AquaSource 67354-1008D2 User manual

AquaSource®is a registered trademark
of LF, LLC. All Rights Reserved.
ITEM #0017758
0016531
PULL-DOWN
KITCHEN FAUCET
uestions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-866-417-7564, 8 a.m. - 8 p.m., EST, Monday - Friday.
1
MODEL #67354-1008D2
67354-1027H2
ATTACHYOUR RECEIPT HERE
Serial Number Purchase Date

PACKAGE CONTENTS
2
A
B
C
D
E
F
G
H
M
I
J
K
L
N
O
P
Q
R
1
1
Hose (Preassembled to Faucet (A))
Faucet
A
Shank (Preassembled to Faucet (A)) 1
Rubber Washer (Preassembled to Shank (C)) 1
Base Plate (Preassembled to Faucet (A))
Escutcheon (Preassembled to Faucet (A)) 1
1
B
F
E
C
G
D
1
1
Flange
Nut (Preassembled to Shank (C))
H
Quick Connector (Preassembled to Hose (B)) 1
Body Assembly 1
Weight
Tab (Preassembled to Quick Connector (J)) 1
1
I
M
L
J
N
KBlock(Preassembled to Faucet (A)) 1
Pump 1
Bottle
Mounting Nut (Preassembled to Body Assembly (N)) 1
1
P
O
Q
Metal Washer (Preassembled to Shank (C)) 1
Mounting Nut (Preassembled to Faucet (A)) 2
R
DESCRIPTION QUANTITYPART

3
PREPARATION
Before beginning the assembly of product, make sure all parts are present. Compare parts with
package content list and diagram above. If any part is missing or damaged, do not attempt to
assemble the product. Contact customer service for replacement parts.
Estimated Assembly Time: 60 minutes, Including Removal of Old Faucet
Tools Required for Assembly (not included): Adjustable Wrench, Phillips Screwdriver, Pliers,
Putty/Silicone, Allen Wrench
Helpful Tools (not included): Basin Wrench, Water Supply Lines
Please read and understand this entire manual before attempting to assemble, operate or install
the product. If you have any questions regarding the product, please call customer service at
1-866-417-7564, 8 a.m. - 8 p.m., EST, Monday - Friday.
• Follow the installation instructions carefully. Proper installation is the installer's responsibility.
• Failure to follow correct installation procedures can result in the faucet being loose, which can
result in serious injury.
• Check local building codes before beginning installation to ensure compliance.
SAFTEY INFORMATION

ASSEMBLY INSTRUCTIONS
4
2. For single hole installation, refer to diagram 2A.
Place flange (I) on the sink (not included).
For 3 hole installation refer to diagram 2B. Place
base plate (E) and escutcheon (D) on the sink. Do
not use flange (I) if you are using the escutcheon
for 3 Hole installation. From underneath the sink,
hand tighten mounting nut (R).
1. Shut off water supplies. Remove old faucet. 1
DO NOT USE THE FLANGE (I) IF YOU ARE
USING THE ESCUTCHEON
2A
I
2B
D
E
R

ASSEMBLY INSTRUCTIONS
5. Connect 1/2 in. IPS faucet connector or coupling
4. To install the hose (B), screw quick connector (J)
to the free end of hose (B). Align block (K) and
tab (L) on quick connector (J). Push quick
connector (J) housing firmly upward and snap onto
block (K). Pull down moderately to ensure connection
has been made. If it is necessary to remove the hose,
press on the tabs (L) and pull quick connects (J) down.
After connecting the hose (B), attach weights (M) to
hose (B) at bottom of loop to prevent hose (B) from
twisting and return hose (B) to proper position.
5
nuts (not included) with 3/8 in. O.D.ball-nose
risers (not included) to water supplies using
wrenches (not included).
Note: Refer to local plumbing codes for
permissible types of water supply connectors.
5
4
K
J
L
M
B
3. Remove quick connector (J) from the hose (B)
by unscrewing it counter clockwise. Retract
hose (B) up through faucet (A), until the hose (B)
fitting is flush with the bottom of shank (C). Do
not pull fitting past the shank (C). Insert faucet (A)
through holes in top of sink. From underneath sink,
install rubber washer (F), metal washer (G) and
nut (H) onto the mounting shank (C).
Note: Do not feed the hose (B) back down through
the spout until step 4.
3.
F
G
H
B
C
A
3
J

ASSEMBLY INSTRUCTIONS
6
7. The installation is completed. Now remove the
sprayer from the spray hose by unscrewing it in
a counterclockwise direction and turn the water
for at least one minute for each hot and cold.
Check for leaks. Re-tighten any connections if
necessary, but do not overtighten. Reinstall
sprayer head by hand tightening it back onto the
spray hose. Do not let go of the hose until you
have reattached the sprayer.
7
6. To install soap dispenser, insert body assembly
(N) through selected hole of sink. Secure body
assembly (N) to sink with mounting nut (O).
From under the sink screw the bottle (P) onto
the shank of body assembly (N). Insert pump (Q)
down into the body assembly (N).
N
O
P
Q
6

CARE AND MAINTENANCE
TROUBLESHOOTING
7
• Clean carefully by gently wiping with a grit-free damp cloth. Use only mild soap with water.
Never use acids, harsh chemicals or abrasive detergents to clean surface.
This faucet has been manufactured under the highest standard of workmanship. All parts of this faucet
are warranted to be free from leaks or drips during domestic use for as long as the original purchaser
owns this product. THIS EXCLUDES INDUSTRIAL, COMMERCIAL, OR BUSINESS USE. The
manufacturer will replace FREE OF CHARGE, under the warranty conditions the entire unit or any
part (at our option) which proves defective in material and/or workmanship under normal installation,
use and service. This warranty is limited to defective parts as stated. All costs of removal and
installation of the faucet, including the replacement of warranty parts are the responsibility of the
purchaser. The manufacturer shall not be liable for incidental, consequential or special damages
arising at or in connection with product use or performance except as may otherwise be accorded by
law. This warranty gives you specific legal rights, and you may also have other rights which may vary
from state to state. Any damage to this faucet as a result of misuse, abuse, neglect, accident,
improper installation, or any use violating instructions furnished by us, WILL VOID THIS WARRANTY.
When requesting warranty service, you will need to present a copy of your sales receipt as proof of
purchase. To obtain warranty service, call our customer service department at 1-866-417-7564.
If you have any questions regarding the product, please call our customer service at 1-866-417-7564,
8 a.m. - 8 p.m., EST, Monday - Friday.
LIFETIME LIMITED WARRANTY
Leak from under handle Damaged cartridge Remove handle. Replace cartridge.
Inconsistent flow pattern Aerator is dirty or misfitted Unscrew the aerator to check rubber
washer or replace the aerator.
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Leak from the spout/aerator Damaged cartridge Remove handle. Replace cartridge.

REPLACEMENT PARTS LIST
8
For replacement parts, call our customer service department at 1-866-417-7564, 8 a.m. - 8 p.m., EST,
Monday - Friday.
Printed in China
*Available in Stainless Steel Finish and OilRubbed Bronze Finish.
56789 10
11
12
23
15
16
20
13
14
21
24
17
18
19
22
1
23.1
23.2
23.3
2
4
3
Cartridge RP20044
RP70291
RP38090*
Handle RP13209*
Handle Seat RP17123*
RP70289
RP60075
O-Ring RP60076
Clip RP70288
Inverter
Sprayer Assembly
Wearable Ring
Clip RP70290
1
2
3
4
5
11
10
9
8
7
6Bonnet
Connect RP50125
12
13
14
Set Screw
Block RP50002
RP70005
O-Ring RP60002
RP64111
Bolt RP50071
Nut RP56063
RP80274*
Metal Washer
Base Plate RP80275
20
19
18
17
16
15 Escutcheon
Rubber Washer RP64131
21
22
23
Mounting Nut
Weight RP56036
RP70223
23.1 Soap Dispenser
Pump RP46039*
RP46040*
23.2
23.3 Body Assembly RP46021*
Bottle
Flange & Washer RP46002
RP80278*
24
DESCRIPTION PART #
PART