Arbor Technology Double Bay User manual

01945 410950 [e-mail]
http://www.arborgardensolutions.co.uk
Trading address: Unit 11, Cattle Dyke, Wisbech, England, PE1 34NR
Generic build instructions –Double Bay log store
Before you commence the assembly process, we recommend that you read these
instructions thoroughly beforehand to familiarise yourself with the assembly process and to
also check that you have the correct components.
We highly recommend that any assembly is carried out on a flat, level surface if possible
and that you use another person to assist you if necessary.
You can check our YouTube channel for assemble video, click on the link below:
Double Bay wooden log store - assembly video
Package contents:
2x Side panels
2x Back panels
2x Centre posts
1x Base
1x Lattice
1x Roof
65mm screws
6x 85mm screws (for the base only)
2x Spacer blocks
Tools required:
Electric screwdriver (No.2 Pozi bit) or
Screwdriver

01945 410950 [e-mail]
http://www.arborgardensolutions.co.uk
Trading address: Unit 11, Cattle Dyke, Wisbech, England, PE1 34NR
Arrange the 2 spacer blocks on the ground
(the orientation is not critical), adjacent to
the end panel as shown in the photo above.
Now place a back panel on the blocks, at 90°
to the end panel, aligning the 2 panels ready
for fixing.
Using the 65mm screws provided, attach the
batten on the back panel to the post of the
end panel, ensuring that the batten remains
vertically aligned to the post.
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
Ensure that you have all the correct parts as
listed on the front page of these instructions,
including any fixings.
Stand the left-hand end panel (or right hand for
the reversed roof version) upright on a flat, level
surface.

01945 410950 [e-mail]
http://www.arborgardensolutions.co.uk
Trading address: Unit 11, Cattle Dyke, Wisbech, England, PE1 34NR
Align one of the longer posts (shorter for a
reversed roof) with the other end of the back
panel.
Attach the panel to the post by screwing
through the batten using 65mm screws as
before.
Rearrange the spacer blocks and offer up the
next panel, aligning and attaching it as before.
Remove the blocks from beneath the 2nd panel
and then slide the base into position as shown,
ensuring that the centre post and the central
cross member of the base are aligned in the
middle of the back assembly.
Step 7
Step 8
Step 9
Step 10

01945 410950 [e-mail]
http://www.arborgardensolutions.co.uk
Trading address: Unit 11, Cattle Dyke, Wisbech, England, PE1 34NR
Slide the remaining end panel into place as shown
above and attach it to the frame as you did with the
first end panel with 85mm screws into the front and
rear posts. If you are fitting a kindling shelf, omit
steps 12 -14 and attach the front posts before fitting
the kindling shelf & lattice and then attaching the
roof.
Carefully place the roof on top of the log store.
Step 11
Step 12
Step 13
Step 14
Attach the base to the end panel front post first,
using 1 of the 85mm screw and then secure the
rear post in the same way.
Using more of the 85mm screws now attach the
base to the rear posts as shown.

01945 410950 [e-mail]
http://www.arborgardensolutions.co.uk
Trading address: Unit 11, Cattle Dyke, Wisbech, England, PE1 34NR
Check that the batten ends sit flush with the posts
as shown. Now attach the roof to each end panel
post with 65mm screws.
Secure the rear of the roof using 65mm screws as
shown.
Sit the lattice in the store so that it is leaning
against the back panel as shown above, so that
you have enough clearance to attach the front
posts as shown in the next step.
Fit a central post into the slotted roof position.
By measuring the distance from the side panel
to the central post and making sure it is equal at
the bottom and the top. (The space from the
side panel to the central post must be equal to
the back panels measurements).
Step 15
Step 16

01945 410950 [e-mail]
http://www.arborgardensolutions.co.uk
Trading address: Unit 11, Cattle Dyke, Wisbech, England, PE1 34NR
Step 17
Step 18
Step 19
Step 20
Make sure that the centre post sits flush
with the roofs batten ends and secure in
place with 1 of the 65mm screws.
After making sure that the gap at the bottom is
the same as in the top attach the centre post to
the base panel with the provided 1x 80mm
screw.
Your Double Bay log store is now complete.
If you are fitting doors, please proceed with
step 20 hinge to the post.
Place a spacer block at the front of the log
store adjacent to the front-end post and rest
the hinge side of the appropriate door on
the block, aligning it vertically and
horizontally for a good fit. Now use four of
the supplied black hinge screws to affix the
hinge to the post.

01945 410950 [e-mail]
http://www.arborgardensolutions.co.uk
Trading address: Unit 11, Cattle Dyke, Wisbech, England, PE1 34NR
Fit the hook to the opposite side of the doors from the hinges to whichever
height is the best for you with 2x black screws. Don’t forget to attach the
provided batten to the other side of the doors while screwing in the black
screws to hide the pointy screw end’s sticking out of the doors.
To fit the latch keeper plate, shut the
door and hold the latch in the
horizontal position. Now fit the
keeper and mark its correct fixing
position on the post using a pencil or
bradawl before securing it in place
using the screws provided.
Step 21
Step 22
Step 23
Step 24
Align the top hinge in place, ensuring that
the gap between the door and post is
consistent at top and bottom.
Secure the top hinge in place using more of
the black hinge screws. Repeat steps 20 - 22
for any further doors as required.

01945 410950 [e-mail]
http://www.arborgardensolutions.co.uk
Trading address: Unit 11, Cattle Dyke, Wisbech, England, PE1 34NR
Your double bay log store is now completed!
We hope that you found your product quick and easy to assemble but if not and you require further
assistance or have any questions you can contact us via details above.
Also, you can check our YouTube channel for assemble videos, click on the link below:
https://www.youtube.com/channel/UC3b2MzAv6fTkCPnC3QF7V9w
Or type in YouTube search box Arbor Garden Solutions.