Jacuzzi Premium J-315 User manual
Ozonator
O3
TB1
230 VAC, 3-Wire Connection
USE COPPER CONDUCTORS ONLY. WIRE SIZE MUST
BE APPROPRIATE PER NEC AND/OR LOCAL CODES
21
Flow Switch
Hi-limit/Freeze Sensor
Temperature Sensor
J2
J3
F1
20A
250V
SC-20
Circ.
Pump
Main
Pump
Spa
Light
Transformer
230 VAC
J4
HILO
GRN
Logic Jumper Settings
All Export 50 Hz Models:
JP1 1-2 ON = 20A Logic*
JP1 1-2 OFF = 30A Logic
*Factory Jumper Setting
Temp. Jumper Settings (All Models):
JP1 7-8 ON = Celsius Temp Display
JP1 7-8 OFF = Fahrenheit Temp Display
BLU BRN
JP1
4
2
3
1
6 5
8 7
Heater Specifications
• Export 50 Hz Model:
2.7 kW @ 230 VAC
J20
J21
J12
J14
J16
J11
J15
J13
J17 J7 J8 J9 J10
J5
J6
Heater IN Heater OUT
F1
K1
K2
K3
K4
K5 K7 K8
BLK
WHT
BRN
BRN
BLU
BLU
BLU
BRN
BRN
BLK BLU BRN BLU BRN
J1
Control Panel
LED Series Hot Tub Owner’s Manual
J-315TM, J-325TM, J-335TM, J-345TM,
J-355TM, J-365TM Models
2530-398, Rev. C
Attention New Spa Owner!
Congratulations on the purchase of your new Jacuzzi® spa! The following is a list
of automated functions performed by your spa. These functions are listed below
24-hours of ownership! Also listed below are important maintenance recommen-
dations you should observe on a regular basis to protect your new investment.
Automated Operations
heating cycle turns on pump 1. In J-335, J-345, J-355 and J-365 models, an
1 continues to operate for the duration of the cycle. Note: this function only
occurs during the rst ltration/heating cycle each day.
Maintain Healthy Spa Water
Always maintain your spa’s water chemistry within the following parameters as
information.
Required Filter Maintenance
unsurpassed water quality! To ensure maximum water quality at all times, you
Required Water Replacement
You should replace the spa’s water every 3 months. The frequency depends on
a number of variables including frequency of use, number of users, and attention
paid to water quality maintenance. You will know it is time for a change when you
the normal feel or sparkle to
the water, even though the key water balance measurements are all within the
pH
Free Chlorine
Free Bromine
Total Alkalinity
Calcium Hardness
7.4-7.6
100-120 ppm
150-250 ppm
3.0-4.0 ppm
2.0-4.0 ppm
Table of Contents
1.0 Important Spa Owner Information ................................ 1
2.0 Important Safety Instructions........................................ 2
3.0 Choosing A Location...................................................... 6
3.1 Outdoor Location .............................................................. 7
3.2 Indoor Location................................................................. 7
4.0 General Electrical Safety Instructions.......................... 9
5.0 Power Requirements.................................................... 10
6.0 Electrical Wiring Instructions...................................... 12
7.0 Spa Fill Up Procedure .................................................. 14
8.0 Control Functions......................................................... 18
.................................................................. 18
............................................ 20
9.0 Operating Instructions ................................................. 21
............................................. 21
9.2 ............................................................... 21
............................ 22
.. 23
... 23
................................. 24
.......................................... 24
................................................ 24
............................................................ 24
9.10 Air Controls..................................................................... 25
...................................... 25
10.0 Automatic Filtration Cycles......................................... 25
................................. 25
................................. 25
.................................................................... 26
........................... 26
11.0 Spa Maintenance .......................................................... 27
....................................................... 27
..................................................... 29
............................................... 30
..................................................................... 31
................................................... 31
................................. 31
...................................................................... 32
............................ 32
12.0 Water Quality Maintenance.......................................... 33
...................................................................... 33
........................................................................ 33
........... 34
13.0 Error Conditions/Error Messages............................... 34
................................................................ 34
13.2 Overheat Condition......................................................... 35
........................................................ 35
........................................................ 35
13.5 ............................................. 35
....................................................... 36
......................................................... 36
13.8 ......................................................... 36
14.0 Troubleshooting Procedures....................................... 36
............................... 37
........................ 37
............................................................... 37
............................................................. 38
.......................................................................... 38
15.0 J-315 Convertible Circuit Diagram (60Hz).................. 39
16.0 J-325/J-335/J-345/J-355/J-365 Circuit
Diagram (60Hz) ............................................................. 40
17.0 J-315 Export Circuit Diagram (50Hz) .......................... 41
18.0 J-325/J-335/J-345/J-355/J-365 Circuit
Diagram (50Hz) ............................................................. 42
19.0 Optional Stereo Receiver Functions .......................... 43
...................... 50
................................... 51
1.0 Important Spa Owner Information
Your Jacuzzi® spa is constructed to the highest standards and is capa-
retentive materials are utilized to insulate the spa for efficient operation,
an uncovered spa surface and wall fittings directly exposed to sunlight
and high temperatures for an extended period is subject to permanent
the spa full of water when it is exposed to direct sunlight and that you
keep the Jacuzzi insulating cover in place at all times when the spa is
not in use. Read and carefully follow the requirements for your spa’s
Jacuzzi spas constantly strives to offer the finest spas available,
therefore, modifications and enhancements may be made which
affect the specifications, illustrations and/or instructions contained
herein.
FCC Notice
This equipment has been tested and found to comply with the limits for
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is encouraged to
1. Rearrange or relocate the receiving antenna;
2. Increase the separation between the equipment and receiver;
3. Connect the equipment into an outlet on a circuit different from the
circuit connected;
(Changes or modifications not expressly approved by the party
2.0 IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY
-
1. WARNING: To reduce the risk of injury, do not permit children to use
this product unless they are closely supervised at all times.
2. WARNING: A grounding wire connector is provided on this unit to
2-
tor between this unit and any metal equipment, metal enclosures
of electrical equipment, metal water pipe, or conduit within 5 feet
3. DANGER:
exercised to prevent unauthorized access by children. To avoid
accidents, ensure that children cannot use this spa unless they are
supervised at all times.
4. DANGER: Risk of Injury. The suction fittings in this spa are sized to
arise to replace the suction fittings or the pump, be sure that the
-
rated less than the flow rate marked on the original suction fitting.
5. DANGER:
all metal surfaces. As an alternative, a spa may be installed within
5 feet of metal surfaces if each metal surface is permanently con-
2
conductor attached to the wire connector on the grounding lug,
inside the equipment compartment on the equipment box.
6. DANGER:-
ance, such as a light, telephone, radio, television, etc. within 5 feet
-
turer.
7. ELECTRICAL SUPPLY: The electrical supply for this product
must include a suitably rated switch or circuit breaker to open all
ungrounded supply conductors to comply with section 422-20 of the
be readily accessible and visible to the spa occupant but installed at
8. WARNING: To Reduce the Risk of Injury:
-
ered safe for a healthy adult. Lower water temperatures are recom-
mended for young children and when spa use may exceed 10 min-
utes.
-
ing fetal damage during the early months of pregnancy, pregnant or
possibly pregnant women should limit spa water temperatures to
using a spa.
temperature with an accurate thermometer since the tolerance of
12. The use of alcohol, drugs, or medication before or during spa use
may lead to unconsciousness with the possibility of drowning.
low or high blood pressure, circulatory system problems, diabetes,
infectious diseases or immune deficiency syndromes should consult
a physician before using a spa. If you experience breathing dif-
ficulties in association with using or operating your spa, discontinue
use and consult your physician.
a spa since some medication may induce drowsiness, while other
medication may affect heart rate, blood pressure, and circulation.
15. Always shower before and after using your spa. To reduce the pos-
sibility of contracting a waterborne illness, always maintain water
chemistry within the parameters listed on the inside cover of this
manual. If you or other bathers experience such a condition, dis-
continue use and seek medical attention.
IMPORTANT CSA SAFETY INSTRUCTIONS (CANADA ONLY)
1.
symbol* is located inside the supply terminal
box or compartment. To reduce the risk of electric shock, this
terminal must be connected to the grounding means provided in the
electric supply service panel with a continuous copper wire equiva-
lent in size to the circuit conductors that supply this equipment.
-
To reduce the risk of electric shock, connect the local common
bonding grid in the area of the spa to these terminals with an insu-
4. All field installed metal components such as rails, ladders, drains
bonded to the equipment grounding buss with copper conductors
5. SAVE THESE INSTRUCTIONS.
WARNING: Children should not use spas without adult supervision.
WARNING:
prevent body and hair entrapment.
WARNING:
WARNING: To avoid injury, exercise care when entering or exiting the
spa.
WARNING:
spa to avoid unconsciousness and possible drowning.
WARNING:
physician before using a spa.
WARNING:-
ous to your health.
WARNING:
with an accurate thermometer.
WARNING:
WARNING:
health.
WARNING:
-
ances are built-in by the manufacturer.
CAUTION:
instructions.
WARNING: The use of alcohol or drugs can greatly increase the risk of
fatal hyperthermia in spas.
SAVE THESE INSTRUCTIONS
HYPERTHERMIA
-
tion of the causes, symptoms, and effects of hyperthermia are as fol-
and an increase in the internal temperature of the body. The effects of
A warning sign is provided in your warranty packet. Please
install it at a location near your spa, where it is visible to the
user of the spa. For additional or replacement signs please con-
tact your local Jacuzzi dealer and reference item number #6530-
082.
CAUTIONS
pressure, and any condition requiring medical treatment, pregnant
women, the elderly, or infants should consult with a physician before
using a spa.
your health.
3. Observe a reasonable time limit when using the spa. Long expo-
sures at higher temperatures can cause high body temperature.
reduced awareness. These effects could possibly result in drown-
ing.
-
ous consequences.
5. Always test the spa water temperature before entering the spa.
operate any electrical appliances from inside the spa or when you
are wet unless such appliances are built-in by the manufacturer.
maintain safe water and prevent possible damage to spa
components.
use. This will help to discourage unsupervised children from enter-
ing the spa and keep the spa cover secure in high-wind conditions.
There is no representation that the cover, clip tie-downs, or actual
locks will prevent access to the spa.
3.0 Choosing A Location
IMPORTANT:
users, it is extremely important that the base upon which the spa rests
be smooth, flat, level and capable of uniformly supporting this weight,
without shifting or settling, for the entire time the spa is in place. If the
spa is placed on a surface which does not meet these requirements,
improper support is not covered under warranty. It is the responsibility
of the spa owner to assure the integrity of the support at all times.
provided it is constructed so that it meets the requirements outlined
above.
The spa must be installed in such a manner as to provide drainage
proper drainage could allow rain, overflow and other casual water to
flood the equipment and create a wet condition in which it would sit
to permit access to the equipment, either from above or below, for
prevent removal of all side cabinet side panels and access to the jet
components, especially on the side with the equipment bay.
3.1 Outdoor Location
In selecting the ideal outdoor location for your spa, we suggest that you
1. The proximity to changing area and shelter (especially in colder
2. The pathway to and from your spa (this should be free of debris so
3. The closeness to trees and shrubbery (remember that leaves and
4. A sheltered environment (less wind and weather exposure can
5. The overall enhancement of your environment. It is preferable not
to place the spa under an unguttered roof overhang since run-off
water will shorten the life expectancy of the spa cover.
3.2 Indoor Location
installing a spa indoors.
•Proper Foundation: -
ing a foundation that will adequately support the spa the entire time
roofs or other platforms not specifically tied into the main structural
experience in this type of application.
•Proper Drainage: It is extremely important to have in place mea-
flooring in which the spa rests on has adequate drainage and can
for ceilings and other structures that may be below the spas installa-
tion. Areas around your spa can become wet or moist so all flooring
and subsequent furniture, walls and adjacent structures should be
able to withstand or resist water and moisture.
•Proper Ventilation:
Engineer or authority competent enough to understand the neces-
sary provisions needed to vent moist or heated air and air associ-
-
erable amounts of moisture will escape, potentially causing mold
surroundings.
•Sufficient Access: In the unlikely event that you should ever need
to access or gain entry to any portion of the spa for servicing, it is
highly recommended that you plan your indoor installation to provide
full access to the entire spa.
•Warranty:
improper installation not in accordance to local codes or authorities
state or city building ordinances.
WARNING: In addition to maintenance of filters and water
chemistry, proper ventilation is recommended to reduce
the risk of exposure to viruses and bacteria that could be
present in the air or water. Consult a licensed architect
or building contractor to determine your specific needs if
installing your spa indoors.
4.0 General Electrical Safety Instructions
system. It contains the most advanced safety and self-protective equip-
department should you have any questions regarding your installation.
with a current collector system. A pressure wire connector is provided
on the surface of the control box, located outside the equipment door
this point and any ground metal equipment, metal water pipe or conduit
-
(8.4mm2
-
ment to insure installation conforms to local building codes.
120/240 Volt J-315 Convertible Models
enough to a grounded, grounding-type electrical outlet so that the
included power cord can be plugged directly into it.
as this could cause damage to the spa’s equip-
ment due to insufficient voltage. The power supplied to this spa must be
a dedicated circuit with no other appliances or lights sharing the power
provided by the circuit.
5.0 Power Requirements
Jacuzzi® spas are designed to provide optimum performance and flex-
ibility of use when connected to the maximum electrical service listed in
the tables below. If you prefer, your qualified technician can perform a
minor circuit board modification that allows the hot tub to operate on a
US/Canada J-325 1-Pump Models (60Hz)
240V/40A* 240V/50A**
* In the 40A configuration, the heater will not operate at the same time
as the high-speed jets pump.
** In the 50A configuration, the heater will operate at the same time as
the high-speed jets pump. This is the factory setting.
US/Canada J-315 1-Pump Convertible Models (60Hz)
120V/15A* 240V/30A* 240V/40A**
For 240 VAC Heater Operation:
-
components and void the manufacturer’s warranty.
*In the 15A and 30A configuration, the heater will not operate at the
same time as the high-speed jets pump. The factory setting is
120V/15A. Note: All Canadian spas must be hard wired (120 VAC
or 240 VAC) per CSA Canadian standards see page 4 for details.
**
#1-2 on the circuit board to allow the heater to operate at the same
230V/20A* 230V/30A**
* In 20A configuration, the heater will not operate at the same time as
the main jets pump. This is the factory setting.
** In 30A configuration, the heater will operate at the same time as the
main jets pump.
Export J-315/J-325 1-Pump Models (50Hz)
US/Canada J-335/J-345/J-355/J-365 2-Pump Models (60Hz)
240V/40A* 240V/50A** 240V/60A***
26A 36A 45A
*In 40A configuration, the heater will not operate while either jets
pump is running in high speed. Note: pump 2 runs only in high speed.
** In 50A configuration, the heater will not operate while both jets
pumps are running in high speed. Note: pump 2 runs only in high
speed. This is the factory setting.
*** In 60A configuration, the heater will operate while both jets pumps
are running in high speed. Note: pump 2 runs only in high speed.
Export J-335/J-345/J-355/J-365 2-Pump Models (50Hz)
230V/20A* 230V/30A** 230V/40A***
* In 20A configuration, the heater will not operate while either jets
pump is running in high speed. This is the factory setting.
Note: jets pump 2 runs only in high speed.
** In 30A configuration, the heater will not operate while both jets
pumps are running in high speed. Note: pump 2 runs only in high
speed.
*** In 40A configuration, the heater will operate while either jets pump
is running in high speed. Note: Jets pump 2 runs only in high speed.
6.0 Electrical Wiring Instructions
IMPORTANT NOTICE: The electrical wiring of this spa must
circuit must be installed by a qualified electrician and approved
1. Convertible J-315 120/240V 60Hz Power Models
A. 120V “Plug-in” Operation: This spa must operate on the supplied
-
ger runs. Never use an extension cord for any reason!
Convertible 120/240V Operation:
-
dance with these instructions will void both the independent testing
agency listing and the manufacturer’s warranty.
2. Dedicated 230-240V Power Models: This spa must be permanent-
No plug-in connec-
tions or extension cords are to be used in conjunction with the
operation of this spa.
accordance with these instructions will void both the independent
testing agency listing and the manufacturer’s warranty.
3. The power supplied to this spa must be a dedicated circuit with no
other appliances or lights sharing the power provided by the circuit.
4. To determine the current, voltage and wire size required, refer to
• All wiring must be copper to ensure proper connections. Do not use
aluminum wire.
2
the spa and reduce to short lengths of #8 (8.4mm2
to the spa.
5. The electrical supply for this product must include a suitably rated
switch or circuit breaker to open all ungrounded supply conductors
-
spa water.
6. The electrical circuit supplied for the spa must include a suitable
Figure-B, Control Box
1. T
2.
3. Terminal
3
2
1
9
10
4
37
1
2 2
Figure-A
Equipment Area
1.
2.
3.
4.
5. alve
6.
7.
8. p
9.
10.Ozone Injector
11
Note: Pump Locations Vary by Model
8
5
6 6
11
Article 680-42.
7. To gain access to the spa’s power terminal block, remove the
screws securing the cabinet panel on the side of the spa under the
power cable to control box, then install it through the large opening
provided in the bottom side of the box.
hooked up securely or damage could result.
10. Install control box door and screws and reinstall the cabinet side
panels.
7.0 Spa Fill Up Procedure
1. Prepare The Spa For Filling
• Clear all debris from the spa. (Although the spa shell has been
polished at the factory, you may want to treat it with a specially for-
mulated spa cleaner. Consult your authorized Jacuzzi dealer for
additional information prior to filling spa.
• Remove filter lid then remove filter cartridges from filter bucket.
2. Fill Spa
CAUTION:
hard water and the rest of the way with softened water. Or, you
may fill entirely with hard water if you use a special water addi-
tive available from your authorized Jacuzzi dealer.
BLUE
BLUE
BROWN
BROWN
1
2
US/Canada J-325/J-335/J-345/J-355/J-365
Models: 240 VAC, 3-Wire Connection (60Hz)
Figure-F
TB1
All Export J-315/J-325/J-335/J-345/J-355/J-365
Models: 230 VAC, 3-Wire (50Hz)
to Circuit
Board
BLK
RED LINE
NEUTRAL
Power In
RED
RED
BLK
BLK
1
2
Figure-E
TB1
to Circuit
Board
Power In
Green
TB3 Ground TB3
GRN
WHT
WHT
BLK
BLK
BLK
RED
1
2
3
Figure-C
TB1
to Circuit
Board
Power In
GRN
WHT WHT
BLK
BLK
BLK
RED RED
1
2
3
All US/Canada J-315 Convertible
Models: 120/240 VAC, 4-Wire Connection (60Hz)
Figure-D
TB1
to Circuit
Board
Power In
All US/Canada J-315 Convertible
Models: 120 VAC, 3-Wire Connection (60Hz)
the lowest headrest. .
IMPORTANT: Always fill your spa through the filter bucket after drain-
-
venting the pump from circulating water. Remove the hose and replace
both filter cartridges.
3. Turn On Power
Turn on power to spa at the home’s circuit breaker to start boot up
pump automatically activate after several seconds. If the control
COLICE
normal, refer to page 36 for additional information.
4. Activate Jets Pumps
adding start-up chemical in step 5.
5. Add Start-Up Chemicals
Add the spa water chemicals as recommended by your authorized
6. Establish A Stable Sanitizer Reading
Establish a stable sanitizer reading between 3.0-4.0 ppm Chlorine or
maintain a constant sanitizer reading within the levels recommended
inside cover of this manual. If sanitizer levels cannot be stabilized,
perform the decontamination procedure steps 9-15 on page 16-18.
Note: the “decontamination procedure” steps 9-15 should also be
used after the spa has been “Winterized” (section 11.7, page 32) or
has been sitting without power for an extended period.
7. Set Spa To Heat
To warm spa water to a comfortable temperature, follow these
-
COOLER (-) or WARMER
(+)
you want the water to heat to a different temperature, simply press
COOLER (-) or WARMER (+) within 5 seconds. The set tempera-
ture increases or decreases by one degree each time one of these
buttons is pressed.
• The heater will turn off when the temperature corresponding to the
thermostat setting is achieved.
Important Heater Details:
• The maximum temperature for which the spa can be set is
process. This will only result in a higher ultimate temperature.
8.Place Cover On Spa
• Keeping the insulating cover in place anytime the spa is not in use
will reduce the time required for heating, thereby minimizing operat-
ing costs.
• The time required for initial heat-up will vary depending on the start-
ing water temperature.
DANGER: Risk of injury, always check water temperature
carefully before entering spa!
Decontamination Procedure (Steps 9-15)
after performing steps 1-6 above.
after performing steps 1-6.
9.
model.
CAUTION:
any reason! This chemical may damage your spa and void the
manufacturer warranty.
Other manuals for Premium J-315
7
This manual suits for next models
5
Table of contents
Other Jacuzzi Hot Tub manuals
Jacuzzi
Jacuzzi J - 480 User manual
Jacuzzi
Jacuzzi Experience ALIMIA User manual
Jacuzzi
Jacuzzi SALON User manual
Jacuzzi
Jacuzzi Premium J-315 User manual
Jacuzzi
Jacuzzi J-145 User manual
Jacuzzi
Jacuzzi lodge M User manual
Jacuzzi
Jacuzzi NOVA 6 User manual
Jacuzzi
Jacuzzi Riva 6 User manual
Jacuzzi
Jacuzzi Z100 User manual
Jacuzzi
Jacuzzi Fuzion 7260 User manual
Jacuzzi
Jacuzzi Premium J-315 User manual
Jacuzzi
Jacuzzi PowerActive Swim SPA Series User manual
Jacuzzi
Jacuzzi Majora 5 User manual
Jacuzzi
Jacuzzi NOVA 6 User manual
Jacuzzi
Jacuzzi FUZION 7236 RH User manual
Jacuzzi
Jacuzzi Bellavista 6 User manual
Jacuzzi
Jacuzzi Cetra 532 User manual
Jacuzzi
Jacuzzi J-200 Series User manual
Jacuzzi
Jacuzzi Luxura 5 User manual
Jacuzzi
Jacuzzi Delos User manual
Popular Hot Tub manuals by other brands
Aquatic
Aquatic AI37LUX6036 Specification sheet
Iberspa
Iberspa SM-USO/INS-PR User's operation manual
American Standard
American Standard CADENZA ELITE 6060E SERIES installation instructions
Aquatic
Aquatic AIPL6042SY Specification sheet
HotSpring
HotSpring Pulse instructions
Takara Belmont
Takara Belmont Yume Oasis installation instructions