Anywire ARW-03 User manual

AnyWire Remote head for Address Writer
ARW-RH
ARW-03ARW-04
AnyWire System Product Guide (Product Manual)
-ARWRH 1/6-
POWER
The Product Guide describes individual products. Refer to the Guide as necessary.
[Notes on Safety]
Precautions that must be observed in order to use this system safely are indicated as shown below.
You must observe these precautions.
WARNING CAUTION
A WARNING indicates a potentially hazardous
situation which, if not handled correctly, could
result in death or serious injury.
ACAUTION indicates a potentially hazardous situation
which, if not handled correctly, may result in personal
injury or property damage.
WARNING
○System Safety
○Always turn off the power before attempting to mount or replace.
This system is intended for general industrial applications. It does not have functions for supporting applications requiring higher
levels of safety such as safety-related devices or accident prevention systems. The product must not be used for these purposes.
○Use the AnyWire System within the range of the specications and conditions shown below.
○System power supply
○Separately route high-voltage and power cables
○Connectors and terminals
○Do not impose any external loads on the units. Doing so may cause a failure.
○Do not disconnect or reconnect between the transmission line and slave units. A malfunction may occur.
Use a stable, 24V DC power supply. Use of an unstable power supply may cause problems with the system.
Although the AnyWire System has a high noise margin, keep the transmission line and I/O cables away from high-voltage and
power cables.
・
Pay careful attention to the length and installation of cable wiring to ensure that connectors and cables are neither overloaded nor disconnected.
・Make sure to prevent any metal objects from getting inside the connectors or the terminal blocks.
・Short-circuits caused by metal objects or mis-wiring are likely to damage the device.
CAUTION
[Features]
■Warranty period
The warranty on the delivered Product shall continue to be effective for
one (1) year after the delivery thereof to a location as designated by the
original owner.
■Scope of warranty
Should a defect occur in any part of the Product during the foregoing
warranty period when it is used normally in acordance with the specica-
tions described in this User's Manual, the Company shall replace or
repair the defect free of charge, except when it arises as a result of:
[1] Misuse or abuse of the Product by the owner;
[2] Fault caused by other than the delivered Product;
[3] The unauthorized modication or repair of the Product by any person
other than the Company's personnel;
[4] Any unusual force of nature, disaster or other cause beyond the Com-
pany's control.
The term "warranty," as used herein, refers to the warranty applicable to
the delivered product alone. The Company shall not be liable for conse-
quential or incidental damages resulting from any malfunction.
■Repair at cost
After the expiration of the warranty period, the owner shall be responsi-
ble for all costs and expenses incurred for the troubleshooting and repair
of the Product. Even during the warranty term, the Company shall repair
any defects arising from causes other than within the scope of the
warranty as specied above, at the owner's cost.
- It is connected to AnyWire infrared non-contact address writer before use.
(Only RH connector built-in model)
- It makes writing in a narrow space or small-sized unit difcult to be
handled by the body of address writer easier.
- Front communication and side communication are available.
[Warranty]
[Type]
ARW-RH ARW-04
ARW-03
Adaptable model

-ARWRH 2/6-
POWER
POWER
①
②
* This gure shows an ARW-04 as an example.
[Operation method]
SET button
As for the operation method of the ARW-03 and ARW-04, please refer to the other sections.
■Writing
Set address values to be written in the ARW-04 or ARW-03 in advance.
Point the optical axis window of the ARW-RH to the address writing port of the target unit.
Press the SET button on the ARW-04 or ARW-03 to write an address value.
When writing is successful, a beep sounds.
When “ERR” is displayed, readjust the optical axis to press the SET button again.
■Reading
Set the ARW-04 or ARW-03 to the reading mode in advance.
Point the optical axis window of the ARW-RH to the address writing port of the target unit.
Press the SET button on the ARW-04 or ARW-03 to write an address value.
When writing is successful, a beep sounds.
When “ERR” is displayed, readjust the optical axis to press the SET button again.
* This gure shows an ARW-04 as an example.
[Connection method]
Turn off the ARW-04 or ARW-03, ①remove the cover on the RH connector part and ②connect the connector of the ARW-RH.
To RH connector
ARW-RH

-ARWRH 3/6-
[Operating distance]
Unit for writing
Light receiving part
Light receiving part
Basically, operation within the range of
approx. 30mm is possible.
If a unit is small, move the remote head
as close as possible to the unit.
Unit for writing
Light
receiving
part
Light receiving part
Basically, operation within the range of
approx. 30mm is possible.
If a unit is small, move the remote head
as close as possible to the unit.

-ARWRH 4/6-
* This gure shows an ARW-04 as an example.
[Example of selection of optical axis]
Unit for writing
Light emitting
and receiving axis
Change the optical axis selection switch
to the orange side.
Light receiving part
Light receiving part
1. When the surroundings are narrow
but writing from the front is possible
Light emitting
and receiving axis
Change the optical axis selection switch
to the orange side.
Light receiving part
Light receiving part
Unit for writing
2. When the surroundings are narrow
and writing from the side is required
Unit for writing
Light emitting
and receiving axis
Light receiving part
Light receiving part
3. When the surroundings are relatively
wide and writing from the front is
possible

-ARWRH 5/6-
POWER
■Connecting location
RH connector
To RH connector
ARW-03ARW-04 Side of both models
(1000)
75
20
16.4
Unit: mm
■Model of remote head: ARW-RH (with a connecting cable 1m)
[Outer dimensions]

-ARWRH 6/6-
Anywire Corporation
Headquarters :1 Babazusho, Nagaokakyo-shi, Kyoto 617-8550 JAPAN
:Contact by mailContact [email protected]
:Contact by website http://www.anywire.jp
Printed in Japan 2011, 2016, 2017 UMA-08326C-EN
[Address]