Anywhere Fireplace 90299 User manual

ANYWHERE FIREPLACE™
The high style and distinctive contemporary design of the Anywhere Fireplace™ allows the ambiance of a fire to be enjoyed in any room.
It is ventless, requiring no chimney or gas line because it uses clean burning bio-ethanol liquid fuel that is smokeless, odorless, and leaves
no soot or ash. You can hang the Anywhere Fireplace™ on any wall in your house, condo, apartment, office or restaurant. It is sure to
match most any décor and adds a rich warm atmosphere to your bedroom, living room, den, dining room… This unique, impressive,
eco-friendly modern answer to the fireplace creates a bright yellow, orange and red flame, spreading cheerful glow across the room. It is
non-toxic, non-polluting, has no messy clean up and is virtually free of maintenance. One quart of fuel can burn for up to 5 hours.
YOU WILL NEED
PENCIL, DRILL, LEVEL, TAPE MEASURE, HAMMER, SCREWDRIVER
INCLUDED ITEMS
www.anywherefireplace.com
Devco LLC
Larchmont, NY 10538
This product has been designed for your
enjoyment. Please carefully read all warnings
and installation instructions before use.
WALL BRACKET ANCHOR ANCHOR SCREW SPACER SPACER SCREW
BURNER HANDLE BURNERBURNER LID
X 2X4 X4 X4 X4
X 1X 1
FUNNEL
X 1X 1
Model: SoHo
For any questions related to parts or installation visit us on the web at www.anywherefireplace.com or email us at
[email protected]
QUESTIONS
Item #90299 Stainless Steel
Item #90200 Black Finish

PENCIL, DRILL, LEVEL, TAPE MEASURE, HAMMER, SCREWDRIVER
INSTALLATION
Choose a mounting location 4 ft away from flammable objects or materials (drapes, fabrics, furniture, etc.)
Be sure to remove all packing materials, cardboard, plastic, film etc
Fireplace must be installed on a wall and may not be used on the floor
Do not fill space between fireplace and wall with any insulating product. Leave area open to allow airflow
Make sure wall mounting brackets are secure to the wall and mounted upright (see diagram on next page)
The Anywhere Fireplace™ is ONLY to be used with bio-ethanol LIQUID fuel for fireplaces. The bio-ethanol fuel is a flammable product
that requires strict adherence of the safety instructions.
This fireplace will produce heat, but should not be used as a main source of heat
This fireplace is intended to be wall mounted and must not be set on the floor
Be sure to keep any flammable materials such as drapes/curtains and any decorations at least 4 ft away from fireplace
Do not place any items on top of or inside fireplace
Do not touch the fireplace while lit or still hot
USE ONLY APPROVED BIO-ETHANOL LIQUID FUEL FOR FIREPLACES
It is extremely dangerous and forbidden to use bio-ethanol car fuel or any other unapproved fuel
Never fill the burner more than 2/3 full
Never add fuel to the burner while fire is burning or unit is still hot. Allow at least 15 minutes for fuel tray to cool
before refueling
Do not ingest bio-ethanol fuel and avoid contact with eyes and skin
Be sure to not spill any fuel outside of the fuel tray. If you do spill, make sure to wipe up all spillage before igniting the fire
Only use a long match or long lighter to ignite fire
Be sure to have a fire extinguishing device in the proximity of the fireplace in case of emergencies
Never leave a lit fireplace unattended
Be sure to keep children and pets away from the fireplace while lit and while still hot after extinguishing
Do not smoke when filling the fireplace with fuel
Store your fuel containers away from any heat source
Be sure to store and keep your fuel away and out of reach of children and pets
To adjust flame height, use supplied burner handle to open/close burner lid
To extinguish flame, use supplied burner handle to close burner completely
It is forbidden to modify this fireplace in any way
IMPORTANT SAFETY MEASURES
WARNING
FUEL INFORMATION
USE ONLY APPROVED BIO-ETHANOL LIQUID FUEL FOR FIREPLACES
Bio-Ethanol Liquid Fuel for fireplaces burns clean without emitting any toxins into the air. Only harmless water vapor and CO2are
produced as byproducts
Anywhere Fireplace Bio-Ethanol Liquid Fuel may be purchased at www.anywherefireplace.com.

Step 2
Using a 3/8” drill bit, drill holes into the wall on the 4 spots where you marked the bracket hole
locations.
Step 3
Insert the wall anchors flush into holes in wall as shown above. A light tap with a hammer might
be necessary to insure it is inserted flush with the wall. If you drill a hole into a wooden stud, the
plasic wall anchor is not necessary.
NOTE: The wall anchors provided are intended to be used in drywall. If mounting on another
wall surface, make sure you have the proper mounting hardware.
Use a level to mark a straight line with a pencil on the wall where you will mount the brackets.
The wall should be made from drywall, tile, brick, stone, etc. It must not be flammable (e.g. no
wallpaper or wood) Make sure you mount the fireplace at least 4 feet away from any drapes or
flammable materials.
The inside edges of the brackets should be spaced 4 inches apart. Mark bracket hole locations on
the wall with a pencil keeping them level with the line previously drawn.
MOUNTING INSTRUCTIONS
To UPDATE:
Bit size will
change

Step 4
Place brackets over holes of anchors and attach to the wall by inserting the screw through the
bracket into the anchors in the wall. Make sure brackets are attached in the proper position.
See above illustration for reference.
Step 5
Using a screwdriver, attach wall spacers to the back of the fireplace in the predrilled holes using
the spacer screw. If they are already attached, insure it is on securely.
Step 6
Hang fireplace on the wall by placing the open slots on the back of the fireplace onto the
mounted brackets.
Insert burner into fireplace and cover with the provided burner lid. Using funnel, fill 2
/3full with
LIQUID bio-ethanol fuel. Light using a long lighter or long match and enjoy!