Aoycocr Smart Switch User manual

Quick Start
01 | PRODUCT OVERVIEW
      
02 | INDICATOR LIGHT STATUS
03 | WARNINGS
Turn off the power at the circuit breaker and test that power is off before
wiring.
Check supported maximum wattage rating: 1200W.
Replace single pole switch only; NO NOT compatible with 3-way switch.
04 | INSTALLATION
Note
Make Sure that the power at the circuit breaker is off before wiring.
Light Color Light Status Switch Status
Red Power On
Blue OFF
Green Blink quickly Ready for default configuration mode(Easy
Mode)
Blink slowly Ready for AP mode Configuration

Neutral Wire is required. Confirm the wall box contains a Neutral
Wire(typically white). if the wall box doesn't have a Neutral Wire, please try
another location in your home or call a professional electrician to install the
switch.
The Wire colors indicated in this manual are the usual colors and may differ
in some homes.
Ensure the wire conductors are securely fastened to each wire.
Ensure the Wi-Fi signal is strong before wiring.
If you don't have any wiring experience, please call a professional electrician .
Use the non-contact voltage tester to test the power. Ensure the switch is off before
wiring
Turn on the power at the circuit breaker and use an electrical tester to check which
wire is line wire; the tester will flash and chirp when it comes close to a line wire; Turn
off the power at the circuit breaker and use the electrical tester to test if the power
is off, and then pull the exist switch out, label the line wire and other wires; discount
the wires from the existing switch with pliers(Make sure the existing switch box has a
neutral wire*. *Neutral wire is typically white)

Follow the wiring diagram to connect the switch wires to the wires in the wall box
with the wire conductors
Mount the switch with the provided screws and snap the wall plate on it
Some warm t ips for you:
1. If the indicator doesn't flashing when you power on the switch for the first
connection, please hold a 25 seconds press on the switch and see if it st art s

flashing;
2. If the smart swit ch can't be connect ed t o WiFi, please long press ON/OFF button
for 25 seconds to reset the switch or change t he easy mode to AP mode which is
more compatible;
3. T he smart switch only works with 2.4 GHz networks. If your router broadcast s
bot h 2.4 and 5GHz, please selected t he 2.4GHz network wit h t he app. If t he
connection st ill failed, we recommend you call your ISP and had them completely
shut off the 5 GHz network on t he router; You are free to change the network to 5
GHz again aft er connecting;
4. Please try to make your smart outlet and router as close as possible when the
first connection, you can change t he place aft er connecting successfully.
05 | CONFIGURE THE APP TO THE SWITCH
Preparation:
Download Smart Life APP
Ensure the smart light switch has connected with electricity.
Ensure your phone has connected to the Wi-Fi router and is able to connect
the internet.
Note: This smart light switch only supports the 2.4Ghz network. if you have
connected 5G network, please disconnect the 5G network and connect with a
2.4G network firstly.

Easy Mode
Tap the icon"+" on the top right corner to add device; choose "switch(Wi-
Fi)".
Confirm indicator rapidly blink. if not, press and hold the manual switch for
25 seconds until the LED indicator light blinks blue quickly.

Tap "Confirm indicator rapidly blink".

Enter Wi-Fi Password; wait for completing the connection.(Choose the 2.4G
network and enter right password)

Device has added successfully.

AP Mode
Note:
1. If you can't configure successfully with the Easy Mode(default configure mode),
please try to connect with AP Mode.
2. Make sure indicator light is blink blue slowly.
Tap the icon"+" on the top right corner to add device; choose "Switch( Wi-Fi
)".

Tap "AP Mode" on the top right corner.

 Press and hold the manual switch for 25 seconds, until the indicator light
blink blue slowly(once per 3 seconds).

Tap "Confirm indicator slowly blink".

Enter Wi-Fi Password.

Open WLAN setting, connect with "SmartLife-xxxx".

Back to the app and continue to add the device and wait for completing the
connection.

06 | RESET & RESTART
Press and hold the button for 25 seconds until the indicator light blinks rapidly
to reset if the switch isn't working - Reset one time (press and hold) to reach
Easy Mode (quickly blinking blue) - Reset again (press and hold) to reach AP
Mode (Slowly blinking blue)
07 | TROUBLESHOOTING GUIDE

8 | SUPPORT
Aoycocr Smart Switch with 90 days unconditional full money-back guarantee, 2-year
warranty, and lifetime support
Tech Support：[e-mail]
Facebook Page: htt ps://www.facebook.com/Aoycocr