Apollo REACH WIRELESS RW1700-030APO User manual

UNBOXING
•
• The Translator is housed in an IP Rated box, with knock-outs for IP-rated glands.
• 4 plastic screws are provided to secure the lid.
For more information, please refer to the user manual. Available on apollo-fire.co.uk
IMPORTANT TO CONSIDER
When mounting a wireless device, a comprehensive radio survey
should have been carried out to establish the location that provides
the best coverage and optimum reach. Taking into consideration the building
structure and materials, the survey identifies the wireless infrastructure
required and product locations for optimum performance, identifying
any factor that could prevent radio integrity.
Avoid fixing or mounting the unit close to the following:
• Equipment that utilises large electrical currents
• Large metal objects or structures
• Fluorescent lighting fittings
• Metal ceiling structures
• IT cabling.
Keep 2 meters minimum spacing between other wireless equipment
in the area to avoid signal interference.
EN54 approved environmental temperature range is -10°C to +55°C
MOUNTING STEPS
The Translator Module is IP65 rated, suitable for external mounting. The backbox must be installed on the wall
as flat as possible to retain IP-rating, to prevent distortion of the housing and the ingress of contamination and/or moisture.
Proceed as follows to complete the device installation.
Remove top and bottom front plastics that cover screws,
unscrew all four screws and remove the lid fromthe backbox.
1
3
2
4
5
Using a suitable-sized drill bit (4mm) drill the pre-defined
screw mounting points in the 4 corners of the backbox.
6
SCREWS
Remove the electronic PCB assembly from the enclosure.
The PCB is held by two Philips screws below the display,
it then slides up and out.
Prepare apertures (20mm knockouts) required for cable
access and fit appropriate rated glands.
Screw the backbox to the wall using all fixing holes
and appropriate-sized roundhead screws (do not use
countersunk screws). Insert cable,tighten glands and refit PCB and securing screws.
MOUNTING HOLES
SCREWS HOLES
NO
YES
INSIDE THE BOX
• 1 x Loop Interface Module
• 4 x Screws
• 1 x Quick start guide
QUICK START GUIDE
The Translator has removable top and bottom frontplastics to cover screw housings.
RW1700-030APO
REACH XP95 Loop Interface Module
Apollo Fire Detectors Ltd. 36 Brookside Road, Havant, Hampshire, United Kingdom, PO9 1JR
T: [phone] - E: techsales@apollo-fire.com - W: www.apollo-fire.co.uk RW_IG_LOOP_INTERFACE_REV_A.1
THE BOX
Product Part Number
Product Description
RW1700-030APO
REACH XP95 Loop Interface Module
RW1700-030APO
Scan QR code
for full user manual

The Loop connector on the top of the translator board should
be wired to the Panel of your choice, from the left to right
the terminals are:
• Loop In Negative wired to Loop Out Negative on the Panel
• Loop OutNegative wired to Loop In Negative on the Panel
• Loop In Positive wired to loop Out Positive on the Panel
• Loop OutPositive wired to LoopIn Positive on the Panel.
7
9
8
10
The translator will power up and the translator will be ready
for commissioning phase.
• If connecting a wired EN54-4 PSU (optional) there are
2 terminals for the connections from the power side
of the PSU.
• There are also terminals for FaultMonitoring using a feed.
• Ensure you select the correct jumper position.
• Screw the lid to the backbox using the supplied plastic
screws and refit top and bottom front plastics that cover
screw housings.
GREEN LED
MAINS FAULT
PULL-UP TO 3V3
BATTERY FAULT BATTERY
CHARGER FAULT
BATTERY O/C
ext. power (-) ext. power (+) JUMPER
SELECTION
LOOP IN (-)
LOOP OUT (-)
LOOP OUT (+)
LOOP IN (+)
QUICK START GUIDE
RW1700-030APO
REACH XP95 Loop Interface Module
Apollo Fire Detectors Ltd. 36 Brookside Road, Havant, Hampshire, United Kingdom, PO9 1JR
T: [phone] - E: techsales@apollo-fire.com - W: www.apollo-fire.co.uk RW_IG_LOOP_INTERFACE_REV_A.1