulators and DSP development tools, go to
http://www.analog.com/dsp/tools/.
The ADSP-21160 EZ-KIT Lite evaluation system provides example programs to
demonstrate the capabilities of the DSP and the evaluation board.
NOTE: The VisualDSP++ license provided with this EZ-KIT Lite evaluation
system limits the use of memory to 21K-words of program memory.
ADSP-21160 EZ-KIT Lite Evaluation System Manual 1-1

The board’s features include:
• Analog Devices ADSP-21160 DSP
o ADSP-21160M
o 2.5V Core Voltage
o 80 MHz Core Clock Speed
o ADSP-21160N
o 1.9V Core Voltage
o 95 MHz Core Clock Speed
o Boot Mode – switch configurable
• USB Debugging Interface
• Analog Devices AD1881A 48 kHz AC’97 SoundMAXCodec
o Jumper-Selectable Line-In or Mic-In 3.5-mm Stereo Jack
o Line-Out 3.5-mm Stereo Jack
• SBSRAM
o 512 KB (64K x 32-bits x 2-chips)
• Flash Memory
o 512 KB (512K x 8-bits)
• Interface Connectors
o 14-Pin Emulator Connector for JTAG Interface
o SPORT0 Connector
o 2 Link Port Connectors
o Expansion Interface Connectors (not populated)
• General-Purpose I/O
o 3 Push Buttons connected to DSP IRQs
o 3 LEDs connected to DSP Flags
The EZ-KIT Lite board has two types of external memory: flash and SBSRAM.
The flash can be used to store user-specified boot code. By configuring the boot
mode switch (SW1) and programming the flash, the board can run as a stand-
alone unit. For information about the external memory, see section 3.3.
SPORT0 is interfaced to an audio codec, allowing you to create audio signal
processing applications. SPORT0 is also attached to an off-board connector to
allow communication with other serial devices. For information about SPORT0,
see section 4.2.2.
Additionally, the EZ-KIT Lite board provides access to most of the DSP’s
peripheral ports on populated expansion interface connectors. For information
about the expansion interface, see section 4.2.3.
ADSP-21160 EZ-KIT Lite Evaluation System Manual 1-2

1.1 For More Information About Analog Devices Products
Analog Devices can be accessed on the Internet at http://www.analog.com. You
can directly access the DSP Web pages at http://www.analog.com/dsp. This page
provides access to DSP-specific technical information and documentation,
product overviews, and product announcements. For specific information about
DSP tools, go to http://www.analog.com/dsp/tools.
You may also obtain additional information about Analog Devices and its
products in any of the following ways:
• FAX questions or requests for information to [phone].
• Access the Computer Products Division File Transfer Protocol (FTP) site
at 137.71.23.21 or ftp://ftp.analog.com.
1.2 For Technical or Customer Support
You can reach our Customer Support group in the following ways:
• Contact your local Analog Devices sales office or an authorized Analog
Devices distributor.
• Call:
(800)-ANALOGD
• E-mail general DSP questions to:
[email protected]
[email protected] (European customer support)
• E-mail DSP Tools questions to:
[email protected]
• Submit a DSP Tools Technical Support Form:
http://forms.analog.com/Form_Pages/DSP/tools/contactDSP.asp
1.3 Purpose of This Manual
The ADSP-21160 EZ-KIT Lite Evaluation System Manual provides instructions
for installing the software on your PC and using the hardware. This manual
provides guidelines for running your own code on the ADSP-21160 EZ-KIT Lite
evaluation system. This manual also provides a description of the use and
configuration of the components on the evaluation board. A schematic and a bill
of materials are provided as reference for future ADSP-21160 board designs.
ADSP-21160 EZ-KIT Lite Evaluation System Manual 1-3

1.4 Intended Audience
This manual is a user’s guide and reference to the ADSP-21160 EZ-KIT Lite
evaluation system. DSP programmers who are familiar with the Analog Devices
SHARC DSP architecture, operation, and programming are the primary audience
for this manual.
DSP programmers who are unfamiliar with Analog Devices SHARC DSPs can
use this manual in conjunction with the ADSP-21160 SHARC DSP Hardware
Reference and the ADSP-21160 SHARC DSP Instruction Set Reference, which
describe the DSP architecture and instruction set. DSP programmers who are
unfamiliar with VisualDSP++ should refer to the VisualDSP++ Help menu and
the VisualDSP++ User’s Guide. For the locations of these documents, refer to
section 1.6.
1.5 Manual Contents
This manual contains the following information:
• Chapter 1 — Introduction
Provides manual information and Analog Devices contact
information.
• Chapter 2 — Getting Started
Provides software and hardware installation procedures and PC
system requirements.
• Chapter 3 — Using the EZ-KIT Lite
Provides information on the EZ-KIT Lite evaluation system from a
programmer’s perspective, and the EZ-KIT Lite specific memory
map.
• Chapter 4 — EZ-KIT Lite Hardware Reference
Provides information on the hardware aspects of the evaluation
system.
• Appendix A — Bill of Materials
Provides a list of components used to manufacture the EZ-KIT Lite
board.
• Appendix B — Schematics
Provides the resources to allow EZ-KIT Lite evaluation system
board-level debugging or to use as a reference design.
ADSP-21160 EZ-KIT Lite Evaluation System Manual 1-4

1.6 Online Help
Your software installation kit includes online Help as part of the Windows
interface. These Help files (.CHM) provide information about VisualDSP++ and
the ADSP-21160 EZ-KIT Lite evaluation system.
To view VisualDSP++ Help, click on the Help menu item or go to the Windows
task bar and select Start\Programs\VisualDSP\VisualDSP++ Help. To view help
on additional ADSP-21160 EZ-KIT Lite evaluation system features, go to the
windows task bar and select Start\Programs\VisualDSP\EZ-KIT Help. The
documents in the following tables can be found through online Help or in the
Docs folder of your VisualDSP++ installation.
For more documentation, please go to
http://www.analog.com/technology/dsp/library.html.
Table 1-1: Related DSP Documents
Document Name Description
ADSP-21160 DSP Datasheet General functional description, pinout,
and timing.
ADSP-21160 SHARC DSP
Hardware Reference
Internal DSP architecture and all
register functions.
ADSP-21160 DSP Instruction
Set Reference
All allowed DSP assembly instructions.
Table 1-2: Related VisualDSP++ Documents
Document Name Description
VisualDSP++ 2.0 Users
Guide for ADSP-21xxx DSPs
VisualDSP++ 2.0 features and usage.
VisualDSP++ 2.0 Assembler
and Preprocessor Manual for
ADSP-21xxx DSPs
Assembler function and commands for
SHARC family DSPs
VisualDSP++ 2.0 C/C++
Complier and Library Manual
for ADSP-21xxx DSPs
Complier function and commands for
SHARC family DSPs
VisualDSP++ 2.0 Linker and
Utilities Manual for ADSP-
21xxx DSPs
Linker function and commands for the
SHARC family DSPs
! Important: If you plan to use the EZ-KIT Lite board in conjunction with
a JTAG emulator, refer to the documentation that accompanies the
emulator.
ADSP-21160 EZ-KIT Lite Evaluation System Manual 1-5

2 GETTING STARTED
2.1 Overview
This chapter provides the information you need to begin using ADSP-21160 EZ-KIT Lite
evaluation system. For correct operation, install the software and hardware in the order
presented in section 2.4. This chapter has the following sections:
• Contents of Your EZ-KIT Lite Package (Section 2.2)
Provides a list of the components that are shipped with this EZ-
KIT Lite evaluation system.
• PC Configuration (Section 2.3)
Describes the minimum requirements for the PC to work with the
EZ-KIT Lite evaluation system.
• Installation Tasks (Section 2.4)
Describes the step-by-step procedure for setting up the hardware
and software.
2.2 Contents of Your EZ-KIT Lite Package
Your ADSP-21160 EZ-KIT Lite evaluation system package contains the
following items.
• EZ-KIT Lite Quick Start Guide
• ADSP-21160 EZ-KIT Lite board
• VisualDSP++ CD with license.
• ADSP-21160 EZ-KIT Lite CD, containing:
o EZ-KIT Lite specific debug software
o USB driver files
o Example programs
o ADSP-21160 EZ-KIT Lite Evaluation System manual (this document)
o Flash Programmer Utility
• Installation Quick Reference Card for VisualDSP++
• Universal 7.5V DC power supply
• 5-meter USB type A to type B cable
• Registration card – please fill out and return
If any item is missing, contact the vendor where you purchased your EZ-KIT Lite
evaluation system or contact Analog Devices, Inc.
ADSP-21160 EZ-KIT Lite Evaluation System Manual 2-6

2.3 PC Configuration
For correct operation of the VisualDSP++ software and the EZ-KIT Lite
hardware, your computer must have the minimum configuration shown in Table
2-1.
Table 2-1: Minimum PC Configuration
Windows98, Windows2000 or later
Intel (or comparable) 166 MHz processor
VGA Monitor and color video card
2-button mouse
50 MB free on hard drive
32 MB RAM
Full-speed USB port
CD-ROM Drive
! NOTE: This EZ-KIT Lite evaluation system does not run under
Windows 95 or Windows NT.
2.4 Installation Tasks
The following tasks are provided for the safe and effective use of the
ADSP-21160 EZ-KIT Lite evaluation system. Follow these instructions in the
order presented to ensure correct operation of your software and hardware.
1. VisualDSP++ software installation
2. VisualDSP++ license installation
3. EZ-KIT Lite debug software installation
4. EZ-KIT Lite hardware setup
5. EZ-KIT Lite USB driver installation
6. USB driver installation verification
7. VisualDSP++ startup
2.4.1 Installing the VisualDSP++ Software
This EZ-KIT Lite evaluation system comes with the latest version of
VisualDSP++ for the SHARC DSP family. You must install VisualDSP++ before
installing the EZ-KIT Lite debug software.
Insert the VisualDSP++ disc into the CD-ROM drive. If Auto Run is enabled on
your PC, the home screen of the VisualDSP++ install wizard will automatically
appear. If not, choose Run from the Start menu, and enter D:\Setup.exe in the
Open field, where D is the name of your local CD-ROM drive. Click on the
Install VisualDSP++ option. This will launch the setup wizard. Follow the on-
screen instructions.
ADSP-21160 EZ-KIT Lite Evaluation System Manual 2-7

2.4.2 Installing the VisualDSP++ License
Before the VisualDSP++ software can be used, the license must be installed.
To install the VisualDSP++ license:
1. Ensure that VisualDSP++ has been installed.
2. Insert the VisualDSP++ disc into the CD-ROM drive if it is not already in
the drive.
3. At the home screen of the VisualDSP++ install wizard, select the Install
License option.
4. Follow the setup wizard instructions.
! NOTE: You will need the serial number located on the back of the disc
sleeve.
2.4.3 Installing the EZ-KIT Lite Debug Software
VisualDSP++ communicates with the EZ-KIT Lite board using the EZ-KIT Lite
debug software. This software is supplied on the EZ-KIT Lite CD-ROM.
To install the EZ-KIT Lite debug software:
1. Ensure that VisualDSP++ has been installed.
2. Close all Windows applications. The install will not work correctly if any
VisualDSP++ applications are running.
3. Insert the EZ-KIT Lite disc into the CD-ROM drive. If Auto Run is
enabled on your PC, the home screen of the EZ-KIT Lite install wizard
will automatically appear. If not, choose Run from the Start menu, and
enter D:\Setup.exe in the Open field, where D is the name of you local
CD-ROM drive. Click the Install EZ-KIT Lite Software option. This
will launch the setup wizard. Follow this wizard with the on-screen
instructions.
2.4.4 Setting Up the EZ-KIT Lite Hardware
The EZ-KIT Lite evaluation system contains ESD (electrostatic
discharge) sensitive devices. Electrostatic charges readily
accumulate on the human body and equipment and can
discharge without detection. Permanent damage may occur on
devices subjected to high-energy discharges. Proper ESD
precautions are recommended to avoid performance degradation
or loss of functionality. Store unused EZ-KIT Lite boards in the
protective shipping package.
The ADSP-21160 EZ-KIT Lite board is designed to run outside your personal
computer as a stand-alone unit. You do not have to open your computer case.
To connect the EZ-KIT Lite board:
ADSP-21160 EZ-KIT Lite Evaluation System Manual 2-8

1. Remove the EZ-KIT Lite board from the package. Be careful when
handling the board to avoid the discharge of static electricity, which may
damage some components.
2. Figure 2-1 shows the default jumper settings, DIP Switch, connector
locations, and LEDs used in installation. Confirm that your board is set up
in the default configuration before continuing.
Figure 2-1: EZ-KIT Lite Hardware Setup
3. Plug the provided power supply into P4 on the EZ-KIT Lite board.
Visually verify that the green power LED (LED6) is on. Also verify that
the two red reset LEDs (LED1 and LED8) go on for a moment and then
go off.
ADSP-21160 EZ-KIT Lite Evaluation System Manual 2-9

4. Connect the USB cable to an available full-speed USB Port on your PC
and to P7 on the ADSP-21160 EZ-KIT Lite board.
2.4.5 Installing the EZ-KIT Lite USB Driver
The EZ-KIT Lite evaluation system can be installed on Windows 98, Windows
2000, And Windows XP and requires one full-speed USB port. Section 2.4.5.1
describes the installation on Windows 98. Sections 2.4.5.2 describes the
installation under Windows 2000. Section 2.4.5.2 describes the installation on
Windows XP.
2.4.5.1 Windows 98 USB Driver Installation
The Windows 98 USB driver must first be installed before using the ADSP-21160
EZ-KIT Lite evaluation system for the first time.
To install the USB driver:
1. Insert the EZ-KIT Lite disc into the CD-ROM drive.
The connection of the device to the USB port will activate the Windows 98 “Add
New Hardware Wizard” as shown in Figure 2-2.
Figure 2-2: Add New Hardware Wizard
2. Click Next.
ADSP-21160 EZ-KIT Lite Evaluation System Manual 2-10

3. Select Search for the best driver for your device as shown in Figure 2-3.
Figure 2-3: Search for the Driver
4. Click Next.
5. Select CD-ROM drive as shown in Figure 2-4.
Figure 2-4: Search the CD-ROM
6. Click Next.
ADSP-21160 EZ-KIT Lite Evaluation System Manual 2-11

Windows 98 will locate the WmUSBEz.inf file that is on the CD-ROM as shown
in Figure 2-5.
Figure 2-5: The Driver is Located
7. Click Next.
The Copying Files dialog box appears (Figure 2-6).
Figure 2-6: Search for .sys File Dialog Box
8. Click Browse.
ADSP-21160 EZ-KIT Lite Evaluation System Manual 2-12

Figure 2-7 will appear.
Figure 2-7: Open the .sys File
9. In Drives select your CD-ROM drive.
10. Click OK.
Figure 2-8 will appear.
Figure 2-8: Copying Files Dialog Box
11. Click OK.
ADSP-21160 EZ-KIT Lite Evaluation System Manual 2-13

The driver installation is now complete as shown in Figure 2-9.
Figure 2-9: Finish the Software Installation
12. Click Finish to exit the wizard.
Verify the installation by following the instructions in section 2.4.6.
ADSP-21160 EZ-KIT Lite Evaluation System Manual 2-14

2.4.5.2 Windows 2000 USB Driver Installation
The Windows 2000 USB driver must first be installed before using the
ADSP-21160 EZ-KIT Lite evaluation system for the first time.
To install the USB Driver:
1. Insert the EZ-KIT Lite disc into the CD-ROM drive.
The connection of the device to the USB port will activate the Windows 2000
“Found New Hardware Wizard” as shown in Figure 2-10.
Figure 2-10: Found New Hardware Wizard
2. Click Next.
ADSP-21160 EZ-KIT Lite Evaluation System Manual 2-15