Aqua Luxe Poseidon User manual

OWNER’S MANUAL

1
QUICK REFERENCE
To assist you with the installation, maintenance, and
potential future service of your new Aqua Luxe brand
spa, please ll out the following information and keep
it on hand for future reference.
Spa Information
Model:
Serial Number:
Dealership:
Dealer’s Phone Number:
Date Purchased:
Date Installed:
Contractor Information
General
1. Name:
Telephone:
2. Name:
Telephone:
Electrician
1. Name:
Telephone:
2. Name:
Telephone:
Concrete, Decking, and Masonry
1. Name:
Telephone:
2. Name:
Telephone:
Landscaping
1. Name:
Telephone:
2. Name:
Telephone:

2
TABLE OF CONTENTS
Quick Reference:
Table of Contents:
Important Overview:
Safety Instructions:
Getting to Know Your Spa:
Equipment Compartment:
Filling Your Spa:
Touch Control Panel:
Color Control Panel:
Jets:
Water Care and Chemistry:
Spa Maintenance:
Installation & Delivery
GFCI Setup
Wiring Diagram:
Troubleshooting Guide:
Display and Error Messages:
1
2
3
4
7
8
9
10
20
24
25
27
32
38
39
40
41

3
IMPORTANT OVERVIEW
Congratulations on your purchase of a Aqua Luxe hot tub†.
NOTE: In this document, the terms “Spa” and “Hot Tub” are
used interchangeably.Take a moment to read this manual carefully.
Following the instructions in this manual will ensure the safe and
smooth operation of your new spa.
Carefully read this Owner’s Manual before you install your spa.
Your Aqua Luxe Limited Warranty may be voided if damage
is caused by failure to install, maintain, and operate your spa in
accordance with the recommendations contained in this Owner’s
Manual or any other printed instruction, notice or bulletin from
Aqua Luxe. Your spa’s serial number is located both on the base
under the equipment door and the Manufacturing ID Label
located inside the equipment compartment of your spa.
For the safety of all those who utilize your spa and its surroundings,
please make sure your spa and any adjoining installations,including
the electrical hook-up, are completed according to codes of and
only after acquiring any necessary approvals and permits from your
local, state/provincial, and/or national government.Follow all local,
state, and natonal safety and wiring rules. Some jurisdictions
require certain fencing and/or self-closing and self-latching gates
to prevent accidental drowning in a pool or spa. Your spa cover
comes with a locking system that meets the ASTM F1346-91
Standard for Safety Covers, which when properly used, may satisfy
certain fencing and gating requirements.Your spa meets or exceeds
all requirements of the Virginia Graeme Baker Pool and Spa Safety
Act. Your spa has been tested and either meets or exceeds the UL-
1563 portable spa standard.
U.S. Patents: 7,908,684, 8,661,576, 8,881,321,
8,689,370, 8,869,469, 5,754,989, 5,987,663,
6,000,073, 6,092,246, 6,256,805, 6,543,067.
New Zealand Patents: 555112, 334,093
Australia Patents: 737,335
Canada Patents: 2,588,884, 2,260,237, 2,915,184
Other patents pending worldwide
† Aqua Luxe spas are available in the following models:
Triton, Poseidon, Venus, Aurora, Vesta, Terra
Aqua Luxe reserves the right to change features,
specications & design without notication and
without incurring any obligation.

4
IMPORTANT SAFETY INSTRUCTIONS
Save these instructions
Safety Instructions
When installing and using this electrical equipment, basic safety
precautions should always be followed, including the following:
1. Read and follow all instructions:
2. WARNING: To reduce the risk of injury, do not permit
children to use this product unless closely supervised at all
times.
3. As per UL requirements (U.S.),a wire connector is provided on
this unit to connect a minimum No. 8 AWG (8.4mm2) solid
copper conductor between this unit and any metal equipment,
metal enclosures of electrical equipment, metal water pipe, or
conduit within 5 feet (1.5m) of the unit.
4. WARNING: For products provided with a cord-
connected, ground-fault circuit-interrupter, the GFCI must
be tested before each use.If the GFCI fails to operate properly,
disconnect the power until the fault has been identied and
corrected.
5. DANGER: Risk of Accidental Drowning. Extreme
caution must be exercised to prevent unauthorized access by
children. To avoid accidents, ensure that children cannot use
this spa unless they are supervised at all times.
6. DANGER: Risk of Injury. e suction ttings in the
spa are sized to match the specic water ow created by the
pump. Should the need arise to replace the suction ttings or
the pump, be sure that the ow rates are compatible. Never
operate the spa if the suction ttings are broken or missing.
Do not replace a suction tting with one rated less than the
ow rate marked on the original suction tting.
7. DANGER: Risk of Electric Shock. As per UL
requirements (U.S.), install spa at least 5 feet (1.5m) from all
metal surfaces. A spa may be installed within 5 feet (1.5m) of
metal surfaces if each metal surface is permanently connected
by a minimum of No. 8 AWG (8.4mm2) solid copper
conductor to the wire connector on the terminal box that is
provided for this purpose.
8. DANGER: Risk of Electric Shock. Do not permit any
electrical appliances, such as a light, telephone, radio, or
television within 5 feet (1.5m) of the spa. ese units DO
NOT have an integral ground fault circuit interrupter. e
installation of an integral ground fault circuit interrupter
MUST be completed by a qualied Electrician and must meet
all applicable electrical codes.
9. For Cord-Connected units:
a. Replace damaged cord immediately.
b. Do not bury cord.
c. Connect to grounded, grounding-type receptacle only.
10. WARNING: To Reduce the Risk of Injury:
a. Water temperature in a spa should never exceed 104˚F
(40 ˚ C). Water temperatures between 100˚ F (38˚C) and
104˚F (40˚C) are considered safe for a healthy adult.Water
temperature in excess of 104˚ F (40˚ C) may be harmful
to your health. Lower temperatures are recommended for
young children and/or when spa use exceeds 10 minutes.
b. High temperatures could have a potential for causing fetal
damage during pregnancy. Pregnant women or women
that could be pregnant should consult a physician and
possibly limit spa usage when temperatures are in excess
of 100˚ F (38˚ C).
c. Before entering the spa, measure the water temperature
with an accurate thermometer since tolerances of water
temperature regulating devices may vary.
d. Use of alcohol, drugs, or medication before or during spa
use may lead to unconsciousness with the possibility of
drowning.
e. Persons suering from obesity or a medical history of
heart disease, low or high blood pressure, circulatory
system problems, and/or diabetes should consult a
physician before using a spa.
f. Persons using medication should consult a physician
before using a spa. Some medications may induce
drowsiness while other medication may aect heart rate,
blood pressure, and/or circulation.
11. WARNING: PEOPLE WITH INFECTIOUS
DISEASES SHOULD NOT USE A SPA OR HOT TUB.
12. WARNING: TO AVOID INJURY, EXERCISE
CARE WHEN ENTERING OR EXITING THE SPA
OR HOT TUB. NEVER DIVE OR JUMP INTO THE
SPA.
13. WARNING: DO NOT USE A SPA OR HOT
TUB IMMEDIATELY FOLLOWING STRENUOUS
EXERCISE.
14. WARNING: PROLONGED IMMERSION IN A
SPA OR HOT TUB MAY BE HARMFUL TO YOUR
HEALTH.
15. CAUTION: MAINTAIN WATER CHEMISTRY
IN ACCORDANCE WITH MANUFACTURER’S
INSTRUCTION.
16. CAUTION: ADEQUATE DRAINAGE MUST BE
PROVIDED IF THE EQUIPMENT IS TO BE
INSTALLED IN A SPAVAULT OR BELOW GROUND
LEVEL.
17. WARNING: Risk of Fatal Hyperthermia.
Hyperthermia occurs when the internal temperature of the
body reaches a level several degrees above the normal body
temperature of 98.6˚ F (37˚ C).e symptoms of Hyperthermia
include dizziness, lethargy, drowsiness, and fainting.e
use of alcohol, drugs, and/or medication can greatly
increase the risk of fatal Hyperthermia .

5
e eects of Hyperthermia include:
a. Unawareness of impending hazard
b. Failure to perceive heat
c. Failure to recognize the need to exit the spa
d. Physical inability to exit the spa
e. Fetal damage in pregnant women
f. Unconsciousness and danger of drowning
18. WARNING: Risk of Children Drowning. Your spa
cover is not rated as a safety cover. It is suggested to always
keep the spa cover securely fastened when not in use.is will
discourage children from attempting to enter the spa
unsupervised. If cover is damaged it should be replaced.
19. WARNING: Risk of Drowning. Use caution when
bathing alone. Overexposure may cause nausea, dizziness, and
fainting.
20. CAUTION: Risk of Injury. Young children should
always be supervised so that they do not play in or around the
spa.
21. WARNING: Keep all glassware and other breakable
objects away from the spa area.
22. WARNING: Risk of Injury: Short-term inhalation of
high concentrations of ozone and long-term inhalation of low
concentrations of ozone can cause serious physiological eects.
23. CAUTION: Unauthorized Access. Secure the spa area
against unauthorized access. Make sure all spa barriers (fences,
enclosures, etc.) meet all applicable national and local codes.
Keep spa cover on and locked when it is not being used.
24. CAUTION: Risk of Damage to Spa or Equipment. By
performing maintenance as described in this manual, the
chance of damage to your spa and its equipment will be
reduced. Never block the air vents that lead to the spa’s
equipment compartment, doing so may cause the spa to
overheat.
25. WARNING: Risk of Electric Shock or Death. Do not
operate spa during severe weather conditions (e.g. electrical
storms, tornadoes, etc.).
26. CAUTION: Non-Approved Accessories. Using
accessories not approved by Bullfrog International, LC could
void your warranty or cause other problems. Please consult
your authorized Aqua Luxe dealer.
27. CAUTION: Spa Location. Locate your spa on a
foundation that can support the maximum lled weight of
your spa along with the weight of all the occupants using the
spa (see Site Selection and Preparation). Also, locate your spa
in an environment that can withstand repeated exposure to
water and the possibility of a major spill.
28. CAUTION: Power cords must be replaced only with
a special cord assembly available from the Manufacturer, its
Service Agent, or similarly qualied persons in order to avoid
a hazard.
29. WARNING: is appliance is not intended for use by
young children or unhealthy persons without supervision.
30. WARNING: Before obtaining access to supply
terminals, all supply circuits must be disconnected.
31. WARNING: Risk of Injury or Accidental Drowning:
Do not use spa without lters,lter plate,and lter SnapCaps™
installed; these parts serve as a barrier against bodily
entrapment against the lter suction tting(s).
32. CAUTION: Test the GFCI or RCD ( Residual
Current Device) before each use of the spa.
Additional Instructions
(Canadian Installations Only):
33. A green-colored terminal or a terminal marked G, GR,
Ground, Grounding or the international grounding symbol
is located inside the supply terminal box or compartment.
To reduce the risk of electric shock, this terminal must be
connected to the grounding means provided in the electric
supply service panel with a continuous copper wire equivalent
in size to the circuit conductors supplying this equipment.
34. At least two lugs marked “BONDING LUGS” are provided
on the external surface or on the inside of the supply terminal
box or compartment. To reduce the risk of electric shock,
connect the local common bonding grid in the area of the spa
or hot tub to these terminals with an insulated or bare copper
conductor not smaller than No. 6 AWG.
35. All eld-installed metal components such as rails, ladders,
drains, or other similar hardware located within 10 feet
(3m) of the spa or hot tub must be bonded to the equipment
grounding bus with copper conductors not smaller than No.
6 AWG.
36. WARNING: Risk to Infants, Elderly, and Women
Planning or Experiencing Pregnancy. Please consult your
physician if the above applies to you or anyone using the spa

6
Warning Signs (North
America)
Included with the spa is a warning sign to inform users
and guest of the risks involved with using a spa. is
sign is suitable for indoor and outdoor use. It should be
placed in a noticeable place adjacent to the spa.*
* Final warning sticker is included with spa for installation by owner.
THIS MARKING IS TO BE REMOVED ONLY BY THE OWNER AFTER SAFETY SIGN IS INSTALLED
69.1-S
REDUCE THE RISK OF ELECTROCUTION
1. NEVER PLACE AN ELECTRIC APPLIANCE WITHIN 5FEET OF SPA
REDUCE THE RISK OF CHILD DROWNING
1. SUPERVISE CHILDREN AT ALL TIMES.
2. ATTACH SPA COVER AFTER EACH USE.
REDUCE THE RISK OF OVERHEATING
1. CHECK WITH A DOCTOR BEFORE EACH USE IF PREGNANT, DIABETIC, IN POOR HEALTH, OR UNDERMEDICALCARE.
2. EXITIMMEDIATLY IF UNCOMFORTABLE,DIZZY, OR SLEEPY. SPA HEAT CAN CAUSE HYPERTHERMIA AND UNCONSCIOUSNESS
3. SPA HEAT IN CONJUNCTION WITH ALCOHOL,DRUGS, OR MEDICATION CAN CAUSE UNCONSCIOUSNESS.
WHEN PREGNANT, SOAKING IN HOT WATER FOR LONGPERIODS CAN HARM YOUR FETUS.
MEASURE WATER TEMPERATURE BEFORE ENTERING.
1. DO NOT ENTER SPA IF WATER IS HOTTER THAN 100˚F (38˚C)
2. DONOT STAY IN SPA FORLONGER THAN 10MINUTES.
70.1-0
REDUCE THE RISK OF ELECTROCUTION
1. NEVER PLACE AN ELECTRIC APPLIANCE WITHIN 5 FEET OF SPA
REDUCE THE RISK OF CHILD DROWNING
1. SUPERVISE CHILDREN AT ALL TIMES.
2. ATTACH SPA COVER AFTER EACH USE.
REDUCE THE RISK OF OVERHEATING
1. CHECK WITH A DOCTOR BEFORE EACH USE IF PREGNANT, DIABETIC, IN POOR HEALTH, OR UNDER MEDICAL CARE.
2. EXIT IMMEDIATLY IF UNCOMFORTABLE, DIZZY, OR SLEEPY. SPA HEAT CAN CAUSE HYPERTHERMIA AND UNCONSCIOUSNESS
3. SPA HEAT IN CONJUNCTION WITH ALCOHOL, DRUGS, OR MEDICATION CAN CAUSE UNCONSCIOUSNESS.
WHEN PREGNANT, SOAKING IN HOT WATER FOR LONG PERIODS CAN HARM YOUR FETUS.
MEASURE WATER TEMPERATURE BEFORE ENTERING.
1. DO NOT ENTER SPA IF WATER IS HOTTER THAN 100˚F (38˚C)
2. DO NOT STAY IN SPA FOR LONGER THAN 10 MINUTES.
REDUCE THE RISK OF ELECTROCUTION
1. NEVER PLACE AN ELECTRIC APPLIANCE WITHIN 5 FEET OF SPA
2. DO NOT INSTALL UNDER SPA SKIRT OR WITHIN AN ENCLOSURE THAT WOULD RESTRICT VENTILATION.
3. IF BLOWER IS INCLUDED, INSTALL AT LEAST 1 FOOT ABOVE MAXIMUM WATER LEVEL.
REDUCE THE RISK OF CHILD DROWNING
1. SUPERVISE CHILDREN AT ALL TIMES.
2. ATTACH SPA COVER AFTER EACH USE.
3. INSTALL A SUCTION GUARD WITH MARKED FLOW RATE NO LESS THAN ____GPM TO AVOID HAIR & BODY ENTRAPMENT.
REDUCE THE RISK OF OVERHEATING
1. CHECK WITH A DOCTOR BEFORE EACH USE IF PREGNANT, DIABETIC, IN POOR HEALTH, OR UNDER MEDICAL CARE.
2. EXIT IMMEDIATLY IF UNCOMFORTABLE, DIZZY, OR SLEEPY. SPA HEAT CAN CAUSE HYPERTHERMIA AND UNCONSCIOUSNESS
3. SPA HEAT IN CONJUNCTION WITH ALCOHOL, DRUGS, OR MEDICATION CAN CAUSE UNCONSCIOUSNESS.
WHEN PREGNANT, SOAKING IN HOT WATER FOR LONG PERIODS CAN HARM YOUR FETUS.
MEASURE WATER TEMPERATURE BEFORE ENTERING.
1. DO NOT ENTER SPA IF WATER IS HOTTER THAN 100˚F (38˚C) 2. DO NOT STAY IN SPA FOR LONGER THAN 10 MINUTES. 70.2-E

7
GETTING TO KNOW YOUR SPA
Spa Overview
[Triton Pictured]

8
EQUIPMENT COMPARTMENT

9
FILLING YOUR SPA
WARNING: An empty spa (spa without water in it) must not
be left exposed to sunlight as shell damage may occur. Once the
spa is unwrapped, ll spa with water immediately or shade the spa
with cover or wrapping to prevent direct exposure to sunlight.
IMPORTANT: Do not turn power on to the spa without
water in the spa. Serious damage to the pump and heater may
occur.
WARNING: Make sure power is o to your spa prior to
following spa lling procedure. Failure to do so may result in
serious injury.
Step 1: Remove lter cover by lifting until snap ttings release.
Step 2: Remove a lter by unscrewing in a counter-clockwise
direction.
Step 3: Place garden hose directly inside the plumbing below
the removed lter.
Step 4: Fill to the water level indicator line located on the right
side of the grill on the face of the lter plate assembly.
Step 5: Fill spa until water level reaches the indicator line at
right of the lter grill. Reinstall the lter and lter cover.
IMPORTANT: Never ll the spa with soft water unless an
appropriate mineral supplement is immediately added (see your
authorized Aqua Luxe Dealer). If your water is extremely hard, it
is preferable to either dilute the water’s hardness by blending the
water with water from a water softener, or by the addition of a
special water softening chemical (see your authorized Aqua Luxe
Dealer).
Step 6: Check for leaks: After the spa is lled, check all ttings
and equipment in equipment compartment for signs of leakage
before turning on the spa. Turn on pump(s), once again, check
for leakage. If a leak is detected, tighten the tting by hand. If the
leak persists contact your authorized Aqua Luxe Dealer.
Step 7: Install Cover: e spa cover comes with tie down
straps and locking hardware that attaches the cover to the spa or
decking. If your dealer did not install the cover, refer to the Cover
Installation Instructions included with the cover.
Cover locks are an essential component for compliance with the
ASTM F1346-91 safety standard for spa covers.
Note: e spa cover is an important part of maintaining spa
water at the desired temperature. When spa is not in use, place
the cover over the spa and attach tie down straps to the locking
hardware.
Control System
IMPORTANT: Your Aqua Luxe spa is equipped with one
of 2 types of control pads. Locate the control system on your spa
by matching it with the photo provided under each control panel
section and follow the specic instructions for operation of your
specic control system.

10
in.k 1000 TOUCH CONTROL
1
Quick Reference Card
Please consult your spa user manual for complete info on the features of your spa system.
in.k1000
touch screen keypad
No buttons, keys and overlays! Mode and function selection wheels, all-on or all-off one touch activation key of last
used settings, interactive display icons and on-screen messages are all elements of the in.k1000 user interface
designed to let spa users interact intuitively with their spa and its value-added accessories.
notification icons
Notification icons at the top right-hand side of the screen show the status of connected value-added accessories.
spas functions
Quick and easy step-by-step instructions to control the main functions and
to configure system settings of your spa from its in.k1000 main spa keypad.
in.clear
system is on
in.clear
system is idle
in.clear
system is off
in.stream 2 audio
system is on
in.stream 2 audio
system is off
in.mix
is installed
system is connected
to wifi
system is not
connected to wifi
All-on or all-off key
(one touch activation)
direct to function
selection wheel
(settings and
additional options)
on-screen
system message
and reminder
interactive display icons
(main spa functions)
mode selection
wheel (settings
and accessories)
turn keypad on
3 minutes after the last pump is turned off, the
screen will shut off if there is no touch activity.
Touch the screen to turn on the keypad.
Then follow the instructions on the screen to
access the main screen.
all-on, all-off target key
in.k1000 features an all-on or all-off one touch
activation key. When pressed, it tops or starts all
working components and accessories at once.
From the home page, you can access the
following modes:
• audio (with in.stream 2 connected)
• spa
• settings
To select a function, slide the left wheel up or
down until the desired icon menu is highlighted
in the middle.
1
Quick Reference Card
Please consult your spa user manual for complete info on the features of your spa system.
in.k1000
touch screen keypad
No buttons, keys and overlays! Mode and function selection wheels, all-on or all-off one touch activation key of last
used settings, interactive display icons and on-screen messages are all elements of the in.k1000 user interface
designed to let spa users interact intuitively with their spa and its value-added accessories.
notification icons
Notification icons at the top right-hand side of the screen show the status of connected value-added accessories.
spas functions
Quick and easy step-by-step instructions to control the main functions and
to configure system settings of your spa from its in.k1000 main spa keypad.
in.clear
system is on
in.clear
system is idle
in.clear
system is off
in.stream 2 audio
system is on
in.stream 2 audio
system is off
in.mix
is installed
system is connected
to wifi
system is not
connected to wifi
All-on or all-off key
(one touch activation)
direct to function
selection wheel
(settings and
additional options)
on-screen
system message
and reminder
interactive display icons
(main spa functions)
mode selection
wheel (settings
and accessories)
turn keypad on
3 minutes after the last pump is turned off, the
screen will shut off if there is no touch activity.
Touch the screen to turn on the keypad.
Then follow the instructions on the screen to
access the main screen.
all-on, all-off target key
in.k1000 features an all-on or all-off one touch
activation key. When pressed, it tops or starts all
working components and accessories at once.
From the home page, you can access the
following modes:
• audio (with in.stream 2 connected)
• spa
• settings
To select a function, slide the left wheel up or
down until the desired icon menu is highlighted
in the middle.

11
1
Quick Reference Card
Please consult your spa user manual for complete info on the features of your spa system.
in.k1000
touch screen keypad
No buttons, keys and overlays! Mode and function selection wheels, all-on or all-off one touch activation key of last
used settings, interactive display icons and on-screen messages are all elements of the in.k1000 user interface
designed to let spa users interact intuitively with their spa and its value-added accessories.
notification icons
Notification icons at the top right-hand side of the screen show the status of connected value-added accessories.
spas functions
Quick and easy step-by-step instructions to control the main functions and
to configure system settings of your spa from its in.k1000 main spa keypad.
in.clear
system is on
in.clear
system is idle
in.clear
system is off
in.stream 2 audio
system is on
in.stream 2 audio
system is off
in.mix
is installed
system is connected
to wifi
system is not
connected to wifi
All-on or all-off key
(one touch activation)
direct to function
selection wheel
(settings and
additional options)
on-screen
system message
and reminder
interactive display icons
(main spa functions)
mode selection
wheel (settings
and accessories)
turn keypad on
3 minutes after the last pump is turned off, the
screen will shut off if there is no touch activity.
Touch the screen to turn on the keypad.
Then follow the instructions on the screen to
access the main screen.
all-on, all-off target key
in.k1000 features an all-on or all-off one touch
activation key. When pressed, it tops or starts all
working components and accessories at once.
From the home page, you can access the
following modes:
• audio (with in.stream 2 connected)
• spa
• settings
To select a function, slide the left wheel up or
down until the desired icon menu is highlighted
in the middle.

12
1
direct to function
selection wheel:
water care -
maintenance -
date & time -
keypad -
electrical config -
wifi -
about -
spa mode
spa mode
To select the spa mode, slide the left wheel up
or down until the spa icon is highlighted in the
middle.
The home page will display its equipment
start or stop keys, up and down buttons, water
temperature, messages and quick access to
display options:
• display orientation
• display contrast
To select an option, slide the right wheel up or
down until the desire icon menu is highlighted in
the middle.
display orientation
To modify the display orientation settings, slide
the right wheel until the display orientation icon is
highlighted in the middle.
Simply touch the line of the orientation you want
to select.
start or stop accessories
To start or stop an accessory (pump, blower,
light), touch the associated icon. Icons will
become animated when their accessory is turn
on, and animation will stop when turn off.
Icons on the screen will reflect the speed or state
of the devices running on your spa. When an
accessory has more than one speeds press the
button until it reaches the desired speed.
display contrast
To modify the display contrast settings, slide
the right wheel until the display contrast icon is
highlighted in the middle.
Simply touch the line of the contrast you want
to select.
water temperature
The temperature at the bottom of the screen
shows the current water temperature. Use the Up
and Down icon to set the desired temperature.
The set point will appear in blue. After 3 seconds
without any changes to the set temperature value,
the current water temperature will reappear.
When the set value is lower than the current
temperature Cooling to xx.x will appear below.
When the set value is higher than the current
temperature, Heating to xx.x will be indicated
under the value. Normally there is a short delay
before the heating starts, during which Heating
Suspended is indicated under the value.
list of featured items
mode selection
wheel:
settings icon
settings
You can use the Settings mode to manage settings of your spa system.
To select the settings mode, slide the left wheel up or down until the settings icon menu is highlighted in
the middle.
In the Settings page you can access the following:
• water care • electrical configuration
• maintenance • wifi
• date & time • miscellaneous
• keypad • about
To select an item, slide the right wheel until the desired icon is highlighted in the middle or press on the
menu name.
sleep
Press key to go directly into the sleep mode. In
sleep mode, water splashing on the keypad can't
inadvertently start/stop a pump.

13
1
direct to function
selection wheel:
water care -
maintenance -
date & time -
keypad -
electrical config -
wifi -
about -
spa mode
spa mode
To select the spa mode, slide the left wheel up
or down until the spa icon is highlighted in the
middle.
The home page will display its equipment
start or stop keys, up and down buttons, water
temperature, messages and quick access to
display options:
• display orientation
• display contrast
To select an option, slide the right wheel up or
down until the desire icon menu is highlighted in
the middle.
display orientation
To modify the display orientation settings, slide
the right wheel until the display orientation icon is
highlighted in the middle.
Simply touch the line of the orientation you want
to select.
start or stop accessories
To start or stop an accessory (pump, blower,
light), touch the associated icon. Icons will
become animated when their accessory is turn
on, and animation will stop when turn off.
Icons on the screen will reflect the speed or state
of the devices running on your spa. When an
accessory has more than one speeds press the
button until it reaches the desired speed.
display contrast
To modify the display contrast settings, slide
the right wheel until the display contrast icon is
highlighted in the middle.
Simply touch the line of the contrast you want
to select.
water temperature
The temperature at the bottom of the screen
shows the current water temperature. Use the Up
and Down icon to set the desired temperature.
The set point will appear in blue. After 3 seconds
without any changes to the set temperature value,
the current water temperature will reappear.
When the set value is lower than the current
temperature Cooling to xx.x will appear below.
When the set value is higher than the current
temperature, Heating to xx.x will be indicated
under the value. Normally there is a short delay
before the heating starts, during which Heating
Suspended is indicated under the value.
list of featured items
mode selection
wheel:
settings icon
settings
You can use the Settings mode to manage settings of your spa system.
To select the settings mode, slide the left wheel up or down until the settings icon menu is highlighted in
the middle.
In the Settings page you can access the following:
• water care • electrical configuration
• maintenance • wifi
• date & time • miscellaneous
• keypad • about
To select an item, slide the right wheel until the desired icon is highlighted in the middle or press on the
menu name.
sleep
Press key to go directly into the sleep mode. In
sleep mode, water splashing on the keypad can't
inadvertently start/stop a pump.

14
1
water care
The Water care page will help you set up your ideal filtration and heating settings.The Water care page
will help you set up your ideal filtration and heating settings. Choose, set or modify one of the
5 suggested modes depending on your needs at any given time.
Away from home
In this mode the
spa will always be in
economy; the set point
will be reduced
by 20° F.
Beginner
The spa will never be
in economy mode
and will be filtering
according to the pack's
low level configuration.
Energy Savings
The spa will be in
economy mode during
the peak hours of
the day and resume
normal mode on
the weekend.
Super Energy
The spa will always
be in economy mode
during peak hours,
every day of the week.
Weekender
The spa will be in
economy mode from
Monday to Friday, and
will run normally on
the weekend.
modifying water care schedules
water care
To modify a Water care category, touch the pen
icon at the right end of the desired water care to
open the selected Water Care menu.
In Economy mode, the set point will be reduced
by 20°F, which means that the heating system
will not be engaged unless the temperature falls to
20°F below the spa's set temperature.
The filtration schedule show on the screen will be
applied to the main filtration pump, most likely
pump 1. If your spa uses a circulation pump
configured to run 24 hours, the screen will show
you the purge setting instead of filtration.
The purges are pre-programmed for a fix number
of minutes, therefore the duration will be set to
N/A on the screen, and only the start time can be
modified.
economy
Touch the Economy tab to change the economy
schedule. You can add economy schedules by
touching the orange line labelled "Add Economy" .
To delete a schedule, touch the garbage can icon
at the right end of the desired line.
You can modify the programmed schedules by
selecting one and adjusting the schedule.
You have several possibilities for the schedule
(Mon-Fri, weekend, every day, or single days).
The schedules will be repeated every week.
The time and duration are set in 30 minute
increments.
purges
Touch the Purge tab to change the purge
settings. You can add purges by touching the
orange line labelled "Add purge time".
To delete a schedule, touch the garbage can icon
at the right end of the desired line.
filter cycles
Touch the Filter cycle tab to change the filter
cycle schedules. You can add filtration schedules
by touching the orange line labelled "Add filter
cycle" .
To delete a schedule, touch the garbage can icon
at the right end of the desired line.
Once you have set the schedule, press "Confirm".
If you don't want to keep any changes, press
"Cancel" or use the calendar icon to go back.
You can modify the programmed purges by
selecting one and adjusting the schedule.
You have several possibilities for the schedule
(Mon-Fri, weekend, every day, or single days).
The schedules will be repeated every week.
The time and duration are set in 30 minute
increments. Once you have set the purge,
press "Confirm". If you don't want to keep
changes, press "Cancel" or the calendar icon.

15
1
water care
The Water care page will help you set up your ideal filtration and heating settings.The Water care page
will help you set up your ideal filtration and heating settings. Choose, set or modify one of the
5 suggested modes depending on your needs at any given time.
Away from home
In this mode the
spa will always be in
economy; the set point
will be reduced
by 20° F.
Beginner
The spa will never be
in economy mode
and will be filtering
according to the pack's
low level configuration.
Energy Savings
The spa will be in
economy mode during
the peak hours of
the day and resume
normal mode on
the weekend.
Super Energy
The spa will always
be in economy mode
during peak hours,
every day of the week.
Weekender
The spa will be in
economy mode from
Monday to Friday, and
will run normally on
the weekend.
modifying water care schedules
water care
To modify a Water care category, touch the pen
icon at the right end of the desired water care to
open the selected Water Care menu.
In Economy mode, the set point will be reduced
by 20°F, which means that the heating system
will not be engaged unless the temperature falls to
20°F below the spa's set temperature.
The filtration schedule show on the screen will be
applied to the main filtration pump, most likely
pump 1. If your spa uses a circulation pump
configured to run 24 hours, the screen will show
you the purge setting instead of filtration.
The purges are pre-programmed for a fix number
of minutes, therefore the duration will be set to
N/A on the screen, and only the start time can be
modified.
economy
Touch the Economy tab to change the economy
schedule. You can add economy schedules by
touching the orange line labelled "Add Economy" .
To delete a schedule, touch the garbage can icon
at the right end of the desired line.
You can modify the programmed schedules by
selecting one and adjusting the schedule.
You have several possibilities for the schedule
(Mon-Fri, weekend, every day, or single days).
The schedules will be repeated every week.
The time and duration are set in 30 minute
increments.
purges
Touch the Purge tab to change the purge
settings. You can add purges by touching the
orange line labelled "Add purge time".
To delete a schedule, touch the garbage can icon
at the right end of the desired line.
filter cycles
Touch the Filter cycle tab to change the filter
cycle schedules. You can add filtration schedules
by touching the orange line labelled "Add filter
cycle" .
To delete a schedule, touch the garbage can icon
at the right end of the desired line.
Once you have set the schedule, press "Confirm".
If you don't want to keep any changes, press
"Cancel" or use the calendar icon to go back.
You can modify the programmed purges by
selecting one and adjusting the schedule.
You have several possibilities for the schedule
(Mon-Fri, weekend, every day, or single days).
The schedules will be repeated every week.
The time and duration are set in 30 minute
increments. Once you have set the purge,
press "Confirm". If you don't want to keep
changes, press "Cancel" or the calendar icon.
1
maintenance
date and time
keypad settings
maintenance
To modify maintenance settings, slide the right
wheel until the maintenance icon is highlighted
in the middle.
From the Maintenance page you can access
the following:
• Reminders
• Standby
Simply touch the line of the item you want
to change.
date and time
To modify date and time settings, slide the right
wheel until the date and time icon is highlighted
in the middle.
Simply touch the line of the item you want to
change.
keypad settings
To modify keypad settings, slide the right wheel
until the keypad icon is highlighted in the middle.
Simply touch the line of the item you want to
change.
display contrast
Use this page to set or change the display day or
night contrast.
reminders
The in.k1000 keypad will provide reminders
about maintenance required on your spa, like
rinsing or cleaning the filter. Every task has its own
duration, based on normal use.
The reminders menu allows you to check the time
left before maintenance is required, as well as to
reset the time once a task has been completed.
To reset a task, select it by pressing the curved
arrow, then confirm when prompted. Once you
have confirmed, the task will be reset.
set date
Here you can adjust the year, month and date.
Simply swipe up and down the column you want
to change, and select the desired value. When
done, touch the calendar icon at the right of the
screen.
temperature units
Use this page to set or change the temperature in
F˚ or C˚ units.
display language
Use this page to set or change the display
language.
standby
The Standby mode allows you to service your
spa. Pumps will stop for 30 minutes and will
automatically restart after.
The normal page will return at the end, once the
pumps will be restarted.
set time
Here you can change the hour, minute and time
format.Simply swipe up and down the column
you want to change, and select the desired value.
When done, touch the calendar icon at the right
of the screen
display orientation
Use this page to set or change the normal or
inverted display orientation.

16
1
keypad settings
keypad lock/unlock (optional)
When this option is enabled, the user can partially
or completely lock the keypad.
When Full Lock is selected, all functions are
locked.
In Partial Lock, you may only activate accessories.
Settings may not be changed in this mode.
keypad color (optional)
If this option is available (depending on the spa
configuration), the keypad rim color can be
changed.
8 pre-defined colors are available. If the in.mix
is installed, the keypad rim color can also be
associated to an in.mix zone.
When the user wants to lock the keypad he is
asked to select a 4-digit code. The same code will
be needed to unlock the keypad.
Next time he wants to lock the keypad, he will be
prompted again to select a 4-digit code (same
functionality as a Safe in a hotel room).
The keypad can be unlocked with a universal
unlock code (3732) or by a reset of the keypad.
miscellaneous
This menu gives access to modify the Warm
Weather option and info messages in the media
center.
warm weather
When pumps are running, they produce heat that
may increase your water temperature. "Warm
Weather" option gives you the option to bypass
the pack filtration over-temperature feature.
When Warm Weather is "OFF" the filtration over-
temperature is disabled and your spa filtering will
continue even if the water temperature is high.
info messages
Press display/hide key to modify message display:
If hide option is selected, smart winter mode
message will only appear when a SWM purge is in
action. Otherwise the message will always appear
when the spa is in a SWM condition.
If hide option is selected, heating suspended and
filtering suspended messages will not appear.
miscellaneous
1
maintenance
date and time
keypad settings
maintenance
To modify maintenance settings, slide the right
wheel until the maintenance icon is highlighted
in the middle.
From the Maintenance page you can access
the following:
• Reminders
• Standby
Simply touch the line of the item you want
to change.
date and time
To modify date and time settings, slide the right
wheel until the date and time icon is highlighted
in the middle.
Simply touch the line of the item you want to
change.
keypad settings
To modify keypad settings, slide the right wheel
until the keypad icon is highlighted in the middle.
Simply touch the line of the item you want to
change.
display contrast
Use this page to set or change the display day or
night contrast.
reminders
The in.k1000 keypad will provide reminders
about maintenance required on your spa, like
rinsing or cleaning the filter. Every task has its own
duration, based on normal use.
The reminders menu allows you to check the time
left before maintenance is required, as well as to
reset the time once a task has been completed.
To reset a task, select it by pressing the curved
arrow, then confirm when prompted. Once you
have confirmed, the task will be reset.
set date
Here you can adjust the year, month and date.
Simply swipe up and down the column you want
to change, and select the desired value. When
done, touch the calendar icon at the right of the
screen.
temperature units
Use this page to set or change the temperature in
F˚ or C˚ units.
display language
Use this page to set or change the display
language.
standby
The Standby mode allows you to service your
spa. Pumps will stop for 30 minutes and will
automatically restart after.
The normal page will return at the end, once the
pumps will be restarted.
set time
Here you can change the hour, minute and time
format.Simply swipe up and down the column
you want to change, and select the desired value.
When done, touch the calendar icon at the right
of the screen
display orientation
Use this page to set or change the normal or
inverted display orientation.

17
1
keypad settings
keypad lock/unlock (optional)
When this option is enabled, the user can partially
or completely lock the keypad.
When Full Lock is selected, all functions are
locked.
In Partial Lock, you may only activate accessories.
Settings may not be changed in this mode.
keypad color (optional)
If this option is available (depending on the spa
configuration), the keypad rim color can be
changed.
8 pre-defined colors are available. If the in.mix
is installed, the keypad rim color can also be
associated to an in.mix zone.
When the user wants to lock the keypad he is
asked to select a 4-digit code. The same code will
be needed to unlock the keypad.
Next time he wants to lock the keypad, he will be
prompted again to select a 4-digit code (same
functionality as a Safe in a hotel room).
The keypad can be unlocked with a universal
unlock code (3732) or by a reset of the keypad.
miscellaneous
This menu gives access to modify the Warm
Weather option and info messages in the media
center.
warm weather
When pumps are running, they produce heat that
may increase your water temperature. "Warm
Weather" option gives you the option to bypass
the pack filtration over-temperature feature.
When Warm Weather is "OFF" the filtration over-
temperature is disabled and your spa filtering will
continue even if the water temperature is high.
info messages
Press display/hide key to modify message display:
If hide option is selected, smart winter mode
message will only appear when a SWM purge is in
action. Otherwise the message will always appear
when the spa is in a SWM condition.
If hide option is selected, heating suspended and
filtering suspended messages will not appear.
miscellaneous
1
wifi
(This function is available only if an in.touch module is connected to your system.)
wifi settings
To modify wifi network settings, slide the right
wheel until the wifi icon is highlighted in the
middle.
in.touch module not connected
If the in.touch module of your spa system is not
connected, this message will be displayed.
wifi networks
After a few seconds the available networks will
appear on-screen, as well as their signal strength.
Select network will be identified by a green check
mark.
Swipe Up or Down the list to select your network.
wifi network password
If the wifi network is password protected, enter
it when keyboard prompts. Use Enter key to
validate the password.
If no password is required the in.touch will
connect automatically.
electrical configuration
Please do not make changes in this section
unless you are a qualified electrician.
about
To get info about your spa system, slide the right
wheel until the about icon is highlighted in the
middle.
Information about the in.k1000 software number
and the revision numbers of the different
components of your system will be displayed.
about your spa system
wifi (in.touch 2)
When a in.touch 2 is detected, this network will
appear.
1
wifi
(This function is available only if an in.touch module is connected to your system.)
wifi settings
To modify wifi network settings, slide the right
wheel until the wifi icon is highlighted in the
middle.
in.touch module not connected
If the in.touch module of your spa system is not
connected, this message will be displayed.
wifi networks
After a few seconds the available networks will
appear on-screen, as well as their signal strength.
Select network will be identified by a green check
mark.
Swipe Up or Down the list to select your network.
wifi network password
If the wifi network is password protected, enter
it when keyboard prompts. Use Enter key to
validate the password.
If no password is required the in.touch will
connect automatically.
electrical configuration
Please do not make changes in this section
unless you are a qualified electrician.
about
To get info about your spa system, slide the right
wheel until the about icon is highlighted in the
middle.
Information about the in.k1000 software number
and the revision numbers of the different
components of your system will be displayed.
about your spa system
wifi (in.touch 2)
When a in.touch 2 is detected, this network will
appear.
1
too much water on display
wipe screen
This message appears when too much water is
detected on the touch screen. Simply wipe away
excess water.
installation error messages
Upon connecting the in.k1000 to your spa system you may see one of two error messages.
Please follow the instructions in the message or contact your dealer for more information.
Error messages on-screen list and definitions:
http://geckokeypads.com/k1000errormessages/
9919-101453-D Rev. 10-2017 www.geckoalliance.com
© Groupe Gecko Alliance Inc., 2017
All trademarks or registered trademarks are the property of their respective owners. Printed in Canada

18
1
direct to function
selection wheel:
on/off -
speakers -
source -
bluetooth -
mute / last track / play/pause / next track
mode selection
wheel:
audio mode
audio mode
(only available if the system detects a connected in.stream 2 audio station)
To select the audio mode, slide the left wheel up or down until the audio icon menu is highlighted in the middle.
In the Audio page you can access the following:
• in.stream 2 on/off • audio source selector
• speaker calibration • disconnect bluetooth
To select an item, slide the right wheel until the desired icon is highlighted in the middle.
on/off
speakers setting audio source selector disconnect bluetooth
turn in.stream 2 ON (icon red)
Slide the right wheel until the power on/off icon
is highlighted in the middle. Press the icon at the
center of the screen to turn in.stream 2 on.
to modify your speaker settings
Slide the right wheel until the speaker calibration
icon is highlighted in the middle.
You can adjust:
• balance
• fade
• subwoofer
Use the sliders to change the speaker settings at
the desired level.
The fade and subwoofer sliders will only appear
on the screen if the corresponding speakers are
installed on the in.stream 2.
turn in.stream 2 OFF (icon green)
Press the icon at the center of the screen to turn
in.stream 2 off.
to select an audio source
Slide the right wheel until the source icon is
highlighted in the middle.
In the menu list, the following sources are
available:
• Bluetooth
• FM
• USB
• Aux. 1
Simply select the desired one to use.
Note that only the sources installed on the
in.stream 2 will be displayed in the source menu.
Please note that the Play/Pause and Change
Track functions apply to devices using Bluetooth
technology and USB, and will not work when AUX
is selected as the source.
main display
Press Play / Pause to start or pause playback of
audio files.
Drag the volume slider to adjust the volume or tap
the mute button to mute or unmute sound.
Press the last track or next track buttons to go to
the previous song or skip to the next.
If a device with Bluetooth technology is connected
to the in.stream 2, you can disconnect it by
pressing the Disconnect key at the bottom of the
screen.
Doing so will also prevent the in.stream 2 from
automatically reconnecting to this specific device
until it has been reconnected using the device
itself.

19
1
direct to function
selection wheel:
on/off -
speakers -
source -
bluetooth -
mute / last track / play/pause / next track
mode selection
wheel:
audio mode
audio mode
(only available if the system detects a connected in.stream 2 audio station)
To select the audio mode, slide the left wheel up or down until the audio icon menu is highlighted in the middle.
In the Audio page you can access the following:
• in.stream 2 on/off • audio source selector
• speaker calibration • disconnect bluetooth
To select an item, slide the right wheel until the desired icon is highlighted in the middle.
on/off
speakers setting audio source selector disconnect bluetooth
turn in.stream 2 ON (icon red)
Slide the right wheel until the power on/off icon
is highlighted in the middle. Press the icon at the
center of the screen to turn in.stream 2 on.
to modify your speaker settings
Slide the right wheel until the speaker calibration
icon is highlighted in the middle.
You can adjust:
• balance
• fade
• subwoofer
Use the sliders to change the speaker settings at
the desired level.
The fade and subwoofer sliders will only appear
on the screen if the corresponding speakers are
installed on the in.stream 2.
turn in.stream 2 OFF (icon green)
Press the icon at the center of the screen to turn
in.stream 2 off.
to select an audio source
Slide the right wheel until the source icon is
highlighted in the middle.
In the menu list, the following sources are
available:
• Bluetooth
• FM
• USB
• Aux. 1
Simply select the desired one to use.
Note that only the sources installed on the
in.stream 2 will be displayed in the source menu.
Please note that the Play/Pause and Change
Track functions apply to devices using Bluetooth
technology and USB, and will not work when AUX
is selected as the source.
main display
Press Play / Pause to start or pause playback of
audio files.
Drag the volume slider to adjust the volume or tap
the mute button to mute or unmute sound.
Press the last track or next track buttons to go to
the previous song or skip to the next.
If a device with Bluetooth technology is connected
to the in.stream 2, you can disconnect it by
pressing the Disconnect key at the bottom of the
screen.
Doing so will also prevent the in.stream 2 from
automatically reconnecting to this specific device
until it has been reconnected using the device
itself.