Ara-Unicontrol Uniwifi User manual
Ara-Unicontrol
1
Manual wifi for devices
Ara-Unicontrol.
P
Please consider the environment before printing this document.
PLEASE, YOU MUST READ THE ENTIRE INSTRUCTION MANUAL BEFORE
YOU THE INSTALLATION AND USE OF YOUR CONTROL DEVICE OF STOVE OF
BIOMASS.
Content.
Pág. 2 Wifi module.
Pág. 3 Connection wifi module.
Pág. 4-6 Wifi networ configuration.
Pág. 7-21 Access to the web www.unicontrolnet.com
Unicontrol (Viriato) 02/2019
2
Read the instructions in this instruction manual carefully!
Before connecting the mains cable to the socket on the back of the stove, lug the Uniwifi module into the
DB9 connector (see figure 1). Then connect the network cable and follow the instructions below.
2
Figure 1
Once the stove is connected, we will observe the following sequences:
1 - Software version and serial number. 2 - Configuring wifi module .......
3 - Wifi module configured. 4 - In the u er line corres onds to the user's
name and the lower line corres onds to the
assword. Follow the instructions that begin at
the end of this age.Once the configuration is
finished press the menu key. The CPU will
complete the test.
5 -Start test It will be done every time
reconnect the stove.
6 - Selected stove model.
7 - Chec ing air level in depression. In this case, it
must be equal to or greater than the value found on the
right: .53mB.
8 - Screen without activity. Indicates that the stove
is ready to light.
Establish connection with the "UniWiFi" module in your Wi Fi network.
In a device that has Wi-Fi (smartphone, tablet, computer ...), select the following networ : ARA_AP,
password: 12345679. If your device does not dis lay the ARA_AP network for one minute, disconnect the
stove, ress and hold the decrement key (<) and reconnect the stove. Sto ressing the decrement key (<),
when the sequence number 2 a ears on the screen.
Check if your device shows the ARA_AP network. Then o en the browser and enter the following address in
the search bar IP: 10.10.100. 54
3
Insert in "User name": ARA and in "Password": ARA
Select "STA Setting" and clic on "Scan" with the cursor.
4
Choose Wi-Fi networ and validate with "OK".
Enter the password (password), corresponding to the selected Wi-Fi networ and validate with "SAVE".
5
The configuration has been made. Press "Restart".
The wifi module has been restarted with the new configuration.
6
Enter the username and assword you will find in sequence number 2 on age 1,
and then ress the ENTER key
8
Press the green rectangle enter.
9
Select stove status, in the top bar.
10
Press the blue colored rectangle, connect.
11
The LCD tab corresponds to the display which has the same functions as the physical display on the stove.
The button below the display is used to update the data on the screen for 30 seconds.
12
Tab 2 contains two calendars. Before making any modification it is necessary to ress the blue rectangle to
receive the calendar from the stove, in this way we can see the reviously rogrammed data. Once the new
rogramming is done, we will record the same ones by ressing the red rectangle to send the new calendar
to the stove. Calendar 2 is rogrammed in the same way.
13
14
15
The M1 tab indicates the settings made in the menu 1. We press the blue rectangle to receive values from the
stove.
16
The tab M2, indicates the general information corresponding to menu 2.
17
The tab load / update model, allows us to add a new model or update the existing model. The available files
have information about whether they are new models or updates of old models.
18
19
20
