AOC L19WA91 User manual

19″&22″LCDTV AOCL19WA91&L22WA91
1
Service
Service
Service
Horizontal Frequency
31.5~60kHz
TABLE OF CONTENTS
Description Page Description Page
SAFETY NOTICE
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS
AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING
ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING
6.1 Main Board…………..……………...…….…….......29
6.2 Power Board……………..……….…….……….......31
6.3 Key Board………………………..……..……….......32
6.4 IR Board………………………….……..……….......33
7. Adjustment……..………………………….................34
8. Block Diagram.…….................................................35
9. Schematic Diagram…..…………....………………...36
9.1 Main Board…………………………………...….......36
9.2 Power Board…………….…………...………….......50
9.3 Key Board……………….……….…………….........52
9.4 IR Board……...………….……….…………….........53
10. Exploded View………………………………….…...54
11. BOM List……………….………………….………….56
Table of Contents........……...................................…........1
Important Safety Notice.......................................……......2
Revision List…………………………………………………3
1. General Specification..............................……...…........4
2. Operating Instructions………………...…….……….......5
2.1 The Use of Remote Control…….…..……….…….......5
2.2 To Use The Menu…....…………………….……….......6
2.3 How To Connect……..……………….…….………....13
2.4 Front Panel Control Knobs…….………….……….....15
3. Input/Output Specification…………....................…....16
4. Mechanical Instructions…………………….................19
5. Repair Flow Chart ……………………….…….…….....24
6. PCB Layout ………………..…………………....….......29

2
Important Safety Notice
Proper service and repair is important to the safe, reliable operation of all AOC Company Equipment. The service
procedures recommended by AOC and described in this service manual are effective methods of performing service
operations. Some of these service operations require the use of tools specially designed for the purpose. The
special tools should be used when and as recommended.
It is important to note that this manual contains various CAUTIONS and NOTICES which should be carefully read in
order to minimize the risk of personal injury to service personnel. The possibility exists that improper service
methods may damage the equipment. It is also important to understand that these CAUTIONS and NOTICES ARE
NOT EXHAUSTIVE. AOC could not possibly know, evaluate and advise the service trade of all conceivable ways in
which service might be done or of the possible hazardous consequences of each way. Consequently, AOC has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not
recommended by AOC must first satisfy himself thoroughly that neither his safety nor the safe operation of the
equipment will be jeopardized by the service method selected.
Hereafter throughout this manual, AOC Company will be referred to as AOC.
WARNING
Use of substitute replacement parts, which do not have the same, specified safety characteristics might create
shock, fire, or other hazards.
Under no circumstances should the original design be modified or altered without written permission from AOC.
AOC assumes no liability, express or implied, arising out of any unauthorized modification of design.
Servicer assumes all liability.
FOR PRODUCTS CONTAINING LASER:
DANGER-Invisible laser radiations when open AVOID DIRECT EXPOSURE TO BEAM.
CAUTION-Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
CAUTION -The use of optical instruments with this product will increase eye hazard.
TO ENSURE THE CONTINUED RELIABILITY OF THIS PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S
REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART NUMBERS IN THE PARTS LIST SECTION OF
THIS SERVICE MANUAL.
Take care during handling the LCD module with backlight unit
-Must mount the module using mounting holes arranged in four corners.
-Do not press on the panel, edge of the frame strongly or electric shock as this will result in damage to the screen.
-Do not scratch or press on the panel with any sharp objects, such as pencil or pen as this may result in damage to
the panel.
-Protect the module from the ESD as it may damage the electronic circuit (C-MOS).
-Make certain that treatment person’s body is grounded through wristband.
-Do not leave the module in high temperature and in areas of high humidity for a long time.
-Avoid contact with water as it may a short circuit within the module.
-If the surface of panel becomes dirty, please wipe it off with a soft material. (Cleaning with a dirty or rough cloth may
damage the panel.)

3
Revision List
Version Release Date Revision Instructions Customer Model TPV Model
A00 Aug.11,2009 Initial Release
L19WA91 E19922NB4WACNN
L22WA91 E22922NB4WACNN
A01 Apr.22,2010 Add new models
L19WA91 E199C2NB4WG22N
L22WA91 E229G2NB4WG22N

4
1. General Specification

5
2. Operating Instructions
2.1 The Use of Remote Control

6
2.2 To Use the Menus
OSD Settings
1. Press the MENU button on the side of the TV or press the MENU/EXIT button on the remote control to display or
close the main menu.
2. Use the Navigation Ring to move around to select, adjust or confirm an item in the OSD (On Screen Display)
menu.
Menu Descriptions
Picture Show more picture modes and functions based on your favourite channels and enables you to adjust
the colour and brightness setup.
Sound Provide more audio selections. You can also set the audio environment of the TV.
TV Enable you to adjust special functions for country, audio language and the TV channel.
Features Enable you to adjust settings of the TV channels and language.
Parental Enable you to control special functions for the TV channels.

7
Picture
Menu Descriptions
Smart Picture To set the best picture appearance to a predefined picture setting from Standard,
Vivid, Movie, Eco, or Personal.
Brightness To brighten the dark parts of the picture.
Contrast To sharpen the picture quality.
Colour To add or reduce colour.
Tint To adjust the picture tint.
Sharpness To improve detail.
Colour Temperature To choose between Normal (neutral), Warm (redder), and Cool (bluer).
Advanced Control
Noise Reduction To filter out and reduces the image noise and improve picture quality.
Select the effect degrees from Off, Low, Medium, High, or Auto.
Flesh Tone To adjust the skin colour to be more natural.
Back light To make the background colour brighter or darker.
DCR Dynamic Contrast Ratio (DCR) auto adjusts the brightness of the screen to show
more depths in the darker areas.
Wisdom Light (32”/42”
with light sensor model
only)
To enable the light sensor to adjust brightness automatically by detecting ambient
light. Set the sensor on or off.
HDMI mode (HDMI only)
User can select Auto/graphic/Video mode. Description as following:
Auto
Automatic to get device information, device will indicate sending timing is video
timing or graphic timing (PC timing).
Graphic
Force video timing shows as graphic timing, for example: 720p shows
1280x720@60Hz; 1080p shows 1920x1080@60Hz. This mode optimises for PC
input.
Video
Force graphic timing shows as video timing, for example: 1280x720@60Hz shows
720p; 1920x1080@60Hz shows 1080p. This mode optimises for DVD player,
camcorder, and other video appliances inputs.

8
Sound
Menu Descriptions
Sound
Mode To set the TV to a predefined sound setting from Personal, Music, or Speech.
Balance To adjust the balance between left and right channels.
Virtual
surround To add greater depth and dimension to the TV sound.
Digital
Audio Out
To select the Digital Audio Out from Off, Dolby Digital, or PCM. Tip: When Dolby Digital is selected,
make sure the amplifier supports digital audio.
SPDIF
Delay
SPDIF Delay function will affect SCART/Line out audio also delay at that time. The NorDig HD IRD
shall support the possibility to adjust the audio-delay on the SPDIF output (if available) up to 250
ms and it should be adjustable in 10ms steps, as the IRD may have several different user set-ups,
resulting in different a/v delays; e.g. the IRD may be connected to several types of external
audio-amplifiers and the STB may be connected to several types of external screens.
AVL To eliminate the volume differences between channels and programs and reduce the dynamics of
sound.
The following functions are only available for digital channels with audio signals.
Type
This function enables you to choose the type of the additional narration during the TV watching
from Normal, Hard of Hearing, or Audio Description. Hard of Hearing: This function provides
narration to deaf and hard of hearing viewers.
Audio
description When the Type is set to “Audio Description”, you can adjust the volume of the audio description.

9
TV
Menu Descriptions
Country To select the relevant country. This is the country you are in, or the country whose channels
you want to receive if you live near its borders.
Audio Carrier
(ATV only) Select Stereo, Dual 1, Dual 2, or Mono for ATV channel.
1st and 2nd
Audio
Use this function when two or more audio languages are broadcast. This is the language to be
used for digital channels if it is available.
Channels
Enter the channels submenu, and choose from Channel Scan, Update Scan, Single RF Scan,
Analog Manual Scan, Channel Skip, Channel Sort, Channel Edit, Decoder, and Analog CH
Fine Tune.

10
TV/Channels
Menu Descriptions
Channels
Channel scan
Channel Scan will re-tune the television automatically. It is recommended to run the Channel Scan
periodically to ensure that all new services are added.
Update scan
Search the new channels automatically that are not in the channel list.
Single RF Scan (Digital Only)
Enter the Single RF Scan in the Channels submenu to scan digital channels.
Analog Manual Scan
The television can be tuned-in manually using Analog Manual Scan. Use the number keys to enter
the Start Frequency to scan up or scan down.
Channel skip
To prevent certain programs from being viewed by pressing CH + / - buttons on the remote control,
the program position can be skipped. Tip: The skipped program may not be found by pressing CH + /
- buttons but can be access by pressing number buttons directly.
Channel sort
Change the order of the Channel List.
Channel Edit
Enter the Channel Edit in the channels submenu to edit the channel number and channel name by
using the number buttons 0~9. Note: The following RC number-mapping table will not be shown on
the TV screen.
Decoder (Analog only)
Channel Decode support the Canal+ (paid television channel); however, the channel also broadcast
some un-encrypted programs. These programs without encryption can be viewed free of charge.
Analog CH Fine Tune
Select Analog CH Fine Tune in the Channels submenu to adjust the frequency.

11
Features
Menu Descriptions
Menu Language To select the on-screen display menu language.
Picture Format To select the available display format from Auto, Normal, Native (HDMI only), Wide, Zoom 1,
or Zoom2.
Time setup
Time Zone
To select the time zone you are in.
Time
To set the time and date or select auto synchronization. Tip: Before you want to set the time
and date by your own, please make sure Auto synchronization is Off.
Sleep Timer
To set the TV to turn itself off within a certain time.
Subtitle
Analog Subtitle
To display the transmitted subtitle on the screen. Either this text can be permanently
displayed (assuming that the service is available in the broadcast) or only when mute is
active.
Digital Subtitle
Use the Digital Subtitle function when two or more subtitle languages are broadcasted. If
subtitle data in a selected language is not broadcasted, the default language subtitle will be
displayed.
Subtitle Type
To choose the subtitle type from normal or hearing impaired.
Teletext
Language
Digital Teletext Language
To select the teletext language.
Decode Page Language
To set the teletext language to the regional location.
Common
Interface This menu appears with your CI supplier information.
HDMI Scan Info
(HDMI only)
Automatic
Set to underscan or overscan automatically when the video signal is detected.
Underscan
When the video signal is detected, all active pixels and lines are displayed with or without
border.
Overscan
When the video signal is detected, some active pixels and lines at the edges are not
displayed.
Reset Default To reset all TV settings to the original factory values.

12
Parental
Menu Descriptions
Channel
Block To block certain TV channels.
Parental
Guidance
To control access programs based on their age ratings. All settings apply to digital channels. Note:
This function operates according to information from the broadcasting station. Therefore if the
signal has no information, this function does not operate.
Input Block To disable the specific external input signals.
Set
Password
To set or change your password. Please follow the instructions to set it. All member combinations
from 0000 to 9999 are valid. Tip: Remember that 5351 is the default Change Password code. If
your access code has been changed or you have forgotten the code, you can always get in by
inputting the default code.
Clear All To clear all the settings in the parental submenu.

13
2.3 How to Connect

14

15
2.4 Front Panel Control Knobs

16
3. Input/Output Specification
3.1 RGB Signal Input
15 - Pin Color Display Signal Cable
Pin No. Description Pin No. Description
1 Red Video 9 +5V(Supply From PC)
2 Green Video 10 Sync Ground
3 Blue Video 11 NC
4 NC 12 Bi-directional Data(SDA)
5 Ground 13 H-Sync.
6 Red Video Ground 14 V-Sync.
7 Green Video Ground 15 Data Clock(SCL)
8 Blue Video Ground
3.2 HDMI Digital Connector Pin Assignments
Pin No. Description Pin No. Description
1 TMDS Data2+ 2 TMDS Data2 Shield
3 TMDS Data2- 4 TMDS Data1+
5 TMDS Data1 Shield 6 TMDS Data1-
7 TMDS Data0+ 8 TMDS Data0 Shield
9 TMDS Data0- 10 TMDS Clock+
11 TMDS Clock Shield 12 TMDS Clock-
13 CEC 14 NC
15 SCL 16 SDA
17 DDC/CEC Ground 18 +5V Power
19 Hot Plug Detect

17
Full Scart Connector Pin Assignments
Pin No. Description Pin No. Description
1 Audio Output Right 12 N.C.
2 Audio Input Right 13 GND(Red)
3 Audio Output Left 14 GND(Blanking)
4 GND(Audio) 15 Red Input
5 GND(Blue) 16 RGB Switching Control
6 Audio Input Left 17 GND(Video Input & Output)
7 Blue Input 18 GND(RGB Switching Control)
8 Switch Signal Input (Fast
Blanking) 19 Video Output(Composite)
9 GND(Green) 20 Video Input(Composite)
10 N.C. 21 Common Ground
11 Green Input
3.3 Video/Audio Signals
·TV RF input system -Aerial or cable should support PAL/SECAM/DVB-T
·TV RF input level -10mV (80dBuV) typical, 30dBuV ~ 100dBuV receiving capability, terminated with input
impedance of 75Ω.
·CVBS input -1000mVpp (including 300 mV sync level), terminated with input impedance of 75Ω.
·Component video input -Y: 1000mVpp (include sync), PbPr: 700mVpp terminated With Input impedance of 75Ω.
Support 480i/p, 576i/p, 720p, 1080i at 50Hz or 60Hz refresh rate
·Audio input -Sensitivity 500mV (rms). For rated power, the amplifier should be able to handle input
signal up to 2.0V, input impedance > 10KΩ.
·SCART input / output -Full SCART, includes RGB in, CVBS (audio L/R) in/ (TV out). Half SCART includes
S-Video in, CVBS (audio L/R) in/ (TV out).
·HDMI (High Definition Multimedia Interface)
-Support 480i /480p, 576i/576p, 720p, 1080i format with HDCP
-Digital interface with 4 channels TMDS signal
·CISlot -PCMCIAcard5Vinput.
·PC VGA input -700 mV input level, TTL level sync, RGB in, 75Ωimpedance.
·PC Audio input -500 mVrms input level, impedance > 10 kΩ.
·SPDIF output -Level: +/- 0.5V Square Wave.
·Amplifieroutput -3W+/-10%
·Speaker -8Ω

18
3.4 Compatible Mode Table
Vesa Modes
Horizontal Vertical
Mode Resolution
Nominal
Frequency
(KHz)
Sync
Polarity
Nominal
Freq.
(Hz)
Sync
Polarity
Nominal
Pixel
Clock
(MHz)
VGA
640x480@60Hz 31.469 N 59.940 N 25.175
640x480@72Hz 37.861 N 72.809 N 31.500
640x480@75Hz 37.5 N 75 N 31.500
720x400@70Hz 31.469 N 70.087 P 28.322
SVGA
800x600@56Hz 35.156 P 56.25 P 36.000
800x600@60Hz 37.879 P 60.317 P 40.000
800x600@72Hz 48.077 P 72.188 P 50.000
800x600@75Hz 46.875 P 75 P 49.5
XGA
1024x768@60Hz 48.363 N 60.004 N 65.000
1024x768@70Hz 56.476 N 70.069 N 75.000
1024x768@75Hz 60.023 P 75.029 P 78.750
WXGA
1280x720@60Hz 45 P 60 P 74.25
1280x768@60Hz 47.396 P 59.995 N 68.25
1360x768@60Hz 47.712 P 60.015 P 85.5

19
4. Mechanical Instructions
1. Remove the 3 screws to remove the stand base.
2. Remove the screws to remove the rear cover.

20
3. Release connectors.
L19WA91
L22WA91
.