Anova DM600 User manual

Instructions - User Manual
HAMMER BRUSH CUTTER
DM600
Millasur, SL.
Rúa Eduardo Pondal, nº 23 - Pol. Ind. Sigüeiro
15688 - Oroso - A Coruña - 981 696 465 www.millasur.com

2
ANOVAthanks you for choosing one of our products and guarantees theassistance and
cooperation that has always distinguished our brand over time.
This machine is designed to last for many years and to be of great use if used in
accordance with the instructions contained in the user manual. We therefore recommend
that you read this instruction manual carefully and follow all our recommendations.
For more information or questions you can contact us through our web supports such as
www.anova.es or www.millasur.com
INFORMATION ABOUT THIS MANUAL
Please pay attention to the information provided in this manual and on the appliance for
your safety and that of others.
•This manual contains instructions for use and maintenance.
•Take this manual with you when you go to work with the machine.
•The contents are correct at the time of printing.
•The rights to make changes at any time are reserved without affecting our legal
responsibilities.
•This manual is considered an integral part of the product and must remain with it
in case of loan or resale.
•Ask your dealer for a new manual in case of loss or damage.
READ THIS MANUAL CAREFULLY BEFORE USING THE MACHINE
To ensure that your machine provides the best results, please read the
usage and safety regulations carefully before using it.
OTHER WARNINGS:
Incorrect use could cause damage to the machine or other objects.
The adaptation of the machine to new technical requirements could cause differences
between the content of this manual and the purchased product.
Read and follow all instructions in this manual. Failure to follow these instructions could
result in personal injury.
Always keep the instruction manual as important information.

3
Important safety rules
1) Before using the machine, please read the instructions carefully and follow the
instructions in the instruction manual for starting, adjustment and maintenance.
2) Before using the machine, pay attention to the following items:
- Check the crankcase and transmission case for oil leaks; engine oil and the
quality of engine oil in the crankcase and transmission case. Replace clean
new oil in time
- Check whether the lubrication parts are well lubricated.
- When refueling, pay attention to the fuel tank which must be filled with clean
fuel. The fuel must be filled with the engine stopped and well ventilated.
Please note that the fuel must not come into contact with hot surfaces,
electrical components or rotating parts.
- Avoid overflow, check if the fuel overflows or leaks. In case of overflow, dry
the machine as soon as possible. Tighten the cap once filled.
- Do not have fireworks nearby to avoid fires.
- Check if the moving parts are loose, chafed or stuck; if the direction of
rotation is consistent with the marking direction.
- Check whether the exposed rotating parts and moving parts have reliable
safety protection devices and safety signs.
- Check that the clutch and other working parts are free of cracks, distortion
and excessive wear.
- If there is any abnormality, it should be fixed before trial operation. There
should be no obvious rubbing, abnormal sounds and vibrations during the
test run. The speed must meet the requirements and speeding work is not
allowed. When replacing the parts involved in safety, work should be done
under the requirements of the instructions or the direction of a professional
maintenance person.
3) Minors and those who have not been trained to master the rules for the use of this
machine cannot work with it.
4) The machine cannot be used after drinking or with excessive illness/fatigue.
5) The operator must tighten clothing and fists when operating, and in case of long
hair, wear a protective cap.
6) When the machine is working, the parts that affect safety and operation should not
be modified by yourself. It is not allowed to disassemble or shorten the protective
cover of each part, and the operator must concentrate on the operation.
7) You can only start the machine under the confirmed safety condition. After cold

4
start, heavy loads are not allowed immediately, especially for new machines or
overhauled machines.
8) Driving on cement, slate or stone piles with rotating blades is not allowed. In rotary
tillage operation, attention should be paid to avoid collision with hard objects such
as stones, to avoid damaging the rotary blade.
9) During operation, pay attention to the working condition and sound of each part,
check whether the connection of each part is correct, and do not let it loose. If there
are conditions such as abnormal sound, the machine should be stopped and
checked immediately, and it is not allowed to remove the fault when the machine
is running.
10)Prevent the machine from tipping over during work.
11)Reversing is not allowed with the disposer running.
12)When working, pay attention to see if there is oil leakage from the transmission
case, engine and other parts. If so, stop the machine for inspection. Pay attention
not to use open fire to avoid fire.
13)Troubleshooting in time to avoid environmental pollution, which affects product
safety.
14)When removing grass and breaking mud, the power should be cut off first, and
then remove it after the machine stopped. It is not allowed to remove the blockage
of the mower by hand or with an iron rod when the machine is running.
15)After use, dirt, weeds, oil and other accessories must be removed from the
machine.
16)Regularly check blade bolts, bearings and other moving parts for looseness or
damage.

5
Security warning content
Training
a) Please read the operating and maintenance instructions carefully to be fully
familiar with all operating mechanisms and methods for operating the machine.
Master how to quickly stop and separate the operating mechanism.
b) Children can never use the machine. Adults who don't read the instructions don't
either.
c) Keep the work area attended, free of children and pets.
Preparation
a) Thoroughly inspect the area that will use the machine and remove any debris.
b) Disengage all clutches and put in neutral before starting the engine.
c) Do not operate the machine without wearing a suitable jacket. Wearing non-slip
shoes will improve stability on the slippery surface.
d) Handle fuel with care, it is flammable.
e) Use a suitable container to store fuel.
f) Do not add oil to the fuel tank while the engine is running or when the engine is
hot.
g) In case of refueling, it should be done outdoors and carefully, do not refuel indoors.
h) Before you begin, tighten the fuel tank cap and wipe up any spilled fuel.
i) When the engine is running, do not make any adjustments (except special
adjustments recommended by the manufacturer).
j) Safety glasses must be worn for any handling such as preparation, operation and
maintenance.
Handling
a) Hands and feet must not be placed near rotating parts or under rotating parts.
b) When maneuvering (or crossing) gravel pavements, sidewalks or paths should be
especially careful, guard against potential hazards, pay attention to traffic
conditions and not carry passengers.
c) After hitting the debris, stop the engine, carry out a thorough inspection to check
whether the machine is damaged, it must be repaired before restarting and
handling.
d) Always pay attention to your feet and avoid slipping or falling.
e) Once the machine has abnormal vibration, please stop the engine immediately to
find the reason. Vibration is often a precursor to the problem.
f) If the machine stops, the cleaning blade is blocked. For maintenance, adjustment
or inspection, the engine must first be stopped.
g) When the machine is unmanned, take all possible precautions: separate the PTO
shaft, lower the attachment, turn the engine to neutral stop and remove the key
from the switch.
h) Before cleaning, repairing or inspecting the machine, the engine must be stopped
and all moving parts must be stopped.

6
i) Engine exhaust gas is harmful and must not be operated indoors.
j) Do not operate machine without factory covers and guards.
k) Keep away from children and pets.
l) Do not overload the machine by going too deep into the ground you are working
on (the machine cuts the brush shallowly).
m) The machine must not run at high speed on slippery surfaces. It should not work
on steep slopes.
Caveat: Do not use at more than 12º incline.
n) Spectators are never allowed to get close to the machine.
o) Use only accessories and equipment permitted by the manufacturer (for example,
counterweights, cabins, etc.).
p) Do not operate the machine when the field of vision is not good or the light is not
sufficient.
q) When the machine is used, it should be prevented from tipping over.
repair and storage
a) Keep the machine, accessories and equipment, including batteries, in safe
working condition. If possible, remove the battery and store it to prevent it from
freezing and charge it if necessary.
b) Check the tightness of the bolts so that they are in safe working condition.
c) The machine should be stored indoors and away from fire
d) The motor must cool down before being stored indoors.

7
security symbols

8
Index
1. Technical data of the machine
2. Installation method
3. Instructions for use
4. Precautions for use
5. Maintenance
6. Adjustment methods
7. Troubleshooting
8. Scope
9. Environment
10. Exploded view
11. Certificate of Conformity (CE)

9
1. Technical data of the machine
Data sheet
This product is suitable for cutting weeds in mountainous areas, drylands, wastelands,
greenhouses and orchards.
DM600
Motor
Gasoline
Transmission system
strap system
clutch system
tension wheel
Start System
Manual
working width
600mm
Rotary blade radius
≥ 30
machine size
1720x900x700
speeds
1 front and 2 rear
reverse speed
16rpm
Rotating Blade RPM
2820rpm
machine parts
clutch blades
front wheels
Blade
cover
Rear
wheels
handlebar
frame
throttle switch
Gear lever
Motor
Shock
Protection
wheel
carrier
lifting
handle

10
2. Installation method
Assembly after unpacking
- Install the handlebar: install the handlebar on the handlebar seat and lock the bolt.
- Adjust the clutch handle according to the proper position.
Cable Installation and Adjustment
Clutch Cable Adjustment
1) Screw the adjusting bolt on both sides of the clutch cable ends into the clutch
handle and clutch rocker arm bolt hole.
2) Insert the head of the clutch rocker arm cable into the opening bolt slot.
3) Adjust the bolts at both ends of the clutch cable to tighten it.
4) Adjust the clutch cable several times until the clutch can be separated by the clutch
handle.
Verification and replacement
1) Check if the connection bolt is loose; tighten it if it is.
2) Check if all the handles in the control system (throttle, reduced pressure, reverse
handle, etc.) are flexible and in place.
3) Put the gearbox lever in the neutral position.
4) Add oil:
a. Add SAE10W-40 or similar lubricating oil to the crankshaft of the gasoline
engine.
b. Add 20# lubricating oil into the gearbox, make the machine level, and inject
from the oil hole above the gearbox. When checking the oil level, insert the
dipstick (Note: Do not rotate the dipstick), the oil level should be between
the upper and lower limits.
5) Add 92# gasoline into the fuel tank (For details, please refer to the engine user
manual).
Oil stick
Upper level
Lower level