Angel Line Madison 6 Drawer Double Dresser User manual

Madison 6 Drawer Double Dresser
Instruction Manual
Read all instructions before assembly and use.
Small parts may present choking hazard prior to assembly.
Keep out of reach of children until assembly is complete.
KEEP INSTRUCTIONS FOR FUTURE USE.
ADULT ASSEMBLY REQUIRED.
Made in Vietnam

WARNING
ASSEMBLY, CARE AND MAINTENANCE
LIMITED ONE YEAR WARRANTY
Serious or fatal crushing injury can occur from furniture tip-over. To help prevent tip-over:
do not
Never
Never
Use of tip-over restraints may only reduce, but not eliminate, the risk of tip-over.
Do not
Do not
- Install tip-over retrain provided.
- Place heaviest items on the lowest drawers.
- Unless specifically designed to accommodate, set Tv’s or other heavy objects on the top of
this product.
- allow children to climb or hang on drawers, doors or shelves.
- open more than one drawer at a time.
- Always monitor your child’s activity when in the nursery.
- allow standing in drawers.
- allow standing on top of this product.
- Accessory items must be securely fastened to this product according to the instructions provided
with those items.
- To avoid head injury, do not allow children to play underneath open drawers.
- Do not leave drawers open when in use.
CAUTION: Do not use a power screwdriver as it can cause screws to break or strip.
Do not
- To protect finished parts during assembly, please place them on a soft, non-abrasive surface to
avoid damaging the finish.
- Care should be taken when unpacking and assembling the product.
- Inspect the product periodically, contact Longwood Forest Products for replacement parts or
questions.
- Do not store this product or any parts in extreme temperatures and conditions such as hot attic or
a damp, cold basement..
- To clean surface, use only water on damp cloth then a dry cloth to preserve the original finish.
- use abrasive chemicals or window cleaners as it will scratch the surface and could
damage the protective coating.
- Lift product when moving on carpeting to prevent leg breakage.
- Avoid using a vaporizer near furniture as it will cause wood to swell and finish to peel.
Your product is warranted against defects in workmanship or material for ONE YEAR from the date
of purchase. This warranty shall be limited to repairing or replacing any part of the product which, in
the opinion of the company, shall be proved defective in materials or workmanship under normal
use and service during the one year warranty period. During the one year warranty period, repair or
replacement pf parts shall be made at no charge. Date of purchase of the product must be
established by production of your sales slip or other satisfactory evidence.
Please do not return the product to the store where it was originally purchased as they do not stock
replacement parts. When calling our customer service department, make sure to have the model
number and date of manufacture readily available.
DISTRIBUTED BY:
Longwood Forest Products, Inc.
88 Industrial Park Rd, Pennsville, NJ
Customer Support
Tel: [phone]
email: [email protected]

BACK PANEL TOP CROSS RAIL BOTTOM CROSS RAIL
RIGHT SIDE PANEL
MIDDLE PANEL
MIDDLE CROSS RIAL
LEFT SIDE PANEL SUPPORT POST TOP PANEL
TOP BACK PANEL
UPPER & LEFT DRAWER FRONT
UPPER & RIGHT DRAWER FRONTL
UPPER LEFT DRAWER SDIE
UPPER RIGHT DRWER SIDE
DRAWER BOTTOM PANEL

UPPER DRAWER BACK LOWER & LEFT DRAWER FRONT
LOWER & RIGHT DRAWER FRONT
LOWER & DRAWER LEFT SIDE
LOWER & DRAWER RIGHT SIDE
LOWER DRAWER BOTTOM

- Thread 6 CAM BOLTs (1) to middle of BACK PANEL (A), TOP CROSS RAIL (B), BOTTOM CORSS
RAIL (C), and MIDDLE CROSS RAIL (D).

- Insert 2 CAM LOCKS (3) to MIDDLE PANEL (E). (make sure cam arrow is pointing
to short edge)
- insert 3 WOOD DOWELS (2) into TOP CROSS RIAL (B), AND BACK PANEL (E).
- Attach BACK PANEL (A) AND TOP CROSS RIAL (B) to MIDDLE PANEL (E) BY TURNING
CAM CLOCKWISE.

- Insert 4 CAM LOCKS( 3) to MIDDLE PANEL (E).
- Insert 2 WOOD DOWELS (2)
- Attach 2 TOP CROSS RAILSES (B), 2 MIDDLE CROSS RAILS (D), and BOTTOM RAIL (C)
by turning the cmas clockwise.

- Thread 20 CAM BOLTS (1) to LEFT PANEL (F), RIGHT PANEL (G), and TOP PANEL (I)
20

- Insert 14 CAM LOCKS (3) to 2 TOP CROSS RAILS (B), 2 MIDDLE CROSS RAILS (D), and BOTTOM
CROSS RAIL (C).
- Insert 14 WOOD DOWELS (2) into ends of 2 TOP CORSS RIALS (B), 2 MIDDLE CROSS RIALS (D), and
BOTTOM CROSS RAIL (C).
- Attach LEFT PANEL (G), and RIGHT PANEL (F) to partially assembled unit by turning the CAM
LOCK (3) clockwise.

- Attach SUPPORT LEG (H) to MIDDLE PANEL (E) with 1 BOLT (4) and 2 WOOD
DOWELS (2) as shown. (Use ALLEN KEY (5) to tighten the bolt.)
NOTE - The SUPPORT LEG (H) and SIDE PANELS (G & F) are equipped with
adjustable levelers. Once assembly is coplete and the unit is in the
desired location, rotate the adjustable clockwise or counterclockwise
until it rests evenly on the oor.

7
- Insert 6 CAM LACKS (3) and 6 WOOD DOWELS (2) in LEFT SIDE PANEL (G), RIGHT SIDE PANEL
(F), MIDDLE PANEL (E).
- Carefully position the TOP PANEL (I) over assembly and lock into place using the locatin
WOOD DOWELS (2).
- Attach TOP PANEL (I) to LEFT PANEL (G), RIGHT SIDE PANEL (F), and MIDDLE PANEL (E) by
turning the cams clockwise.
- Insert 4 WOOD SCREWS (6) into BOTH TOP CORSS RAILS (back and front) and attach to
TOP PANEL (I).

10
- Attach TOP BACK PANEL (J) TO BACK OF CHST JUSING 16 ROUND HEAD SCRES (7).

- Position and attach UPPER LEFT DRAWER SIDE (M),
and UPPER RIGHT DRAWER SIDE (N) by using 4 OF 1”
(25mm) SCREWS (6) provided to UPPER LEFT
DRAWER FRONT (K).
9
- Carefully slide DRAWER BOTTOM (0)
into grooves of DRAWER SIDES and
DRAWER FRONT.
- Position and attach DRAWER BACK (P)
to DRAWER SIDES using 4 of 1”(25mm)
screws (6) providevd.
- Repeat same step for upper right side drawer.

10
- Position and attach LOWER LEFT DRAWER SIDE (S),
and LOWER RIGHT DRAWER SIDE (T) by using 4 OF 1”
(25mm) SCREWS (6) provided to LOWER LEFT
DRAWER FRONT (Q).
- Carefully slide DRAWER BOTTOM (0)
into grooves of DRAWER SIDES and
DRAWER FRONT.
- Position and attach LOWER DRAWER BACK (U)
to DRAWER SIDES using 4 of 1”(25mm)
screws (6) providevd.
- Repeat same steps for lower right side drawer.

- Assemble the drawers tothe case as per below conguration.
- Holding the drawer on a downward sloping angle, rest of drawer sides to the
correspoinding drawer runners pre-assembled
- Carefully push the drawer forward makin sure the rollers are. inside the track.
- Assemble the rest of the drawers.
- Position dresser in your room
and install tip-over restraint as per
instructions included in the hardware kit.

1-844-441-1112