Anthropologie Lombak User manual

Lombak Single Vanity
Assembly Instructions
Page 1 of 4Rev 1 05.10.19
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2019 UO, Inc. All rights reserved, including all applicable copyright, design and patent rights. Any
unauthorized reproduction, adaptation, distribution or other infringement will be prosecuted.
Do not throw away packing materials and carton until after assembly.
Assemble all parts on a clean smooth surface
Care Instructions:
Avoid direct exposure to sunlight. Do not place over heat or Air conditioning vents.
Adjust levelers so that the furniture sits at on uneven oors.
Blot spills do not rub, with a clean white cloth.
Do not use harsh chemicals.
Before cleaning any part test a small spot in a hidden area.
You will need to Seek the help of a Professional Plumber for complete installation.
A. Vanity
1x
B. Top
1x
C. Sink
1x
D. Backsplash
1x

Lombak Single Vanity
Assembly Instructions
Page 2 of 4Rev 1 05.10.19
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2019 UO, Inc. All rights reserved, including all applicable copyright, design and patent rights. Any
unauthorized reproduction, adaptation, distribution or other infringement will be prosecuted.
READ ALL INSTRUCTIONS BEFORE ASSEMBLY!
1. Storage
A. Keep marble top in its crate until installation
B. Store Crate Vertically in a place safe from damage
C. Do not stack anything on top of the crate.
2. Opening Crate
A. Before unpacking make sure you are ready for installation and have all of the following.
1. 2 people to help lift the heavy top
2. Vanity installed according to instructions plumb to the wall and oor
3. Make sure the top is the correct one for the vanity
4. Tools and Materials:
A. Flat, non-abrasive work surface such as a blanket or cardboard
B. A level
C. Phillips head screwdriver
D. Caulk/Sealant
B. With help carefully Lay the crate down making sure that you do not drop it
This is the only time the crate should be horizontal.
C. Remove the metal bands.
D. Unscrew the slats/Lid and remove.
E. Examine the marble top for defects. Wipe clean with a soft cloth.

Lombak Single Vanity
Assembly Instructions
Page 3 of 4Rev 1 05.10.19
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2019 UO, Inc. All rights reserved, including all applicable copyright, design and patent rights. Any
unauthorized reproduction, adaptation, distribution or other infringement will be prosecuted.
3. Installation of marble top
A. Always use 2 people to move top.
B. Carry it Like the images shown below. Never carry it at.
Caution! Installation between two walls requires special care.
1. Instructions for installation between two walls.
A. Set top on its edge at the back of the vanity.
B. Lower the front of the marble top to the vanity, Make sure that both ends are lowered at the
same time.
C. Do not twist or turn the top as you lower it as this can break or crack the top.

Lombak Single Vanity
Assembly Instructions
Page 4 of 4Rev 1 05.10.19
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2019 UO, Inc. All rights reserved, including all applicable copyright, design and patent rights. Any
unauthorized reproduction, adaptation, distribution or other infringement will be prosecuted.
Before you begin:
Professional installation is required for this vanity. Install all water supply and drain piping according to local
pluming and building codes. Insure that the wall and oor are square at the site of installation.
Tools and Materials:
A. Flat, non-abrasive work surface such as a blanket or cardboard
B. A level
C. Phillips head screwdriver
D. Caulk/Sealant
1. Place the Sink (C) onto the support bars of vanity (A). The overflow of Lavatory sink should be on the
same side as pre-drilled faucet holes on the stone top.
2. Apply a continuous bead of caulk/sealant to the top surface of rim of sink where it will contact
underside of Marble top.
3. Using two people, lift Marble top (A), carefully place it in position on top of vanity. Make sure the sink
lines up with the top. Press rmly down onto the sink.
4. Apply silicone sealant to bottom and back of backsplash and attach to wall and marble top.
5. Professional Plumber required to attach faucet and drain.