ANYCAM IR-2IPR03 User manual

5/
3/2-mega Pixels Network camera
Version:
V1.0
Doc. No.:
1071018001
oPeratioN meNu
ir-2iPr03 2mP Face recogNitioN camera

2
Safety information
This symbol indicates that dangerous voltage consist a risk of electric shock is present
within this unit. Megapixels
This exclamation point symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the
appliance.
WARNING
To prevent damage that may result in fire or electric shock hazard, do not expose this
appliance to rain or moisture.
To prevent injury, this apparatus must be securely attached to the floor / wall in accordance
with the installation instructions.
WARNING
1. Be sure to use only the standard adapter that is specified in the specification sheet using any
other adapter could cause fire, electric shock, or damage to the product.
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire,
electric shock, or damage to the product.
3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause
the abnormal heat generation or fire.
4. Securely plug the power cord into the power receptacle, insecure connection may cause fire.
5. When installing the camera, fasten it securely and firmly. The fall of camera may cause
personal injury.
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers

3
filled with water on top of the camera. Doing so may cause personal injury due to fire,
electric shock, or falling objects.
7. If any unusual smells or smoke come from the unit, stop using the product. In such case,
immediately disconnect the power source and contact the service center. Continued use in
such a condition may cause fire or electric shock.
8. If this product fails to operate normally, contact the nearest service center and never
disassemble or modify this product in any way. (I-View is not liable for problems caused by
unauthorized modifications or attempted repair.)
9. When cleaning, do not spray water directly onto parts of the product. Doing so may cause
fire or electric shock.
CAUTION
Do not drop objects on the product or apply strong shock to it. Keep away from a location
subject to excessive vibration or magnetic interference.
Do not install in a location subject to high temperature (over 50°C), low temperature (below
-10°C), or high humidity. Doing so may cause fire or electric shock.
If you want to relocate the already installed product, be sure to turn off the power and then
move or reinstall it.
Remove the power plug from the outlet when then there is a lightning. Neglecting to do so
may cause fire or damage to the product.
Keep out of direct sunlight and heat radiation sources. It may cause fire.
Install it in a place with good ventilation.
Avoid aiming the camera directly towards extremely bright objects such as sun, as this may
damage the CCD image sensor.
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
The Mains plug is used as a disconnect device and shall stay readily operable at any time.
Do not expose the camera to radioactivity. Radioactivity exposure may damage the CCD.

4
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
Do not install near any heat sources such as radiators, heat registers, or other apparatus
(Including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a
third grounding prong. The wide blade or the third prong is provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus.
Unplug this apparatus when a card is used. Use caution when moving the cart/ apparatus
combination to avoid injury from tip-over.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain
or moisture, does not operate normally, or has been dropped.
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids,
such as vases, shall be placed on the apparatus.

5
SAFETY INFORMATION
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following
conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received including interference that may cause
undesired operation.
CAUTION
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
This marking on the product, accessories or literature indicates that the product and its
electronic accessories should not be disposed of with other household waste at the end of their
working life. To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate these items from other types of waste and recycle them
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their
local government office, for details of where and how they can take these items for
environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product and its electronic
accessories should not be mixed with other commercial wastes for disposal.
This equipment has bee
n tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of FCC Rules. These limits are designed to provide
reasonable
protection against harmful interference when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful
interference in which case the user will be required to correct the interference at his own
e
xpense.

6
About This Guide
Conventions used in this guide
To make sure that you perform certain tasks properly, take note of the following symbols to use
throughout this manual.
WARNING: Information to prevent injury to yourself when trying to complete a task.
CAUTION: Information to prevent damage to the components when trying to complete a
task.
IMPORTANT: Information that you must follow to complete a task.
NOTE: Tips and additional information to aid in completing a task.
Trademark
I-View, e-Witness, @-Witness Pro, u-Witness XP, x-Witness, FreeView Pro,AnyCam, P D AVi r w
and MobileView are registered trademarks of I-View Communication Inc.
Microsoft, Windows 95, 98, ME, Windows2000, XP,Vista,7 and 8 are registered trademarks of
Microsoft Corporation. All other trademarks are the property of their respective holders.
Customer Support
If technical problems arise with the use of our products in which you and your vendor cannot
resolve, please try the following: If you have an Internet connection, visit the I-View website
http://www.i-view.com.tw (Taiwan) for any software or product updates, or email to
[e-mail] (Taiwan) or Tel: [phone] Fax: [phone] (Taiwan). We
are dedicated to providing the highest quality support. E-mailing our tech support will give you
the chance to document each of the above items in a very clear and concise manner and will give
our support team a chance to document any problems and respond with thoroughly researched
answers.

7
Table of Contents
Chapter 1. Introduction ---------------------------------------------------------------------------------------- 8
1-1. Highlights of your new Network IP Camera ------------------------------------------------8
1-2. Packaging Contents --------------------------------------------------------------------------- 14
1-3.Product Dimension----------------------------------------------------------------------------- 14
Chapter 2. Camera Installation------------------------------------------------------------------------------ 17
2-1. Wall Mount installation----------------------------------------------------------------------- 17
Chapter 3. Running IP Camera by Witness Pro NVR software ------------------------------------- 18
3-1. Network Deployment------------------------------------------------------------------------- 18
3-2. Install Witness Pro NVR software ---------------------------------------------------------- 19
3-3. Setting IP camera for Witness Pro NVR software---------------------------------------- 21
Chapter 4. Accessing IE, Chrome, Safari and Firefox Browser -------------------------------------- 27
4-1. Install Plug-in on IE, Chrome, Safari and Firefox Browser | --------------------------- 28
4-2. Using RTSP Players--------------------------------------------------------------------------- 29
4-3. The Function Description of Live Window ----------------------------------------------- 30
4-4. The Function Description of Setup Window---------------------------------------------- 33
4-5. The Function Description of File Window ------------------------------------------------ 71
4-6. The Function Description of Log Window------------------------------------------------ 73
4-7. How to Setup the Database of Face Recognition? --------------------------------------- 74
4-8. How to run the Face Recognition on Browser?------------------------------------------- 77
Chapter 5. Troubleshooting ---------------------------------------------------------------------------------- 78

8
Chapter 1. Introduction
1-1.Highlights of your new Network IP Camera
Congratulates on purchasing this 2 Mega pixels Face recognition network IP Bullet Camera! This
IP Camera provides 2-Mega pixels high-resolution video quality, with its advanced megapixel lens;
you can view remote images in more detail than conventional close-circuit cameras.
Other highlights of this network IP Camera include:
Autonomous depth learning core algorithm of Face recognition.
Capture accuracy ≥ 99%, which supports the function of image quality score filtering face and
removing duplication.
Onvif compliant and RTSP protocol support.
H.265 compression saves bandwidth and storage size.
Built-in 802.3af compliant PoE.
Support multi IVA (Intelligent Video Analysis) function.
Up to 30 fps @2MP video resolution.
Auto alarm when SD card failed, Network failed, IP address conflict, Illegal access.
Support export/import/restore system configuration for backup purpose.
Adjustable auto reboot schedule by day, weekly.
Removable IR-cut filter supports threshold adjustable for Day & Night used.
Quick Zoom® to simple the Zoom and Focus adjustment remotely.
Smart IR Illuminators adjust the IR LED light across the entire area to get a well illuminated
image, effective up to 30 meters.
Vandal-proof IK10-rated, IP 66 Weather-proof rated Housing.
True WDR Enhancement for Unparalleled Visibility in Extremely Bright and Dark
Environments.
H.265/H.264 /MJPEG multiple simultaneous streams.
On-camera motion detection and privacy mask.
Anti-cut cable and junction box design for Protected Installation.
Pixel Counter and FPS display on the video for image clarity measurement to get the optimum
video quality and file size.
Virtual ePTZ for efficiency surveillance.

9
ROI (Region of Interest) encoding is used to enhance the quality of images which are specified
in advance.
Wide operation temperature (-20°C ~ 55°C) rage.

10
IR-2MIPR03 Series
System
Platform: 32-Bits image process DSP ; 512MB Flash; 1024MB DDR II RAM and Linux O.S.
Image Device
1/2" 2MP Sony Starlight progressive CMOS sensor. .
Video Setting
Compression: Video:16KM ~ 32M bits/sec (CBR/VBR configurable) H.265MP/H.264
HP/MP/BP, M-JPEG; Audio: G. 7 11 μ-low/ Codec (8K sample rate)
Resolution:Main Streaming:1920×1080, 1280×720, D1, 640*480, 352 x 288.
Sub streaming: 1280×720,D1 (720*576) ¸640x480, 640x360, and 350×288.
Third Streaming:1920×1080, 1280×720, D1, 640*480, 352 x 288.
Frame Rate: 2MP: 30 fps @ H.265/H.264/M-JPEG Mode; Frame rate can be adjustable by
user.
Streaming: Multi-Stream H.265MP/H.264 Base/Main/High Profile and Motion JPEG video
streaming
Control: Brightness, Contrast, Saturation, Sharpness, Hue, Exposure, Motion detection,
Mirror, Corridor mode, Shutter, Privacy mask, Flicker less, 3D Noise reduction, Defog, IRIS,
AES, Gamma, AWB, AGC, BLC, WDR, ROI, Audio gain, Alarm in/out. IVS trigger
recording by scheduling, Network Failed, IP address Conflict, Illegal Access, HDD (SD) error,
HDD Full, Alarm triggered, Frame/Bit rate display, Export/Import configuration, Reboot,
Restore..
Color: Color: 0.1 Lux /F1.2; B/W: 0.05/F1.2 Lux, 0 Lux IR LED on.
WDR: 100dB True WDR; Off/DWDR/TWDR/Off 4 modes.
Shutter: Slow shutter Auto / Fixed: 1/1s~1/100,000s
S/N Ratio: More than 50dB
Overlay: Text / Time Stamp; support more than OSD 80 characters,
Front size: position & Color adjustable by user.
Configure Import/Export parameters, Restore, Default setup
Audio Setting

11
G. 7 1 1 μ| G. 7 1 1 A, G.726| ADPCM audio encoding and decoding;
2-way audio; External Microphone input (Line in/Mic in); Speaker output.
2Vp-p audio input and audio output with 600Ωimpedance.
IVA Functions (Optional)
Object Counting, Unattended /Missing Object, Loitering, Tripwire Detection. Smart Motion
detection, Color Cast, Lose Focus, Image Expose, Image Dark, Video Loss, Video Occlusion ,
Network Failed, IP address Conflict, Illegal Access, Object Detection
Network
Protocol: IP4, IP6, HTTP, HTTPS, SSL, TCP, ICMP, IGMP, RTSP, RTP, RTCP, RTMP,
UDP, SNTP, SMTP, FTP, DHCP, DNS, DDNS, NTP, PPPoE, uPnP, Multicast.
Interface: RJ-45; 10BASE-T/100 BASE-TX.
Compatible: Onvif compliant
I VA
Face Recognition, Face Detect, Human Detect, Retrograde Detect, Density
Detect, Object Counting, Unattended, Object Detection, Missing, Object
Detection, Loitering, Detection, Tripwire Detection,Motion Detection, Color
Cast Detection, Lose Focus Detection, Image Expose Detection, Video Loss
Detection, Video Tamper Detect.
Management
Time: Manual Time Setting; Time Server, NTP support and Real Time Clock.
Event Trigger: Events triggered by IVA, the sensor with the configured schedule.
Event notification: Notification via Pop up video, move PTZ camera preset, send email and
trigger alarm output.
Update:Online Firmware update.
Browser
Internet Explorer 7.0 and above; Chrome, Safari, Firefox with Quick time Plug-In.
Video Setting
Compress:H.265/MP, H.264 HP/MP/BL, M-JPEG compression.
Frame Rate: 25fps @4MP, 30fps for all resolution; Frame rate and bit rate adjustable.

12
Bit Rate: 16K–8M Bits/sec. CBR/VBR mode.
Configure: Import/Export parameters, Restore, Default setup
Resolution:
Streaming 1: 1920 x1080P, 1280 x720, 720x576, 640x480, 352x288.
Streaming 2: 1280 x720, 720x576, 640x480, and 352x288.
Streaming 3: 1920 x1080P, 1280 x720, 720x576, 640x480, 352x288.
Control: Brightness, Contrast, Saturation, Sharpness, Hue, Exposure, Motion detection,
Mirror, Corridor mode, Shutter, Privacy mask, Flicker less, 3D Noise reduction, Defog, IRIS,
AES, Gamma, AWB, AGC, BLC, HLC, WDR, ROI, ePTZ, Audio gain, Alarm in/out, Slow
shutter, IVS trigger, Network Failed detect, SD card filed detect, Gamma, Power Frequency, IP
address Conflict, Illegal Access, Alarm triggered, Frame/Bit rate display.
Shutter: Slow shutter, Auto / Fixed: 1/1s~1/100,000s
WDR:≥ 120 dB; True WDR/DWDR/OFF Mode.
Illumination: Color: 0.01 Lux /F1.2; B/W: 0.005/F1.2 Lux, 0 Lux IR LED on.
White Balance: Auto, Customized, Pre-define modes.
Overlay:Text / Time Stamp; support more than OSD 80 characters, Front type, Front size,
position & Color adjustable by user.
Image Display Mode: Full, 4:3, 16:9, Original image.
Security
Password Protection, User access log,Multi-level user access with password protection.
I/O Port
DC power in, RJ-45, Audio in x1; Audio out x1, SD Card,Alarm in x2, Alarm out,
Reset.
Lens & IR LED
Lens: Vari Focal: f= 2.7-12mm/F1.4; 6-22mm/F1.4; 5-50mm/F1.4
Motorized: f= 2.8-12mm/F1.4 ; 2.8-12mm/F1.4; 5-50mm/F1.4
P-IRIS or DC-IRIS (Optional).
IR Cut: Built-in removable IR-cut filter for day & night function
IR Illuminators: 3 pieces VCSEL IR Illuminators effective up to 30 meters.

13
IR LED Controller: Support Smart Auto/Off/Manual IR LED control.
Surge Protector
Power: 2KV @ 1.2/50μS Common mode.
Signal: 6KV@ 102/700μS Differential mode.
Storage
IVA trigger, Alarm trigger, Network failed, Backup device configuration to SD card, HDD and
FTP, Up to128G SD card storage capability.
Housing
Aluminum housing with IP 66 Waterproof & IK10 Vandal resistant and 3-Axis bracket design.
Dimension/Weight
Ø 93 mm x 95.5 mm x 263 mm / 0.9 Kg (Including bracket).
Operation
Power: Maximum 3 W & 8W(IR LED On); PoE IEEE 802.3af Class 3; DC12V
Temperature: Temperature -20°C ~ 55°C; Humidity 20% ~ 80% RH.
Certificated
CE, FCC, RoHS, IP66.

14
1-2.Packaging Contents
Check the contents of your new Network IP Camera when you unpack the package. If any item is
missing, please contact your dealer of purchase for help. The package includes items as below:
following items: Network IP Camera x 1ea
Bundle NVR & CMS software CD x 1ea
User manual x 1ea
Power jack to terminal block converter x 1ea
Screw driver x 1ea
Mount panel x 1 ea
Accessory package x 1 set
1-3.Product Dimension
Anchor 7x27 * 3 ea
Screw 4 x27 Tp1 Bnd Sus *3 ea
Hexagon wrench 3.0mm L type * 1 ea
Hole
mount sticker * 1ea

15
Product Parts Description
Front side items description:
1. Sunshield cover: It protects the camera from the direct sunlight.
2. IR LED: These infrared LED’s are controlled by the illumination sensor.
3. Illumination Sensor: Detects incoming light to control the IR LED.
4. Mount panel: Mount the camera and wall/ceiling.
5. SD card slot: Micro SD card slot allow plugging up to 128 G or higher SD card. (Option)
6. Video out: 2 pin connector for the video out.
7. Reset button: Press 5-10 seconds for hardware reset the setting parameters to default.
8. Network port: Plug the RJ-45 LAN cable. This port support water proof tube and comes with
the POE+ power source.
9. Audio output: Plug Speaker (Request audio amplify) for audio output. (White RCA port).
Sunshield cover
Fix hole
Focus screw
Zoom screw
Adjust lens window
IR LED
Mount panel
Lens
Top cover
IR Sensor
Fix Screw
SD Card slot window
Video out
Reset button

16
10. Audio input: Plug in Microphone for audio input (Red RCA port).
11. Alarm in #1: Connect to the sensor input (Dry contact). Alarm in - (Pin 1); Alarm in + (Pin 2),
Ground (Pin 3 &4)
12.Alarm out/RS-485:Alarm out (Pin3 - & Pin4 -) connects to the trigger device such as light.
RS485 for the PTZ controller (Pin1 A & Pin2 B).
13.Video out:Composite video single output. (Yellow BNC port)
14.Power cable: Connect to DC12V power adapter when use none POE Hub. (Red DC jack)
15.Reset: Press 20 Seconds the reset button and the camera parameters will become to default.

17
Chapter 2. Camera Installation
2-1.Wall Mount installation
Wall Mount installation
Fix the camera
This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the
external cable is not. You are recommended to install this product below the edge of eaves to prevent
the cable from being externally exposed.
1) Paste the hole mount sticker on the position that you want to install.
2) Use the mount hole sticker to make a hole of 30mm in diameter for passing cable, and drill
another four holes on the wall to fix bracket mount.
3) Insert the anchors to fix the screws with the Mount panel.
Adjust camera angle from bracket mount (Please refer the photo as below)
1) Use the Hexagon wrench to loosen the bolt and to rotate the bracket to suitable position.
2) Adjust horizontal,vertical or rotate camera body angle of the camera.
3) Use the Hexagon wrench to tighten a bolt after adjusting the camera.

18
Chapter 3. Running IP Camera by Witness Pro NVR software
3-1. Network Deployment
General Connection (without PoE)
1. Connect RJ45 Ethernet cable to a switch. Use a Category 5 Cross Cable when your network
camera is directly connected to PC.
2. Connect the power cable from the Network Camera to a power outlet.
3. If you have external devices such as sensors and alarms, make the connection from the general
I/O terminal block
Power over Ethernet (PoE)
The Network Camera is PoE-compliant, allowing transmission of power and data via a single
Ethernet cable. Follow the above illustration to connect the Network Camera to a PoE-enabled switch
via Ethernet cable.

19
Fig. 1-3-1.2 Choose a setup language
Fig. 1-3-1.4 Installation Startup
3-2. Install Witness Pro NVR software
You can use your new Network IP Camera by its web user interface v There is a NVR software CD
comes with IP camera which allow you run 32/64 channels IP cameras on a PC. Please follow the
steps below to complete the installation of Witness Pro NVR software.
While into Windows, and insert the I-View DVR software CD into a CD/DVD drive.
Select the NVR64 or NVR32 software
.
Step 3. Select the installation language and
press the “OK” button to continue.
.
Step 4. Press the “Next” button to start the
installation process..
Fig. 1
-3-1.1 Installation Menu

20
Step 5. Click the “Browse”button to install into
a different directory, otherwise click on
the “Next”button to install the software
into the proposed director.
Step 6. Select “No, I will restart my computer later”
and press on the “Finish”button to exit.
Fig. 1-3-1.5 Installation
Fig. 1
-3-1.9 Restart the computer