Anstel Babyrest KAYA CHEST User manual

KAYA CHEST
Assembly Instructions
- The manufacturer's assembly instructions must be followed be followed in detail to ensure the safety features
of the chest are not compromised.
- To clean the surface, use a damp cloth with water. Do not use window cleaners or cleaning abrasives as this
may scratch the surface and could damage the protective coating.

1 TOP PANEL
(1PC)
Box 1/3 Parts
5 CENTER RAIL
(2PCS)
6 UPPER BACK PANEL
(1PC)
7 LOWER BACK PANEL
(1PC)
8 BOTTOM PANEL
(1PC)
9 LEG
(4PCS)
13 DRAWER BASE
(3PCS)
HARDWARE BAG
(1PC)
4 TOP RAIL
(1PC)

WARNING
Do not allow children to
climb
o
n
this furniture -
it may topple over
and badly injure a child.
Do not place toys or
other child
appealing items on top
of this
furnitur
e
WARNING
Do not allow children to climb on
this furniture - it may topple over
and badly injure a child.
Do not place toys or other child
appealing items on top of this
furniture
REFER TO THE WARNING
LABEL FOR IMPORTANT
SAFETY INFORMATION
Warning
Do not allow children to
climb
o
n
this furniture -
it may topple over
and badly injure a child.
Do not place toys or
other child
appealing items on top
of this
furnitur
e
Box 2/3 Parts
2 SIDE PANEL (L)
(1PC)
3 SIDE PANEL (R)
(1PC)
Box 3/3 Parts
10 DRAWER BACK
(3PCS)
11 DRAWER SUPPORT
(3PCS)
12 DRAWER SIDE
(6PCS)
14 DRAWER FRONT
(3PCS)
Please place the hangtag on visible area of the chest after complete
assembly of the chest

A B CD
ANCHORING CHEST
To anchor your chest, use the anchor kit as seen in the diagram below. Choose a suitable wall fixing
that matches your wall style and then fasten the strap to the wall as shown using appropriate fixings.
COMPLETED ASSEMBLY
Babyrest™
by Anstel Brands Pty Ltd
36 Sunline Drive
Truganina VIC 3029 Australia
[phone]
[email protected]
Made in Malaysia
PART LIST
NO DESCRIPTION QTY NO DESCRIPTION QTY
1TOP PANEL 1 8BOTTOM PANEL 1
2SIDE PANEL (L) 19LEG 4
3SIDE PANEL (R) 110 DRAWER BACK 3
4TOP RAIL 1 11 DRAWER SUPPORT 3
5CENTER RAIL 2 12 DRAWER SIDE-3L3R 6
6UPPER BACK PANEL 1 13 DRAWER BASE 3
7LOWER BACK PANEL 1 14 DRAWER FRONT 3
HARDWARE LIST
NO DESCRIPTION QTY
AWOOD DOWEL M8 49
B MINIFIX 17
C MINIFIX CAP 17
D SCREW M4 X 32MM 48
E ALLEN KEY M4 1
F JCBC M6X70MM 8
GSPRING & FLAT WASHER 8
H HANDLE WITH SCREW 3
1
B
B
B
23
A
B
AA
BBB
A
B
A
A
B
B
B
4
5
5
AAA7
8
14
x 3PCS
x 3PCS
Read this instructions carefully. See hardware and furniture part list for guidance. Be sure all part is complete before
you assemble. Place all wooden furniture part on a clean and flat soft surface to prevent from being scratched.
Follow the figure to start assembling.
CAUTIONS:
1. Do not FULLY-TIGHTEN the nut or nut bolt until all nut or bolt is ready assembled.
2. Do not OVER-TIGHTEN the nut or nut bolt to avoid causing damages to the thread.
3. Keep all hardware part out of reach of children.
NOTE : THE LIST AND QUANTITY SHOWN ARE FOR 1 UNIT ASSEMBLY.
A
AA
AA
AA
AAA
AAA
10
AAAA
AAAA
B
B
A
A
A
6
A
A
C
D
B
Step 1 : Attach fittings to timber parts
PHILLIPS SCREW DRIVER REQUIRED. FOR QUICKER ASSEMBLY, WE
RECOMMEND THE USE OF A POWER DRILL ON A LOW-SPEED SETTING.
G2G1

Step 2 : Fit front bars to Left side panel "2". Make sure matching paint
colour is facing front of chest.
4
5
D
D
2
5
D
Step 3 : Attach rear panels "6" and "7"
LOCK CLOCKWISE
CC
CC
67
Step 8 : Drawer assembly x 3
12
10
11
12
C
DD
D
13
D
D
D
D
C
H
H
H
LOCK CLOCKWISE
D
D
14
D
Top
Bottom
Painted side
3 holes for B to
face top of chest
Step 9 : Insert Drawers into Cabinet
1) Bring the ball bearing retainer on cabinet forward.
2) With help from another person, carefully align
and insert drawer slide into cabinet slide, guiding
the drawer slide between the ball bearing retainer,
as shown
3) Push the drawer into cabinet. You may experience
a light resistance when pushing the drawer into cabinet,
but once both slides are properly engaged, drawer
should slide in and out smoothly. Push forward to
closed position and then back out again.
Note.
*Do not use excessive force to insert drawer as this may cause
damage to the slides.
*Make sure the drawer with warning label is placed in top drawer position.
To Remove Drawer, If Needed
·Pull the drawer fully open so levers are visible.
·Push UP on left side lever and DOWN on right side lever.
·Holding levers in place, pull drawer toward you.
1) 3)
2)
Left Side Right Side
Disconnect Levers

Step 4 : Attach bottom panel "8"
D
8
D
D
D
Step 5 : Attach Right side panel "3"
LOCK CLOCKWISE
D
D
D
3
C
C
CC
D
D
D
D
D
D
Step 6 : Attach top panel "1"
Step 7 : Attach feet section
LOCK CLOCKWISE
C
C
C
C
DDD
DDD
D
D
D
D
1
9
D
D
D
E
F
G1
G2
EF
G1
D
9
9
9
G2
Painted
edge
facing
front