Arcadia ISO User manual

5692 FRESCA DRIVE, LA PALMA, CA 90623 | 800.585.5957 | ARCADIACONTRACT.COM
ISO CONFIGURATIONS WITH PANELS – T-BRACKET
ASSEMBLY INSTRUCTIONS
Hardware Included (quantity varies per configuration):
[A] ¼-20 x 1.25” pan head bolt (24)
[B] ¼-20 x 1.1875” flat head bolt (27)
[C] ¼-20 x .25” flat head bolt (21)
[D] Corner bracket
[E] T-bracket
IMPORTANT – HARDWARE IS SPECIFIC FOR THE ASSEMBLY OF EACH COMPONENT. MAKE SURE THE
CORRECT ITEMS ARE USED AS DIRECTED AND IDENTIFIED BELOW.
**UNIT REQUIRES TWO PEOPLE FOR INSTALLATION**
*IF UNIT IS SHIPPED WITH LEGS PRE-INSTALLED, SKIP STEPS 1 & 2*
Step 1: Gently place the unit on its side and locate the holes with pre-inserted t-nuts where the legs will attach
(Figure A).
Step 2: Attach each leg by securing with (6) ¼-20 x 1.25” pan head bolts [A] into the pre-inserted t-nuts
(Figure B).
Note: Upon completion of Step 2, return the unit to upright position by lifting unit. Do not tilt or lean unit to
upright position.
continued on next page
[A] [B] [C] [D] [E]
FIGURE A
FIGURE B
[A] ¼-20 x 1.25” pan head bolt, qty. 12

5692 FRESCA DRIVE, LA PALMA, CA 90623 | 800.585.5957 | ARCADIACONTRACT.COM
Step 3: Open the privacy panel to reveal the attachment holes. Starting with the back of the chair, align the
holes with the pre-inserted t-nuts and secure with (4) ¼-20 x 1.1875” flat head bolt [B]. Follow with
side panels using (5) ¼-20 x 1.1875” flat head bolt [B] per side (Figure C).
Step 4: Align and secure the Corner bracket [D] to the right side (from the rear view) with an Allen wrench
and (3) ¼-20 x .25” flat head binding bolts [C]. Align and secure the T-bracket [E] to the left side in
the same way (Figure D).
Step 5: Secure each bracket to the back panel with (6) ¼-20 x .25” flat head bolt [C] into the
pre-inserted t-nuts (Figure E).
Step 6: Once the panels have been properly secured, remove the yellow masking tape covering the Velcro
and firmly press the panels together (Figure F).
continued on next page
FIGURE E
FIGURE F
[C] ¼-20 x .25” flat head bolt, qty. 6
FIGURE C
FIGURE D
[B] ¼-20 x 1.1875” flat head bolt, qty. 16
[C] ¼-20 x .25” flat head bolt, qty. 6
[D] Corner bracket
[E] T-bracket
Velcro

5692 FRESCA DRIVE, LA PALMA, CA 90623 | 800.585.5957 | ARCADIACONTRACT.COM
Step 7: Align and secure the corner bracket to the secondary unit and affix back and left panels (Figure G).
Step 8: Open the back panel where the other half of the t-bracket will attach and arrange the units as they
should be configured. Align the t-bracket from the already installed unit to the pre-inserted t-nuts on the
secondary unit. Using an Allen wrench, secure together with (3) ¼-20 x .25” flat head bolts [C]
(Figure H).
Step 9: Once the panel is properly secured, remove the yellow masking tape covering the Velcro and firmly
press the panels together (Figure I).
If you require additional assistance, please contact Arcadia Client Services at 800.585.5957.
[A] ¼-20 x 1.25” pan head bolt, qty. 12
[B] ¼-20 x 1.1875” flat head bolt, qty. 11
[C] ¼-20 x .25” flat head bolt, qty. 6
FIGURE G
FIGURE H
Velcro
FIGURE I