Anova BRP300 User manual

anovafurnishings.com
888.535.5005 tel
ASSEMBLY INSTRUCTIONS
BRP300 7 Bike Rack
BRPVC300 7 Bike Rack
BRP304 7 Bike Rack
BRP305 9 Bike Rack
BRPTRI305 9 Bike Rack
TOOLS NEEDED
Ratchet with 9/16” Socket•
9/16” Open-end or Box-end Wrench•
12 x
3/8”
Flanged Nut
12 x
3/8” X 1.5”
Hex Head Bolt
ASSEMBLY:
NOTE: Before assembling the Nuts to the Bolts, it is recommended that a light oil or petroleum jelly be applied to the Bolt threads.
1. Inspect the shipping container contents for damage and to determine that all components and hardware are present.
2. Place the Inner Rack on the packaging cardboard or other so surface. Position one of the Rack Ends near one end of the Inner
Rack.
3. Align the upper mounting holes in the end of one of the Rack Ends with the upper mounting holes of the Inner Rack. Install a Flat
Washer onto one of the Hex Head Bolts and insert the Bolt through both parts. Install a Flat Washer and Flanged Nut on the end of
the Bolt and tighten nger tight so adjustments can be made during assembly.
Install a Bolt and Washer through each of the other sets of mounting holes in that end of the Inner Rack and Rack End bracket and
secure each Bolt with a Flat Washer and Flanged Nut.
ASSEMBLY HARDWARE:
For tamper resistant hardware see page 2
BENCH COMPONENTS:
1 x
Le End
Flat Washer
Hex Head Bolt
Hex Head Bolt
and Flat Washer
Model BRP304 shown.
Inner Rack and Ends vary
with models.
1 x
Inner Rack
(3.5” or 7.5” Spacing)
Packaging cardboard
or other so surface
OR
Inner Rack
Rack End
1 x
Support
1 x
Right End
24 x
3/8”
Flat Washer
Flat Washer
and Flanged Nut
Flat Washer
Flanged Nut
OR

Do not drag the assembled unit across any surface.•
This product requires only periodic cleaning with a sponge and a solution of mild detergent and water to•
remove surface dirt. Do not clean with a solvent or petroleum based products.
Furniture must not be used other than for its intended purpose and should be inspected regularly for loose,•
missing, or broken hardware, and general instability.
Furniture that is damaged or appears to be unstable must be removed from service and be repaired or replaced.•
Repairs must be made using only factory authorized parts and methods.•
WARNING
CARE AND
MAINTENANCE
211 North Lindbergh Blvd.
St. Louis, MO 63141
tel: [phone]
web: anovafurnishings.com
10/2012
Hex Head Bolt
and Flat Washer
Hex Head Bolt
and Flat Washer
Flat Washer
and Flanged Nut
Flat Washer
and Flanged Nut
Installing Tamper Resistant Hardware:
1. Orient the Breakaway Nut so the cone
shape is toward the Washer.
Breakaway
Nut Head Breakaway
Nut Cone
Washer
Washer
Bolt Head
Breakaway
Nut Cone
Washer
Washer
Bolt Head
Hex Head
Breaks O
2. Aer the fasteners have been
installed, torque the Breakaway
Nut using the Rachet with
3/4” Socket until the Hex Head
breaks o.
TOOLS NEEDED:
Ratchet with 3/4” Socket•
9/16” Open-end or Box-end Wrench•
IF YOU PURCHASED A MODEL WITH TAMPER RESISTANT HARDWARE:
HARDWARE:
12 x
3/8”
Breakaway Nut
12 x
3/8” X 1.5”
Hex Head Bolt
24 x
3/8”
Flat Washer
4. Attach the other Rack End to the other
end of the Inner Rack in the same
manner, installing the 1.5” long Bolts
from the top. Use a wrench to tighten
the hardware aer all Bolts are installed.
5. Install the Support using a Bolt with Washer in each mounting
hole and secure each Bolt with a Flat Washer and Flanged Nut.
6. Tighten all of the hardware and move the Bike Rack to the desired location.
7. Two weeks aer installation, retighten all hardware.