Anybus AWB5011 User manual

Anybus®Managed Industrial L3 Switch
USER MANUAL
SCM-1202-151 1.1 en-US ENGLISH

Important User Information
Disclaimer
The information in this document is for informational purposes only. Please inform HMS Industrial Networks of any
inaccuracies or omissions found in this document. HMS Industrial Networks disclaims any responsibility or liability
for any errors that may appear in this document.
HMS Industrial Networks reserves the right to modify its products in line with its policy of continuous product
development. The information in this document shall therefore not be construed as a commitment on the part of
HMS Industrial Networks and is subject to change without notice. HMS Industrial Networks makes no commitment
to update or keep current the information in this document.
The data, examples and illustrations found in this document are included for illustrative purposes and are only
intended to help improve understanding of the functionality and handling of the product. In view of the wide range
of possible applications of the product, and because of the many variables and requirements associated with any
particular implementation, HMS Industrial Networks cannot assume responsibility or liability for actual use based on
the data, examples or illustrations included in this document nor for any damages incurred during installation of the
product. Those responsible for the use of the product must acquire sufficient knowledge in order to ensure that the
product is used correctly in their specific application and that the application meets all performance and safety
requirements including any applicable laws, regulations, codes and standards. Further, HMS Industrial Networks will
under no circumstances assume liability or responsibility for any problems that may arise as a result from the use of
undocumented features or functional side effects found outside the documented scope of the product. The effects
caused by any direct or indirect use of such aspects of the product are undefined and may include e.g. compatibility
issues and stability issues.
Anybus®Managed Industrial L3 Switch User Manual SCM-1202-151 1.1 en-US

Anybus®Managed Industrial L3 Switch User Manual SCM-1202-151 1.1 en-US
Table of Contents Page
1 Preface ................................................................................................................................. 5
1.1 About This Document .......................................................................................................5
1.2 Document Conventions.....................................................................................................5
1.3 Trademarks.....................................................................................................................5
2 Safety ................................................................................................................................... 6
2.1 Intended Use...................................................................................................................6
2.2 General Safety.................................................................................................................6
3 Preparation.......................................................................................................................... 7
3.1 Support and Resources .....................................................................................................7
4 Installation........................................................................................................................... 8
4.1 DIN Rail Mounting............................................................................................................8
4.2 Connecting Ground Screw .................................................................................................9
4.3 Terminal Block Connector................................................................................................ 10
4.4 Installing Terminal Block.................................................................................................. 10
4.5 Connecting Digital Output Wires....................................................................................... 11
4.6 Connecting Digital Input Wires ......................................................................................... 12
4.7 Connecting Power Wires ................................................................................................. 13
4.8 Connecting to Ethernet Network ...................................................................................... 14
4.9 Connecting to Fiber Network ........................................................................................... 14

Anybus®Managed Industrial L3 Switch User Manual SCM-1202-151 1.1 en-US
5 Configuration..................................................................................................................... 15
5.1 Before You Begin Configuration........................................................................................ 15
5.2 Accessing the Web Management Interface ......................................................................... 15
5.3 Web Interface Overview.................................................................................................. 16
5.4 System Information ........................................................................................................ 17
5.5 User Account................................................................................................................. 18
5.6 IP Settings..................................................................................................................... 21
5.7 Date and Time............................................................................................................... 24
5.8 DHCP Server.................................................................................................................. 26
5.9 Ethernet Port ................................................................................................................ 35
5.10 Redundancy.................................................................................................................. 46
5.11 VLAN ........................................................................................................................... 58
5.12 Quality of Service (QoS) .................................................................................................. 65
5.13 Multicast ...................................................................................................................... 69
5.14 Routing ........................................................................................................................ 72
5.15 SNMP .......................................................................................................................... 84
5.16 Security........................................................................................................................ 87
5.17 Warning ....................................................................................................................... 96
5.18 Diagnostics ................................................................................................................. 101
6 Verify Operation.............................................................................................................. 106
6.1 System LED Indicators................................................................................................... 106
6.2 Ethernet LED Indicators................................................................................................. 106
6.3 SFP Port LED Indicators ................................................................................................. 107
7 Maintenance and Troubleshooting ................................................................................ 108
7.1 USB Port..................................................................................................................... 108
7.2 Backup and Restore...................................................................................................... 108
7.3 Firmware Upgrade ....................................................................................................... 110
7.4 Reset To Default .......................................................................................................... 111
7.5 Factory Reset Button .................................................................................................... 112
8 Technical Data ................................................................................................................. 113
8.1 Technical Specifications................................................................................................. 113
A About DHCP Option 82 ................................................................................................... 115
B About Port Trunk............................................................................................................. 116
B.1 Port Trunk Concept ...................................................................................................... 116

Anybus®Managed Industrial L3 Switch User Manual SCM-1202-151 1.1 en-US
C About Connectivity Fault Management (CFM) .............................................................. 117
D About Redundancy.......................................................................................................... 118
D.1 Spanning Tree Protocol (STP) ......................................................................................... 118
D.2 Rapid Spanning Tree Protocol (RSTP) ............................................................................... 118
D.3 Multiple Spanning Tree Protocol (MSTP) .......................................................................... 118
E About Ethernet Ring Protection Switching (ERPS) ........................................................ 120
F About Virtual Local Area Network (VLAN)..................................................................... 121
G About Open Shortest Path First (OSPF).......................................................................... 122
H About Simple Network Management Protocol (SNMP)................................................ 123

This page intentionally left blank

Preface 5 (124)
1 Preface
1.1 About This Document
This manual describes the installation and configuration of Anybus Managed Industrial L3 Switch.
For additional documentation and software downloads, FAQs, troubleshooting guides and
technical support, please visit www.anybus.com/support.
1.2 Document Conventions
Numbered lists indicate tasks that should be carried out in sequence:
1. First do this
2. Then do this
Bulleted lists are used for:
• Tasks that can be carried out in any order
• Itemized information
►An action
→ and a result
User interaction elements (buttons etc.) are indicated with bold text.
Program code and script examples
Cross-reference within this document: Document Conventions, p. 5
External link (URL): www.hms-networks.com
WARNING
Instruction that must be followed to avoid a risk of death or serious injury.
Caution
Instruction that must be followed to avoid a risk of personal injury.
Instruction that must be followed to avoid a risk of reduced functionality and/or damage
to the equipment, or to avoid a network security risk.
Additional information which may facilitate installation and/or operation.
1.3 Trademarks
Anybus®is a registered trademark of HMS Industrial Networks. All other trademarks mentioned
in this document are the property of their respective holders.
Anybus®Managed Industrial L3 Switch User Manual SCM-1202-151 1.1 en-US

Safety 6 (124)
2 Safety
2.1 Intended Use
The intended use of this equipment is as a communication interface and gateway. The
equipment receives and transmits data on various physical levels and connection types.
If this equipment is used in a manner not specified by the manufacturer, the protection provided
by the equipment may be impaired.
2.2 General Safety
Caution
Ensure that the power supply is turned off before connecting it to the equipment.
Connecting power with reverse polarity or using the wrong type of power supply may
damage the equipment. Make sure that the power supply is connected correctly and of
the recommended type.
Anybus®Managed Industrial L3 Switch User Manual SCM-1202-151 1.1 en-US

Preparation 7 (124)
3 Preparation
3.1 Support and Resources
For additional documentation and software downloads, FAQs, troubleshooting guides and
technical support, please visit www.anybus.com/support.
Have the product article number available, to search for the specific product page. You find the product
article number on the product cover.
Anybus®Managed Industrial L3 Switch User Manual SCM-1202-151 1.1 en-US

Installation 8 (124)
4 Installation
4.1 DIN Rail Mounting
Mount the switch on a DIN rail in accordance with the EN 50022 standard.
Procedure
Mount the switch on a DIN rail:
1. Insert the upper end of the DIN rail clip into the DIN rail.
2. Push the bottom of the DIN rail clip into the DIN rail.
Anybus®Managed Industrial L3 Switch User Manual SCM-1202-151 1.1 en-US

Installation 9 (124)
4.2 Connecting Ground Screw
To avoid system damage, the equipment should be connected to ground.
Procedure
1. Establish a direct connection between the ground screw and the grounding surface prior to
connecting devices.
Anybus®Managed Industrial L3 Switch User Manual SCM-1202-151 1.1 en-US

Installation 10 (124)
4.3 Terminal Block Connector
Contact Number Description
1DO, Digital Output
2
3DI, Digital Input –
4DI, Digital Input +
5 P2, Power Input 2 –
6 P2, Power Input 2 +
7 P1, Power Input 1 –
8 P1, Power Input 1 +
4.4 Installing Terminal Block
Procedure
1. Attach the terminal block to the contact on the switch.
2. Fasten the terminal block with the 2 screws included.
Anybus®Managed Industrial L3 Switch User Manual SCM-1202-151 1.1 en-US

Installation 11 (124)
4.5 Connecting Digital Output Wires
Before You Begin
The relay output is used to detect user-configured events.
When a user-configured event is triggered, the two wires attached to the DO, fault contacts,
form a close circuit.
The fault circuit remains opened until a user-configured event occur.
Procedure
Connect the Digital Output (DO):
1. Insert the wires into the 2 pin DO contact on the 8 pin terminal block.
2. Tighten the wire-clamp screws.
Anybus®Managed Industrial L3 Switch User Manual SCM-1202-151 1.1 en-US

Installation 12 (124)
4.6 Connecting Digital Input Wires
Procedure
Connect the Digital Input (DI):
1. Insert the wires into the 2 pin DI - and DI + contact on the 8 pin terminal block.
2. Tighten the wire-clamp screws.
Anybus®Managed Industrial L3 Switch User Manual SCM-1202-151 1.1 en-US

Installation 13 (124)
4.7 Connecting Power Wires
Caution
Ensure that the power supply is turned off before connecting it to the equipment.
Use a power supply of 24 VDC (10-60 VDC) to power the switch.
Max power consumption: 16.08 W.
The relay contact supports 0.5 A current, 24 VDC.
Procedure
1. Connecting to main power supply P1: Insert the positive and negative wires into the P1+
and P1- contact on the 8 pin terminal block.
2. Connecting to redundant power supply P2: Insert the positive and negative wires into the
P2+ and P2- contact on the 8 pin terminal block.
3. Tighten the wire-clamp screws.
4. Connect the power wires to a DC switching type power supply.
Anybus®Managed Industrial L3 Switch User Manual SCM-1202-151 1.1 en-US

Installation 14 (124)
4.8 Connecting to Ethernet Network
Optional
Connect the switch to an Ethernet network.
4.9 Connecting to Fiber Network
Optional
Connect the switch to a network via the SFP port.
Anybus®Managed Industrial L3 Switch User Manual SCM-1202-151 1.1 en-US

Configuration 15 (124)
5 Configuration
5.1 Before You Begin Configuration
The switch is configured through web management or console management.
The switch can also be configured through Telnet management or SSH management.
The switch default IP address is http://192.168.10.1/.
The default switch login user name is admin and the password is admin.
5.2 Accessing the Web Management Interface
Prepare for configuring the switch settings via the web management interface.
Before You Begin
►Connect the switch to your computer.
►Connect the switch to power.
►To link your computer with the switch, make sure that the IP address of the computer is
located in the same subnet as the switch default IP address.
Procedure
Access the web management interface:
1. In your browser, type http://IP address and press Enter.
→ The web-based management interface login screen appears.
2. In the login screen, enter user name and password.
3. Click OK.
→ The web-based management interface welcome page appears.
To Do Next
►Configure the switch.
Anybus®Managed Industrial L3 Switch User Manual SCM-1202-151 1.1 en-US

Configuration 16 (124)
5.3 Web Interface Overview
Fig. 1 Web Interface Overview
5.3.1 To Save Settings
Unsaved settings will be lost when the switch is powered off or restarted.
►To apply changes made on a configuration page/tab, click Submit at the bottom of the page.
►To cancel the changes, click Cancel.
Some pages have additional buttons that are described in the respective sections in this
manual.
►To save changed settings permanently, click Save in the configuration page top menu.
The recent changes will otherwise be discarded if the switch is rebooted.
5.3.2 To Logout From the Web Interface
To manually logout from the system:
1. In the web interface top menu, click Logout.
2. To confirm, click Yes.
Anybus®Managed Industrial L3 Switch User Manual SCM-1202-151 1.1 en-US

Configuration 17 (124)
5.3.3 To Reboot the Switch
Unsaved settings will be lost when the switch reboot.
Some changes to the settings require the user to reboot the switch.
To manually reboot the switch:
1. In the web interface top menu, click Reboot.
2. To confirm, click Yes.
→ The switch will reboot immediately.
5.4 System Information
The Information page shows the basic switch information.
Fig. 2 Switch information
Configure the switch information:
System Name Name of the unit that will be shown on the
network
Default: switch
System Location Specify the physical location of the switch.
Default: blank
Software Contact Specify a contact person.
Enter name, mail address or other information.
Default: blank
OID Switch Object ID.
System Description Product name
Software Version Latest installed firmware version.
MAC Address MAC address of the Ethernet network interface
To apply the settings, click Submit.
Anybus®Managed Industrial L3 Switch User Manual SCM-1202-151 1.1 en-US

Configuration 18 (124)
5.5 User Account
The User Account page consists of two interfaces, Local User and RADIUS Interface.
The default authority allows the user to configure all configuration parameters.
For security consideration, please change the password after first login to the web
interface.
The default switch login user name is admin and the password is admin.
Anybus®Managed Industrial L3 Switch User Manual SCM-1202-151 1.1 en-US