Aqua Creek Products SPA LIFT ULTRA User manual

Copyright © 2019 Aqua Creek Products All Rights Reserved Revised 8/22/19
9889 Garrymore Ln
Missoula, MT 59808
888-687-3552 | [phone]
www.aquacreek.com
PART #: F-005SLU-04
US PATENT NUMBER: [D507,769 S]
400 LB. [181 kg] MAXIMUM WEIGHT CAPACITY
FOR INDOOR OR OUTDOOR USE
MANDATORY
LEAVE THIS MANUAL WITH LIFT OWNER
ADA COMPLIANT
Check entire box and inside all packing materials for parts. Before beginning assembly, read the
instructionsandidentifypartsusingtheguresandpartslistedinthisdocument.
It is critical all parts be carefully inspected by the installer prior to installation to ensure no
damage occurred in transit and a damaged part is not used. If any damage occurred in transit,
AquaCreekProducts,LLCmustbenotiedwithinthreedaysofreceiptofunit.
Proper installation cannot be overstressed, as an improper installation voids Aqua Creek’s
warrantyandmayaffectthesafetyoftheuser.
READ CAREFULLY
1

Copyright © 2019 Aqua Creek Products All Rights Reserved Revised 8/22/19
IMPORTANT SAFETY INSTRUCTIONS
  Wheninstallingandusingthiselectricalappliance,basicprecautionsshouldalwaysbe 
  followed,includingthefollowing:
READ ALL INSTRUCTIONS BEFORE USING
WARNING - To reduce the risk of injury, do not permit children to use this product unless they are closely
supervised at all times.
Thisapplianceisnotintendedforusebypersons(includingchildren)withreducedphysical,sensoryor
mentalcapabilities,orlackofexperienceandknowledge,unlesstheyhavebeengivensupervisionor
instruction concerning use of the appliance by a person responsible for their safety.
Awireconnectorisprovidedontheunittoconnectaminimum8AWG(8.4mm2) solid copper conductor
betweenthisunitandthemeansforlocalequipotentialbonding.
Checktheunitperiodicallyforsignsofdeterioration:Keepallnuts,boltsandscrewstighttobesurethe
liftisinsafeworkingcondition.
SAVE THESE INSTRUCTIONS
AfxsuppliedADAPOOL/SPALIFTsigninalocationvisiblefromtheliftatalltimes.
Rechargeable batteries are to be removed from the appliance before being charged. Batteries are to be
insertedwiththecorrectpolarity.Iftheapplianceistobestoredunusedforalongperiodoftime,the
batteries should be removed. The supply terminals are not to be short-circuited.
REDUCE THE RISK OF DROWNING!
Supervise children at all times.
No jumping or diving from the lift.
Seatmaybehot,usecautionwhenentering.
Keepcoveredwhennotinuse.Inspectandcleanbeforeuse.
INDOOR BATTERY CHARGER:
AMPERAGE = 0.65 FREQUENCY = 60
24 VOLT BATTERY
AMPERAGE = 8 IP RATING = IPX5
Spa Lift Ultra
2

Copyright © 2019 Aqua Creek Products All Rights Reserved Revised 8/22/19
5
3
1
4
2
Spa Lift Ultra
Spa Lift Ultra Components
Table of Contents
PAGE DESCRIPTION PAGE DESCRIPTION
3 Spa Lift Ultra Components 9 Pinch Point Locations
4 Anchor Installation 10 Proper care
5-6 Installation and Assembly 11 Spa Lift Ultra Parts List
7 Legrest Installation Instructions 12 Warranty
8 Basic Troubleshooting
1. Spa Lift Ultra
2. 24 Volt Battery
3. Hand Remote
4. Safety Belt
5. Hardwarebagwithanchorinserts&
anti-seize(iforderedw/anchor)
NOTE:Forwooddeckapplicationsreferto
Wood Deck Anchor Manual (F-107UEWDA)
3

Copyright © 2019 Aqua Creek Products All Rights Reserved Revised 8/22/19
Anchor Installation
Before installing the lift, determine where to place the lift on the deck. Locate
the lift as close to the pool/spa as possible to ensure that the seat arm clears the
pool/spa wall. As shown in FIGURE 1 below, the lift must be a minimum of 10”
from the front anchor holes to the pool/spa wall. Also, allow enough room for
the seat arm to swing around away from the pool/spa. Refer to the specications
for lift dimensions.
Youwillneed:
• Hammer
• 11/8”MasonryBit
• Drill
• Marker/Chalk
1.Iforderedwithlift,theSpaLiftUltraisshippedwiththree(3)8inchanchorinserts.Makeamarkonthedeck
withamarkerorchalkateachanchorlocation.
2.Usingthe11/8inchmasonrybit,drillaholeintheconcretedecktoadepthof81/2inchesateachofthe
threeanchorlocations.Theholesmustbedrilledperpendiculartothedeckortheboltswillnotthreadintothe
anchors. Once the holes have been drilled to the proper depth, clean all debris out of the anchor holes.
3.FilleachholehalffullwithHiltiTM brand HIT RE-500-SD or SimpsonTM brand SET-XP, or equivalent. Thread a
1/2inchhexboltintoeachanchorandtheninserttheanchorintothehole,twistingasyougo,untilltheanchor
insertisushwiththedeck.Cleanoffanyexcessepoxyfromaroundtheholeandmakesurenottogetany
epoxyonthe1/2inchthreads.
4.Bondtheanchoraccordingtolocalcoderequirementsusingthebondingscrewonthebottomofoneofthe
anchorinserts.ReferencetheNationalElectricCode(NEC)Article680.26forspecicsonbonding.
3'-6"
3'-6"
4"
(MIN)
10.75"
10.75"
10.75"
10"
(MIN)
10"
(3)
1" x 8" ANCHOR INSERTS
1"
ANCHOR INSERTS
(6" MIN. EMBED.)
3'-6" SQ. x 10" DEEP
CONC. FTG. W/ 5-#5
E.W., TOP & BOTT.
(2500 PSI)
EPOXY TOP MATT TO EXISTING SLAB
(4" MIN. EMBED, 3-SIDES)
POOL/SPA
WALL
POOL/SPA
WALL
FIGURE 1 4

Copyright © 2019 Aqua Creek Products All Rights Reserved Revised 8/22/19
BASE WELDMENT
MAST ASSEMBLY
3/8" NYLOCK
NUT (4)
3/8" FLAT
WASHER (4)
FIGURE 3
LIFTING ARM
MAST ASSEMBLY
1/2" X 3"
SHOULDER BOLT
3/8" NYLOCK
3/8" FLAT WASHER
LOWER ATTACHMENT
POINT
ACTUATOR
MOUNTING
TABS
FIGURE 4
3/8" X 1 1/4"
SHOULDER BOLT
5/16" NYLOCK
5/16" FLAT WASHER
5/16" FLAT WASHER
5/16" NYLOCK
3/8" X 2"
SHOULDER BOLT
LIFTING ARM
MAST ASSEMBLY
ACTUATOR
FIGURE 5
Spa Lift Ultra Installation and Assembly
1.Oncetheanchorinsertshavebeeninstalled,thebaseweldmentcannowbesecuredtothedeckusingthe1/2
inchhexboltsandwashers.SeeFIGURE2.
2.Attachthemastassemblytothebase,asshowninFIGURE3,using
the3/8inchnylocknutsandatwashers.Thismayrequiretwopeople.
SPA LIFT
BASE WELDMENT
1/2" X 1 1/2"
HEX BOLT (3)
1/2" FLAT
WASHER (2)
1" X 8" ANCHOR
INSERT (3)
1/2" EXTERNAL
TOOTH WASHER (1)
FIGURE 2
3.Attachtheliftingarm (identiedbythetwoactuatormounting tabsopposedtothecontrolarmwhich has
notabs)tothemastassemblyusingthe1/2inchshoulderboltand3/8inchnylockandatwasher.Besurethe
actuatormountingtabsontheliftingarmarefacingdownward.SeeFIGURE4.
4.Aftertheliftingarmissecuredtothemast,attachtheactuatortothemastandtheliftingarmwiththe3/8inch
shoulderboltsand5/16inchnylocksandatwashersasshowninFIGURE5.Makesuretheactuatorheadfaces
theoppositedirectionofthecontrolbox.Ifrotatedtheotherway,theactuatorheadmighthitthemast.
5

Copyright © 2019 Aqua Creek Products All Rights Reserved Revised 8/22/19
FIGURE 9
Spa Lift Ultra Installation and Assembly
5.Connectthecontrolarmtothemastusingthe1/2inchshoulderboltand3/8inchnylockandatwasher,as
showninFIGURE6.Carefulnottoscratchthecontrolarmontheliftingarmwhileattaching.
6.Connectthechairarmassemblytotheliftingandcontrolarmsusingthe1/2inchshoulderboltsand3/8inch
nylocksandatwashers.Thismayrequiretwopeople.SeeFIGURE7.
1/2" X 2 3/4"
SHOULDER BOLT
3/8" FLAT WASHER
3/8" NYLOCK
CONTROL ARM
LIFTING ARM
MAST ASSEMBLY
ACTUATOR
FIGURE 6
CHAIR ARM
ASSEMBLY
1/2" X 3" SHOULDER
BOLT (2)
3/8" NYLOCK (2)
3/8" FLAT WASHER (2)
FIGURE 7
7.Attachthesafetybelttothechair,asshowninFIGURE8.
8.TheSpaLiftUltraisnowassembledandreadyforuse!Besurethebatteryisfullycharged.FIGURE9shows
completed assembly mounted on a spa deck. NOTE: With the lift fully assembled, run the lift fully out and back
in3-5times,withoutweight,forthelifts“breakin”cycleperiod.
LOOP ON TOP
FOR EASY ACCESS
THREAD THROUGH
SLOTS AND PINCH
TOGETHER TO HOLD
FIGURE 8 6

Copyright © 2019 Aqua Creek Products All Rights Reserved Revised 8/22/19
The Aqua Creek legrest assembly is designed to t under the chair and is installed inside the 2”
square tubing that supports the chair from underneath. To install the legrest;
1. Insert the legrest assembly into the 2 x 2 square tubing that supports the chair until the plastic
insert of the legrest assembly sits ush against the end of the 2 x 2 tube.
2. Using the supplied 1/4”hardware, fasten the legrest assembly to the 2 x 2 tubing using a 5/32”
allen wrench.
Installation Instructions
1/4" FLAT WASHER
1/4" LOCK WASHER
1/4" X 1/2" BUTTON-HEAD
LEGREST ASSEMBLY
LEGREST IN LEGREST OUT
7

Copyright © 2019 Aqua Creek Products All Rights Reserved Revised 8/22/19
Basic Troubleshooting
Problem: The lift won’t move.
Solution:
1. Make sure the battery is properly seated:
You should hear a click when
the battery is properly seated
on the control box or charger.
Click!
NOT Properly Attached:
Note: the white bracket is
in front of the silver clip,
which will not allow for
an electrical connection
Properly Attached:
Note: the white bracket
is behind the silver clip,
holding it securely to
allow for an electrical
connection
Check the ends of the cords for corrosion or
damage. The cord plugs should be recessed
into the outlet. You should feel them pop into
place when they are correctly inserted.
2. Make sure the cords are properly plugged in:
NOT Properly Inserted:
The cord plug is fl ush with
or sticking out of the outlet
Properly Inserted:
The cord plug is recessed
into the outlet
POP!
The Charger is ON
when the green
light is glowing
The Battery is
CHARGING when the
orange light is glowing
When the Battery is
charged the orange
light will stop glowing
4. Make sure the battery is fully charged:3. Check the contact points:
Make sure the contact points of
the control box and the battery
are not damaged or corroded.
If there is corrosion clean with
Scotch-BriteTM pad. Put some
dielectric grease on the contact
points before reattaching the
battery.
Problem: The lift stopped moving over the water and is stuck.
Solution:
1. Press the emergency button
Use a pen or pencil tip and
stick it into the emergency
button on the front of the
control box to retract the lift.
Note:theliftwillnotretract
if the battery is not fully
charged or if the control box
isnotworking.Theemergency
button only overrides the
remote handset.
8

Copyright © 2019 Aqua Creek Products All Rights Reserved Revised 8/22/19
Pinch Point Locations
CAUTION!
PINCH POINT AREAS!
LIFT TO BE STICKERED
ON BOTH SIDES OF ARMS.
9

Copyright © 2019 Aqua Creek Products All Rights Reserved Revised 8/22/19
Proper Care of Pool & Spa Lifts
PROPER CARE NOTES
• Use only fresh water to wash your lift. Do not wash with pool water
• Use only clean, soft, non-abrasive cloths to wipe down your lift
• Do not store lift in pump room or near chemicals
• Do not allow children to play on or around this lift
• When cleaning the lift do not spray water directly on control box or battery
Toremovestainswashaffectedareawithmilddishsoap.Forstubbornspotsandstainstryusingsoftscrub
withsomebriskrubbing.Usewhiteepoxypainttotouchup.Applywaxtonish.
STAIN REMOVAL TIPS:
1. RECHARGETHEBATTERYASOFTENASPOSSIBLE.Thebatterypowerunitisasealedleadacid
batterypack.Frequentrechargeswillprolongthebatterylifeandmaintainahighcoldamperage
capacity. THE BATTERY SHOULD BE STORED ON THE CHARGER WHEN NOT IN USE.
2. Do NOT expose the battery to freezing temperatures.
3. Do NOT expose the battery to prolonged periods of extreme heat or severe cold temperatures.
4. DoNOTexposethebatterytolongperiodsofdirectsunlight.Heatwillshortenyourbatterylife.
Optimumoperatingrangeisbetween5degreesCelsius(40degreesF)and40degreesCelsius
(105 degrees F.)
5. Never drop or bump the battery pack. This may result in loose or damaged internal connections,
and may damage the battery terminals.
We recommend you place this
page next to your charger
BATTERY MAINTENANCE:
PROCEDURE BEFORE
EACH USE
DAILY WEEKLY MONTHLY
Check battery level indicator on control box 
Run the lift through a complete test cycle (fully
extend actuator) to verify it is functioning properly 
Wash lift with fresh water and dry with clean, soft,
non-abrasive cloth 
Recharge battery 
Visually inspect lift for damage, corrosion, and loose
or missing hardware 
Check all contact points for damage and/or corrosion 
Repair, clean and apply dielectric grease to all contact
points 
Thoroughly clean lift frame and apply a liberal coat of
car wax to maintain the lift’s nish 
Check all Warning and Cautionary labels to make sure
they are not faded or worn. Replace as needed. 
10

Copyright © 2019 Aqua Creek Products All Rights Reserved Revised 8/22/19
2
24
25
29
28
17
18
1718
13
16
17
17
15
30
1
12
22
27
26
4
11
21
20
18
17
3
10
9
19
20
23
23
5
6
27 27
20
21
24 25
7
20 21
8
14
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 SLE-100-01 BEARING HOUSING ASSEMBLY 1
2
SLU-200-01 SPA LIFT BASE MAST WELDMENT 1
3
SCT-300-10 SCOUT MOTOR ASSEMBLY 1
4
SLE-400-03 SPA LIFT MAST ASSEMBLY 1
5
SLU-500-00
SPA LIFT ULTRA LIFTING ARM
ASSEMBLY
1
6
SLU-600-00
SPA LIFT ULTRA CONTROL ARM
ASSEMBLY
1
7
REV-700SP-00
REVOLUTION SPA CHAIR ARM
ASSEMBLY
1
8
REVWM-800-00 CHAIR CRADLE WELDMENT 1
9
F-0904CA-A CHAIR ASSEMBLY, 18" WIDE 1
10 F-LRB LEGREST ASSEMBLY, BLUE 1
11 340665-00 ACTUATOR, LINAK, 400MM 1
12 P-920 SHROUD, PLASTIC, SCOUT, BLUE 1
13 SCT-135-01
GUARD, FINGER GUARD, FOR
SCOUT LIFT
2
14 BAJ1-U026-00 BATTERY, LINAK, 24 VOLT 1
15 BH 1-4 X 3-4 BOLT, 316 SS, 1/4-20 X 3/4 HCS 8
16 BH 1-4 X 1 BOLT, 316 SS, 1/4-20 X 1 HCS 7
17 WF 1-4 WASHER, FLAT, 1/4, 316 SS 34
18
NN 1-4 NUT, 316 SS, NYLOCK, 1/4"-20 19
19
BH 5-16 X 4 1-2 BOLT, 316 SS, 5/16-18 X 4 1/2 HCS 1
20 WF 5-16 WASHER, FLAT, 5/16, 316 SS 5
21 NN 5-16 NUT, 316 SS, NYLOCK, 5/16"-18 4
22 BS 3-8 X 1 1-4 18-8
BOLT, 18-8 SS, 3/8 X 1 1/4
SHOULDER, 5/16-18 THREAD
1
23 BS 3-8 X 2 18-8
BOLT, 18-8, 3/8 X 2 SHOULDER,
5/16-18 THREAD
2
24 WF 3-8 WASHER, FLAT, 3/8, 316 SS 8
25 NN 3-8 NUT, 316 SS, NYLOCK, 3/8"-16 8
26 BS 1-2 X 2 3-4 18-8
BOLT, 18-8 SS, 1/2 X 2 3/4
SHOULDER, 3/8-16 THREAD
1
27 BS 1-2 X 3 18-8
BOLT, 18-8 SS, 1/2 X 3 SHOULDER,
3/8-16 THREAD
3
28 WFC 3-4
WASHER, FLAT, 3/4, 304 SS,
CUSTOM
1
29 NN 3-4 NUT, 316 SS, NYLOCK, 3/4"-10 1
30 F-UBC
COVER, UNIVERSAL BATTERY
COVER
1
Spa Lift Ultra
Parts List
ITEM # QTY PART # DESCRIPTION
1 1 SLE-100-01 BEARING HOUSING ASSEMBLY
2 1 SLU-200-01 BASE MAST WELDMENT
3 1 SCT-300-10 MOTOR ASSEMBLY
4 1 SLE-400-03 MAST ASSEMBLY
5 1 SLU-500-00 LIFTING ARM ASSEMBLY
6 1 SLU-600-00 CONTROL ARM ASSEMBLY
7 1 REV-700SP-00 CHAIR ARM ASSEMBLY
8 1 REVWM-800-00 CHAIR CRADLE WELDMENT
9 1 F-0904CA-A 18” CHAIR ASSEMBLY
10 1 F-LRB LEGREST ASSEMBLY
11 1 340665-00 400MM LINAK ACTUATOR
12 1 P-920 PLASTIC SHROUD
13 2 SCT-135-01 FINGER GUARD
14 1 BAJ1-U026-00 24V BATTERY
15 8 BH 1/4 X 3/4 1/4-20 X 3/4 HEX BOLT
ITEM # QTY PART # DESCRIPTION
16 7 BH 1/4 X 1 1/4-20 X 1 HEX BOLT
17 34 WF 1/4 1/4 FLAT WASHER
18 19 NN 1/4 1/4-20 NYLOCK NUT
19 1 BH 5/16 X 4 1/2 5/16-18 X 4 1/2 HEX BOLT
20 5 WF 5/16 5/16 FLAT WASHER
21 4 NN 5/16 5/16-18 NYLOCK NUT
22 1 BS 3/8 X 1 1/4 18-8 3/8 X 1 1/4 SHOULDER BOLT
23 2 BS 3/8 X 2 18-8 3/8 X 2 SHOULDER BOLT
24 8 WF 3/8 3/8 FLAT WASHER
25 8 NN 3/8 3/8-16 NYLOCK NUT
26 1 BS 1/2 X 2 3/4 18-8 1/2 X 2 3/4 SHOULDER BOLT
27 3 BS 1/2 X 3 18-8 1/2 X 3 SHOULDER BOLT
28 1 WFC 3/4 3/4 CUSTOM WASHER
29 1 NN 3/4 3/4-10 NYLOCK NUT
30 1 F-UBC BATTERY/CONTROL BOX COVER
We recommend you place this
page next to your charger
11

Copyright © 2019 Aqua Creek Products All Rights Reserved Revised 8/22/19
Revised_9.14.2017
AQUA CREEK PRODUCTS, LLC LIMITED FIVE (5) YEAR WARRANTY:
ELITE & ULTRA SPA LIFTS
(ITEM #’s F-006SLE, F-005SLU)
Aqua Creek Products, LLC (a.k.a. Aqua Creek) warrants to the original end user purchaser that products manufactured by Aqua
Creek, when properly installed in accordance with assembly and installation instructions, and properly used and maintained, shall be
free from defects in material and workmanship for a period of five (5) years from the date of original purchase, provided that Aqua
Creek receives prompt notice in writing of any defect or failure and satisfactory proof thereof, with the following exception(s):
Exceptions:
All electrical components, including the linear actuator shall have the following warranty period:
oYear 1-2: 100% Coverage
oYear 3: 60% Coverage (Customer is responsible for 40% of replacement cost)
oYear 4: 50% Coverage (Customer is responsible for 50% of replacement cost)
oYear 5: 40% Coverage (Customer is responsible for 60% of replacement cost)
Hydraulic actuators and mesh slings shall have a warranty period of one (1) year from the date of original purchase.
Powder coat finish scratches, scrapes, corrosion, or dents from customers normal use, negligence, or abuse
This warranty specifically excludes reimbursement for labor to remove, repair, or install the product and any shipping charges.
These warranties do not cover any damages due to accident, force majeure, act of nature, misuse, abuse, negligence or failure to
properly maintain any products, or normal wear and tear from day to day operations. In the event that any products are altered,
repaired, or improperly installed or improperly used by anyone without the prior written approval by Aqua Creek, all warranties are
void. IMPORTANT: AMOUNT OF WEIGHT PLACED ON LIFT SHALL NOT EXCEED THE RATED LIFTING CAPACITY FOR THE LIFT. NEVER
OPERATE THE LIFT UNDER LOAD IN A DRY POOL (WITH NO WATER IN THE POOL). It is the responsibility of the lift owner to verify
the weight of the patron for warranty claim purposes and to ensure that the lift is not overloaded. Non-payment for product to
Aqua Creek may void warranty.
To initiate a warranty claim, the owner of an Aqua Creek product must provide the place of purchase, in writing, with a full
description of the product, its serial number, the dates of purchase and installation, and the exact nature of the defect. Within thirty
(30) days after receipt of a written warranty claim by Aqua Creek, and barring any unforeseen delays, the place of purchase will be
notified of Aqua Creek’s decision regarding the claim.
If requested by Aqua Creek, any defective product must be returned, freight prepaid by customer, to Aqua Creek’s designated
factory location or duly appointed distributor for inspection and/or repair. Aqua Creek will, at its option, repair or replace the failed
or defective item, and deliver the repaired product or replacement to the customer. All freight charges are the responsibility of the
customer. Products returned to Aqua Creek for which Aqua Creek provides replacement under this limited warranty shall become
the property of Aqua Creek. A new warranty period shall NOT be established for the repaired or replaced products. Such products
shall remain under warranty only for the remainder of the original warranty period on the original products purchased.
This written limited warranty constitutes the final, complete and exclusive statement of warranty terms. No person or organization
is authorized to make any other specific or implied warranties or representations on behalf of Aqua Creek.
THE WARRANTIES SET FORTH HEREIN ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, WHICH ARE HEREBY DISCLAIMED AND EXCLUDED,
INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE.
THE SOLE AND EXCLUSIVE REMEDIES FOR BREACH OF ANY AND ALL WARRANTIES WITH RESPECT TO THE PRODUCTS SHALL BE LIMITED TO REPAIR OR
REPLACEMENT AT AQUA CREEK’S DESIGNATED FACTORY LOCATION, OR DULY APPOINTED DISTRIBUTOR, OR IN PLACE AT AQUA CREEK’S OPTION. IN NO EVENT
SHALL AQUA CREEK’S LIABILITY EXCEED THE ENTIRE AMOUNT PAID TO AQUA CREEK BY THE ORIGINAL PURCHASER FOR THE FAILED OR DEFECTIVE PRODUCT.
IN NO EVENT SHALL AQUA CREEK PRODUCTS, LLC BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, INDIRECT, PUNITIVE OR EXEMPLARY DAMAGES OR
LOST PROFITS FROM ANY BREACH OF THIS LIMITED WARRANTY OR OTHERWISE.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH MAY VARY FROM STATE TO STATE. SOME STATES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, SO SOME OF THE ABOVE LIMITATIONS OR EXCLUSIONS MAY
NOT APPLY TO YOU.
Aqua Creek Products, LLC
9889 Garrymore Lane
Missoula, MT 59808
Toll Free: [phone]
Local/Intnl: [phone]
www.aquacreek.com
12