AOpen FM56-ITU/2 User manual

AOpen Fax/Modem Series
Thank you for choosing AOpen Fax/Modem. This file will guide you for
installation and AT commands.
AOpen FM56-ITU/2 Manual
AOpen FM56-ITU/2 AT Commands

FM56-ITU/2 Manual
Published in 2000
All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any
language or computer language, in any form or by any means, electronic,
mechanical, magnetic, optical, chemical, manual or otherwise, without the
prior written consent of the manufacturer.
Disclaimer
The manufacturer makes no representations or warranties with respect to the
contents hereof and specifically disclaims any implied warranties of merchant
ability or fitness for any particular purpose. Furthermore, the manufacturer
reserves the right to revise this publication and to make changes from time to
time in the content hereof without obligation to notify any person of such
revisions or changes.
Trademarks
The manufacturer does not claim any trademark that appears in this
publication. All names, brands, products or services are trademarks or
registered trademarks of their respective companies.
Table of Contents
1 Introduction
2 Feature
3 Parts And Functions
3.1 PC Card Connection
3.2 PC Card Bracket Connection
4 Installing The Fax/Modem
4.1 Checking Your Components
4.2 What Else You Need
4.3 Installing The PC Card Fax/Modem
4.4 Connecting To The Telephone Line
4.5 Connecting To You Telephone Set
4.6 Verifying Your Connection
4.7 Connecting Microphone And Speaker
4.8 Voice Function Alternatives
4.9 Configuring Internal Modem With Windows3.1/95/98/2000/NT

4.10 Tips On Configuring Your Communication Software
4.11 Tips On Configuring SVD
5 Executing Commands
6 S-Registers
7 Response Sets
8 Specifications
Appendix A: FCC Compliance
A.1 FCC Notice
A.2 FCC Requirement
Appendix B: Default Profiles

FM56-ITU/2 AT Commands
Table of Contents
1 Hayes Compatible AT Command Set
2ECC Command Set
3List Of Class 1 Fax Commands
4List Of Class 2 Fax Commands
5List Of Voice Commands (Voice Models Only)

1 Introduction
Congratulations on purchasing a state-of-the-art fax/modem! Your
Fax/Modem incorporates the latest technological advancement for you to
electronically communicate with other computers, information networks, fax
machines or other fax/modems. It embraces most of the industry and
commercially popular standards to ensure compatibility with most equipment
and application programs. The voice capability renders a wide range of
application possibilities from a simple telephone-answering device to a
sophisticated voice-mail system. The SVD feature allows you to talk and
transmit data at the same time.
This manual includes instructions on installing, connecting and setting your
Fax/Modem. A section on diagnostics using loopback test is also included to
help you isolate problems that may occur anywhere from the computer
interface to the modem at the remote site.

2 Feature
•Line rate of 56 Kbps for download (FM56 series model only)
•ITU-T V.90 specifications for operation at speed of 56,000 bps.
•MNP10 dynamic data rate fallback and forward on the run.
•Software controlled speaker volume.
•Software selectable flow control.
•Voice option for voice mail application.
•SVD for simultaneous voice and data. (Optional)
•Uses 16550/A compatible enhanced UART for sustained DTE speed of
115,200 bps.
•Zero-Voltage Modem wake-up function
•Cooperate with the sound card setting in your computer. (Optional)

3.1 PC Card Connection
FM56-ITU/2
JP13 : Sound Interface Pin Define (Optional)
For connectingtoAOpen AudioCard.
JP18 : Ring Wake Up Interface Pin Define (Optional)
For connecting to AOpen Mother Board.
COM Port Setting
Port HEX ADDRESS JP1 JP2
COM 1 3F8 to 3FF On On
COM 2 2F8 to 2FF On Off
COM 3 3E8 to 3EF Off On
COM4 (Default) 2E8 to 2EF Off Off
IRQ Setting (Default: IRQ 3)
JP 3 4 5 6 78 910 11
IRQ 3 4 5 7 910 11 12 15

3.2 PC Card Bracket Connection

4.1 Checking Your Components
Unpack your fax/modem and make sure you have the following items:
•The fax/modem.
•A modular telephone cable to connect your fax/modem to the telephone
line.
•Communication software.
•Two cables link JP13 and JP18 to sound card and mother board
When you open your package, make sure all of the above items are included
and not damaged. If you see that any components are damaged, please notify
your dealer immediately.

4.2 What Else You Need
To complete your data communication system, you will need the following
items:
Other communication software, if needed.
An active telephone line and telephone set (if you need to use a telephone
with your modem).
An available ISA card slot in the personal computer.
For voice function, a microphone and a speaker for voice recording and
playing (voice function can also be performed by handset of telephone set
connected to fax/modem).