AppNeta RE-9123 Manual

RE-9123
SHEET # 1
SetUp Instructions

RE-9123
SHEET # 2
TOWER
HEADER- R
HEADER- L
KIOSK- L
WITH
RE-1202 COUNTER
KIOSK- R
WITH
RE-1202 COUNTER
RECEPTION
COUNTER
RE-1250
COUNTER
RE-1207
COMPONENTS

RE-9123
SHEET # 3
TOWER PARTS
2
corner
34
5
corner
door
6
corner
A5
corner
A15 A14
corner
A6
A7 A8
corner
A13
A10
above
door
A11
corner
7
lower back
8
lower back
9
corner
A12
A4
connector
bracket
W/ hinge
A9
connector
bracket
w/hinge

RE-9123
SHEET # 4
TOWER COUNTER RE-1207
door side
assembled
door side assembled
Center assembed
At tach Back
beams w/sintra
At tach front
beams
velcro sintra to front
Attach top to completed frame

RE-9123
SHEET # 5
HEADER PARTS
1
A1
A2
A3
FRAME SHIPPED
ASSEMBED
GRAPHIC A
GRAPHIC A
GRAPHIC A
GRAPHIC B
GRAPHIC B
B1
B2
11
B3
LOCK HEADER FRAMES
INTO HINGE ON TOWER
CUSTOM CORNER CONNECTORS

RE-9123
SHEET # 6
A1
1
11
B3
Side with door
assembled
Side with door
assembled
side assembled
side assembled
velcro front
panel on
attach front & back
horizontals wit h infil
to sides
attach front & back
horizontals wit h infil
to sides
set top
on compled counter
set top
on compled counter
attach wings
with C clamps
attach wings
with C clamps
Kiosk-L
Kiosk-R
Counter to Upright connection
S
EG G
rap
hic
Bolts
Standoff
Barrel
Attachment
Monitor Mount
S40
Monitor Mount Attachment
*
Slide connector on back of standoff
barrels into grooves of S40 verticals;
turn barrel clockwise to tighten
in place.
Attach Monitor Mount to
standoff barrels using bolts.
Stand-Off
Barrels
Note: Monitor mount installs over SEG graphic.
Screws
Connector
Piece
Connector Detail
1) Slide connecter piece into
vertical extrusion and
secure with screws.
2) Slide upper vertical on connector
and atop lower vertical, then
secure with screws.
*Keep all screws attached to
connector piece when
disassembling to prevent loss*
Kiosks

RE-9123
SHEET # 7
RECEPTION COUNTER RE 1250

RE-9123
SHEET # 8
RECEPTION COUNTER RE 1250

RE-9123
SHEET # 9
RE-1250 Front (Ships Assembled)
RE-1250 Counter Side
(Ships Disassembled)
RE-1250 Counter Side
(Ships Disassembled)
RE-1250 Door
(Ships Assembled)
countertop
upper countertop
RECEPTION COUNTER RE 1250

RE-9123
SHEET # 10
TS V4 Locks for Gravitee
Rotate knob clockwise to tighten.
Packing note for Gravitee panels:
Gravitee Panels Side-by-Side Assembly
1) Frames: Place frames side-by-side with one higher
than the other, then slide panel down to lock panels
together and in place.
2) Corner Connections: Repeat Step 1 for installing
corner connections to frames.
Assemble Disassemble
Pull panel up to
disassemble
Push Panel in
with thumb to
disengage lock.
Stacking Unstacking
Gravitee Panels Stacking Assembly
1) Place one horizontal frame on top of the other lining up the center
grooves.
2) Turn the pin clockwise to tighten the stacking lock into place.
Repeat for each pin.
Stacking Disassembly
1) Turn the stacking lock counter clockwise to
loosen the pin.
2) The whole spring on the stacking lock should be in view to
release each frame. The spring should release the locking pin.
If not, turn the pin until it disengages.
Push Stacking Lock into the slot
of the upper frame then spin the
cap to tighten the lock.
Disengage the Stacking Lock by
spinning the cap counter
clockwise and pulling down.
NOTE:
Gravitee panels are
separated with small metal
pieces for stability during
shipment.
Keep all pieces for repacking.
Do not throw away.
Push Stacking Lock into the slot
of the upper frame then spin the
cap to tighten the lock.
Push lock into
the channel of
CEI extrusion.
Turn cap clockwise
to tighen lock
into place.
Note: Block on lock cap
will secure in groove.
CEI Frame
Gravitee
Panel
Gravitee to CEI Frame Connection
*
Profile View
SEG
grooves
GENERAL INSTRUCTIONS - GRAVITEE

RE-9123
SHEET # 11
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
LADDERS OR LIFTS
MAY BE REQUIRED
SEG Graphic Installation
Corner A
Corner D
Corner B
Corner C
It is important to first insert
graphic into each alternate
corner, then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Graphic Removal
To remove the graphic from
the frame, locate the fabric
pull tab. Gently pull up on
the tab to remove the fabric.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
GENERAL INSTRUCTIONS - EXTRUSIONS/SEG