ANTTEQ AG24 User manual

AG24

PRECAUTIONS AND REMINDERS
IMPORTANT SAFETY INSTRUCTIONS
BUTTON CONTROL AND PERIPHERAL CONNECTION
OPERATING INSTRUCTIONS
SPECIFICATIONS
TROUBLESHOOTING
TABLE OF CONTENTS

IMPORTANT SAFETY INSTRUCTIONS
literature accompanying this
Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio, and the double-D
symbol are trademarks of Dolby Laboratories Licensing Corporation.

PRECAUTIONS AND REMINDERS
If you plan to clean the product. Unplug the TV, use soft fabric.
Never use water or chemicals.
High voltages are used in the operation of this product.
Do not open the product’s casing. Refer servicing to
qualified service personnel.
Never stand on, lean on or suddenly push the product or its stand.
You should pay special attention to children.
To prevent fire or electrical shock hazard, do not expose the
main unit to moisture. Do not place objects filled with liquids,
such as vases, on the TV.
Do not place the main unit on an unstable cart stand, shelf or table.
Serious injury to an individual, and damage to the television,
may result if it should fall.
Do not drop or push objects into the television cabinet slots or
openings. Never spill any kind of liquid on the television receiver.
When the product is not used for an extended period of time, it is
advisable to disconnect the AC power cord from the AC outlet.
Do not block the ventilation holes in the back cover.
Ventilation is essential to prevent failure of electrical
components.
Avoid exposing the main unit to direct sunlight and other sources
of heat. Do not install the television receiver directly on other
products which give off heat. Do not place direct heat sources,
such as lighted candles on the television.
If the television is to be built into a compartment or similar
enclosure, the minimum distances must be considered.
Heat build-up can reduce the usability your television.
Nevertheless, it can be dangerous.
Note: the use of apparatus must be in moderate climates.
Do not trap the power supply cord under the television receiver.

BUTTON CONTROL AND PERIPHERAL CONNECTION
OLRTNOCNOTTUB
In the non-menu page,Under the menu page, press the left and
right keys to adjust the volume addition and subtraction.
In the standby mode, press the to turn on the TV.
In the boot state, long press the to shut down.
In the non-menu page, you can adjust the TV channel under the
program addition and subtraction;
Under the menu page, you can move the cursor up and down.
Under the menu page , function equivalent to the OK key.
OK/
OK/
/OK
CH-/CH+
VOL-/VOL+
PERIPHERAL CONNECTION
2. Audio out terminal.
1. RJ45
3. Earphone terminal.
5. RF antenna.
.4 Audio&Video input terminal.
2 6 7 81 43 5 9 10 11
7. HDMI1 input terminal.
9. HDMI3 input terminal.
8. HDMI2 input terminal.
10.
6. LNB IN.
11. CI slot.

OPERATING INSTRUCTIONS
USING THE REMOTE CONTROL
Press 3 sec to stop:
USB recording,
Time Shift recording
5 sec backlight on/o
Start recording
Source
Press 3 sec for deep sleep
Ok
Hey Google
Back
Subtitles
Menu
Settings
Standby
Home
Channel list
Teletext
Play/Pause multimedia
Start/Pause
Time Shift recording
Audio
Stop multimedia &
TV media library
Remote pairing
Remote pairing
Displays EPG information

INITIAL SETUP
Please follow the instructions accordingly for the
rst setup.
This is an necessary function for the remote pair
control pair code. After pairing the code successfully,
you will have access on the remote control in order to
operate the TV. Please press and hold the ''HOME'' and
''LEFT'' buttons simultaneously for 5 seconds. Then
press the ''OK'' button. Eventually, the ''TV_BLE_
Remote'' displays in the upper right corner of the screen.
INPUT SOURCE
2. Press on the ''SOURCE'' button on the remote control
while on the LIVE TV source or press 2 times on the
''SOURCE'' button to be redirected directly for all the listed
input sources.
Open the google assistant or start a voice search.
The applications installed are displayed, the icons for
the favorite applications are shown inside here.
(favorite applications can be added, changed or deleted)
Apps: Icon to be redirected for all the listed applications
Notications: Display the notications
On-screen Menu: In order to navigate or congure
with convenience
Inputs: Icon to select an input source.
Network&Interent: Icon for network settings. (Wi)
Settings: Icon for the conguration of various settings.
For more detailed explanation regarding the settings,
please check the next page
HOME SCREEN
After initial setup, press EXIT to exit the initial setup, and
enter the HOME screen.
NAVIGATING THE ON-SCREEN MENU
This TV includes 2 separate version of an on-screen menu
- Firstly, please open the Live TV source. Please read the
chapter ‘’Input source’’ if it is not clear. Then press the
‘’HOME’’ button for the on-screen menu. Eventually press
the buttons and select a desired conguration.
- Secondly, browse the Home interface with buttons. Select
the menu icon and press OK. Eventually press buttons
and conrm the desired conguration option.
1. The HOME interface displays the ''Input'' icon in the upper
right corner. Press or buttons in order to select the
''Inputs'' icon. Please press OK in order to open all the
optional input sources. Then press buttons to select a
desired source. Eventually press the OK button in order to
conrm the input source.

Channels – Display the scan sub-menu
Channel installation modes.
Antenna – Set the signal type to antenna. When set to
Antenna, the TV can receive analog and digital (DVBT/T2)
broadcasting signals.
Cable – Set the signal type to cable. When set to Cable,
the TV can receive analog and QAM broadcasting signals.
Parental controls – Press button to select the option
then press OK button to enter the sub-menu.
Audio Channel – Press button to select the option
then press OK button to enter the sub-menu.
Open source licenses – Press button to select the
option then press OK button to enter the sub-menu.
Auto Channel Update
Channel installation mode – Select on-screen display
based on dierent
channel sources. You can select the signal type.
CHANNEL
Antenna
1.Menu->Settings->Channel->Channel Installation
Mode enter, choose Antenna.
2. Enter Menu->Settings->Channel->Channels.
3. 3. Channel Scan opens the ATV+DTV automatic
search platform interface of Antenna.
Update Scan: Re-automatically search for frequency
points outside.
Analog Manual Scan: Manual ATV search station.
After input the frequency point, you can select up or
down search station.
Single RF Scan: DTV manual search, left and right
after selecting RF Channel, directly OK search.
Cable
1. Menu->Settings->Channel->Channel Installation
Mode, select Cable.
2. Enter Menu->Settings->Channel->Channels.
1.Press the ‘’Network&Internet’’ icon.
2.Browse the desired conguration/Network.
3.Press the OK button to save and return to the previous
menu.
Network

Set date – Press button to select the option
then press OK button to enter the sub-menu.
Set time – Press button to select the option
then press OK button to enter the sub-menu.
Set time zone – Press button to select the option
then press OK button to enter the sub-menu.
Use 24-hour format – Press button to select the
option then press OK button to choose ON/OFF.
In this menu, you can read the information and
settings of TV.
1. Press button to select what you want set.
2. Press OK button to adjust.
3. After nishing your adjustment, Press BACK button
to return to the previous menu.
DATE&TIME
DEVICE PREFERENCES
ABOUT
Manually adjusting date & time settings will
automaticall change the Automatic date & time
to OFF.
NOTE
Automatic date & time – Press button to
select the option then press OK button to enter
the sub-menu.
(Optional: Use network-provided time, O)
TIMER
Power On Timer Type –Press button to select the
option then press OK button to choose ON/OFF/ONCE.
Power On Timer – Press button to select the
option then press OK button to enter the sub-menu.
Power O Timer Type – Press button to select
the option then press OK button to choose ON/OFF/ONCE.
Power O Timer – Press button to select the
option then press OK button to enter the sub-menu.
LANGUAGE
Language – Press button to select the option
then press OK button to enter the select language.
3. Enter Channel Scan, where Akado, Divan TV,
Online and Rostelecom (SPB) are the local operators,
and the default Scan Mode is Advance;Others have
Advance, Quick and Full Scan modes.
Single RF Scan: manual search station.

KEYBOARD
Current keyboard – Press button to select the
option then press OK button to enter the sub-menu.
Gboard Settings – Press button to select the
option then press OK button to enter the sub-menu.
Manage keyboards – Press button to select the
option then press OK button to enter the sub-menu.
INPUTS
POWER
Sleep Timer – Press button to select the option
then press OK button to enter the sub-menu.
(Optional: OFF, 10 minutes, 20 minutes, 30 minutes
40 minutes, 50 minutes, 60 minutes, 90 minutes,
120 minutes)
PICTURE
HDR
on
Picture OFF – Press button to select the option then
press OK button to choose ON/OFF.
Switch o timer – Press button to select the option
then press OK button to enter the sub-menu.
(Optional: OFF, 30 minutes, 60 minutes, 90 minutes,
120 minutes, 150 minutes, 180 minutes, 210 minutes,
240 minutes)
No Signal Auto Power O – Press button to select
the option then press OK button to enter the sub-menu.
(Options: 5, 10, 15, 30 or 60 minutes)
Picture Mode – Press button to select the option
button to enter the sub-menu. (Options: User, Standard,
Vivid, Sport, Movie, Game, Energy saving).
Backlight/Brightness/Contrast/Saturation/HUE/ Sharpness –
Press button to select the option. Press to decrease
the parameter. Press to increase the parameter.
Gamma – Press button to select the option then
press OK button to enter the sub-menu.
(Options: Dark, middle, Bright).
Color Temperature – Press button to select
the option then press OK button to enter the sub-menu.
Picture format – Press button to select
the option then press OK button to enter the sub-menu.
(Options: Automatic/Super zoom/4:3/Movie expand 14:9/
Movie expand 16:9/Wide screen/Full/Unscaled).
HDR – Press button to select the option then press
OK button to enter the sub-menu.
(Options: ON/OFF)
Advanced Video – Press button to select
the option then press OK button to enter the sub-menu.
Color Tuner – Press button to select
the option then press OK button to enter the sub-menu.
11 Point White Balance Correction – Press button
to select the option then press OK button to enter the
sub-menu.
Reset to Default – Resets all settings to the factory defaults.
Inputs – Press button to select the
option then press OK button to enter the sub-menu.
HDMI control – Press button to select the
option then press OK to choose ON/OFF.
Device auto power o – Press button to select the
option then press OK button to choose ON/OFF.
TV auto power on – Press button to select the
option then press OK button to choose ON/OFF
HDMI EDID Version – Displays EDID version.
CEC Device List – Press button to select the
option then press OK button to enter the sub-menu.