ANTZER TECH CO RIFA-M User manual

USER MANUAL
Version 2.1.0
June 22th, 2019
ANTZER TECH CO., LTD.
11F-1, No.475, Guangfu S. Rd., Xinyi Dist., Taipei City 11074,
Taiwan (R.O.C.)
Tel: [phone]
www.antzer-tech.com
RIFA-M Multifunctional
Vehicle Tracking Unit

© 2018 ANTZER TECH CO., LTD. 1
Important User Information
Liability
Every care has been taken in the preparation of this document. Please inform
ANTZER TECH CO., LTD. any inaccuracies or omissions. The data and
illustrations found in this document are not binding. We, ANTZER TECH CO.,
LTD. reserve the right to modify our products in line with our policy of continuous
product development. The information in this document is subject to change
without notice and therefore should not be considered as a binding description of
the range of functions (neither for future product versions). ANTZER TECH CO.,
LTD. assumes no responsibility for any errors that may appear in this document.
There are many applications of the described product. Those responsible for the use
of this device must ensure that all the necessary steps have been taken to verify that
the applications meet all performance and safety requirements including any
applicable laws, regulations, codes, and standards. ANTZER TECH CO., LTD. will
under no circumstances assume liability or responsibility for any problems that may
arise as a result from improper use or use that is not in accordance with the
documented features of this product.
The examples and illustrations in this document are included solely for
illustrative purposes.
Intellectual Property Rights
ANTZER TECH CO., LTD. has intellectual property rights relating to
technology embodied in the product described in this document. These intellectual
property rights may include patents and pending patent applications in Taiwan and
other countries.
Copyright © 2016 ANTZER TECH CO., LTD. All rights reserved.
Antzer Tech RIFA Series User Manual

© 2018 ANTZER TECH CO., LTD. 2
Table of Contents
1. Product Description........................................................................................... 3
1.1. Introduction ...................................................................................................... 3
1.2. Document History.............................................................................................. 3
1.3. Hardware Specification...................................................................................... 4
2. Hardware Feature.............................................................................................. 5
2.1. MicroFit Connector............................................................................................ 5
2.2. Micro-USB Connector ........................................................................................ 6
2.3. LED Indication and External Antenna Connector................................................ 7
2.4. Buzzer Operation............................................................................................... 7
2.5. SIM Card Slot ..................................................................................................... 8
2.6. Backup Battery .................................................................................................. 8
3. Configuration..................................................................................................... 9
3.1. USB Driver Installation....................................................................................... 9
3.2. Configuring RIFA-M............................................................................................ 9
3.3. BLE Function for Android App Application (Optional)....................................... 15
3.3.1 System Requirement.................................................................................... 15
3.3.2 APK File.................................................................................................... 15
3.3.3 Installation............................................................................................... 15
3.3.4 Connect Procedures................................................................................. 15
3.3.5 Bluetooth Disconnection Procedures ....................................................... 19
3.3.6 Known Issues and troubleshooting (depends on Android Version) ........... 20
4. Firmware Update............................................................................................. 20
5. Dimension Drawing ......................................................................................... 22
6.Reliability Specifications ....................................................................................... 23
6.1 Environmental ................................................................................................. 23
6.2 Certification and Compliance........................................................................... 23
7 Appendix A - RIFA-M Series Transmission Protocol .......................................... 24
8 Appendix B –AT command list of RIFA-M ........................................................ 27
9Appendix C – RIFA BLE Transmit Protocol Format (Optional) ............................ 35
10. Appendix D - Server information setting ......................................................... 37

© 2018 ANTZER TECH CO., LTD. 3
1. Product Description
1.1. Introduction
Antzer-Tech Automotive-Grade RIFA-M Multifunctional vehicle tracking
unit provides a compact, economic, easily installed solution for fleet
management. RIFA’s self-designed firmware not only supports OBDII & J1939
protocols, but integrates superior cellular modem, highly sensitive GPS,
accelerometer (G-sensor) in one end-to-end solution. With built-in antennas for
both GPS and Cellular modules, RIFA engineers a truly robust connectivity.
RIFA-M is combining with the most comprehensive and economical vehicle
diagnostics technology and multi-functional I/Os, which provides real-time
engine monitoring and GPS location. The engine diagnostic data is collected
through the vehicle's OBD-II/J1939 communication port and is transmitted via
cellular network to the back-end center. In this way, potential engine problems
can be identified earlier before the vehicle breaks down at an inopportune time.
Furthermore, you may configure other advanced driving behavior events such as
harsh braking, sudden acceleration, speeding, cornering, and much more in order
to reduce the risks of vehicle damage and drive down the costs of fuel. This user
manual is intended to guide you through the installation and configuration
process. Also, you can select different accessories such as TPMS (tire pressure
monitoring sensor), NFC card reader, temperature and humility sensor, and
emergency button which is compatible with RIFA-M.
1.2. Document History
Version
Date
Author
Description
1.3
22-Nov-18
Leopold Chen
First version of this document
2.1
22-Jun-19
Leopold Chen
Second version

© 2018 ANTZER TECH CO., LTD. 4
1.3. Hardware Specification
General
Vehicle Interface
20pin MicroFit Connector
Messages
12,000 Buffered Messages
Geofencing
Geofences Zones (Polygon, Rectangular or Circle Setting)
Configuration
AT command or configurator under Microsoft Windows
Vehicle Network
Protocol Support
ISO15765-4 On-Board Diagnostic, J1939 and Mobileye® Protocol
(reserved)
Cellular Network
Frequency Band
(WWAN Module
Selected)
GSM/GPRS: 850,900,1800,1900 Mhz
HSPA/UMTS : 800,850,900,1700,1900,2100 Mhz
LTE Cat 1 : Band 4, 13 or Band 3,7,20
LTE Cat M1/NB 1 : Band 2,3,4,5,8,12,13,20,28
LoRa1: US915,EU868,AS923
Data Protocol
TCP, UDP, MQTT(reserved) or LoRaWAN(reserved)
Wireless Network
Bluetooth
2.4GHz Low Energy Bluetooth Class 2
GPS
Chipset
Ublox Neo M8 Engine, 72Channels support GPS, Galileo,
GLONASS, BeiDou
Dead Reckoning
Optionally Support UDR, Tracking with GPS Signal Loss
Sensor
3-Axis G-sensor with Auto-Calibrating Function
LED Indicator
x2 LEDS (2 Colors each for GPS, Cellular Network, and System
Status)
SIM Card
Form Factor
Mini SIM 2FF (25 x 15 mm)
Comprehensive I/O
MicroFit Connector
Dual CAN Ports for OBDII, J1939 or Mobileye® Signal Input
x1 RS-485 and x1 RS-232
x2 Digital Input and x2 Digital Output (100mA)
x1 Analog Input (under 32V) and x1 1-wire Interface
x1 Ignition Input Detect
Audio
x1 Mic-in and x1 Headphone-out (resvered)
Configuration Port
Micro USB with 5V Power Input (without battery)
Power
Power Input Range
9~32V DC Power Input from Micro Fit Connector
Power Mode
Operating Mode, Sleep Mode, and Backup Battery Mode
Min. Power
Consumption
<4.5 mA @ 12V (Sleep mode), Support CAN Wakeup Function
Buzzer
Built-in Buzzer for System Status
Environment
Operating
Temperature
-30 to 70 °C (Without Battery); -20 to 70 °C (With Battery)

© 2018 ANTZER TECH CO., LTD. 5
Storage Temperature
-40 to 85 °C
Certificate and
Vibration
CE, FCC, RoHS and MIL-STD-810G 514.6
Humidity
10% to 90% R.H. (Non-Condensing) Compliant
Dimensions
86 x 56 x 28 mm
Battery
Lithium Ion Battery
Optionally support Built-in 3.7V 130mAh Battery
(standard for emergency service)
1.External antenna is needed
2. Hardware Feature
2.1. MicroFit Connector
For the standard configuration, Antzer-Tech RIFA-M can support ISO 15765-4, SAE J2284
and SAE J1939 on MicroFit by pin 2/12 and pin 3/13 with CAN High/Low signal. Also,
RIFA-M supports wide range power input from 9V to 32V by pin 1/11 and ignition input by
pin 4. Furthermore, RIFA-M provides 2xDI, 2xDO, 1xRS485, 1xRS232, 1x Analog in, 1x
one-wire, 1x buzzer out and 1xVDC(5V) out.The pin definition is as the below table.
RIFA-M

© 2018 ANTZER TECH CO., LTD. 6
2.2. Micro-USB Connector
There is a micro-USB port on the RIFA-M for configuration usage. Connecting it
with your PC or notebook USB port can power up RIFA-M for configurator.
Run the RIFA-M Configuration Tool or AT command to execute the settings on
RIFA-M.
Warning : RIFA-M is powered up by USB (0.8A@5V) , for this mode , RIFA-M is
only permitted for configuring. For real application , please connect power supply
via Micro-fit connector over 12V.

© 2018 ANTZER TECH CO., LTD. 7
2.3. LED Indication and External Antenna Connector
There is a LED indicator of RIFA-M to show the status of WWAN(cellular
network),GPS and System power.
LINK(LED1) Yellow Light: to show RIFA’s WWAN module works fine.
LINK(LED1) Green Light: to show RIFA’s GPS module works fine.
SYSTEM(LED2) Red Light: to show RIFA’s power-input works fine.
There are one external WWAN antenna connector nearby LINK LED(RP-
SMA Female ) and one external GPS antenna connector nearby SYSTEM LED
(RP-SMA Female ) equipped in RIFA-M
2.4. Buzzer Operation
There is a buzzer equipped on RIFA to indicate (1) System reboot (2) Waring
on unsafe driver behavior (3) Waring on driving to restricted area (Geofence) (4)
GPS signal detection.
Beep * 1 : Power / System On
Beep * 3 : WWAN Access Point Connection
Beep * 4 : GPS Satellite Connect
WWAN Antenna Connector
GPS Antenna Connector

© 2018 ANTZER TECH CO., LTD. 8
2.5. SIM Card Slot
User can insert the SIM card (MiniSIM,2FF) to RIFA’s SIM card slot showing
by below photo.
2.6. Backup Battery
The RIFA-M is optionally equipped a backup battery which allows RIFA-M keep
operating for about 5~8 min emergency service. and sending the alarm to central
management center at a power loss. However, you may not want to enable the battery
after testing. You can turn off the battery power by removing the jumper and turn the
battery power (for charge or discharge) by connecting the jumper.
Below photo shows the jumper’s location on RIFA

© 2018 ANTZER TECH CO., LTD. 9
3. Configuration
Antzer Tech supply a simplicity and clarity configuration tool or AT command which is
so user-friendly. RIFA collects the common setting by default that customer only need to
define the impactive setting.
3.1. USB Driver Installation
Following section 2.2. Checking the driver of USB cable is already installed on
your laptop or notebook PC which you want to use it to configure the RIFA. ( in
Windows 10 , the USB driver is auto detect and install)
3.2. Configuring RIFA-M
Checking the hardware set-up is finished by section2.2. And then executing the
“RIFA configure Tool” to configure RIFA.
First, you need to select the COM port correctly with your host device. And then
click “Connect” button to start your RIFA’s configuration.