Arcisan Kudos KU06112 User manual

Kudos 75 Backlit Mirror
KU06112
Volts: 220-240V (hardwire)
Power rating: 41W
Backlit: Yes
Demister: Yes
Clock: No
Magnifier: No
The Kudos mirror is one of the new feature packed LED
backlit mirrors from Arcisan.
It uses the latest LED technology for long life, low
electricity usage and an even spread of light, unlike
older uorescent lit mirrors. The lights and demister are
operated via the touch switch.
Quality is assured through the use of high quality oat
glass and 100% silvering on the rear that is completely
sealed against any moisture penetration.
Size is 750mmx 800mm.
5 years
WARRANTY
Dimensions are in millimeters and are subject to manufacturing variations. Streamline
reserves the right to vary specications at any time without notice. Information provided
within this specication sheet is correct at the date of printing. Please conrm all
particulars with your sales consultant prior to purchase.
Version: 1.3 - February 2020
www.streamlineproducts.com.au | Ph: 1300 735 352
*Conditions apply.
30
800
740
83
750
690
Demister
400 x 300
270
100
light box
LED
35
400
375
240v

Fitting Instructions for Arcisan Mirror
132
DIMENSIONS
X&Y
Ø6
1. Handle with care. When unpacked, never place mirror upright on a
hard surface e.g. Tile Floor. Always lay on soft surface.
2. Drill 2 holes on wall surface as per diagram 1 to desired
height.64”from oor to centre of mirror is advised but may be
adjusted as required, Use spirit level to ensure holes are level. If
drilling through tiles, use a ceramic drill bit.
3. Inset rawl plugs into holes and screws into holes.
4. Attach wire from back of mirror to mains wire in accordance with
current IEE regulations. A second person will be needed to hold the
mirror in place.
5. Hang the mirror onto the screws via holes in the frame.
6. Some mirrors may be hung portrait or landscape.
7. Adistance of 80 mm is necessary between the sensor switch and
any other object in any direction
8. Enjoy!
This mirror is suitable for Zone 2 or higher and not Zone
0 or 1 (see diagram)
We advise that you consult a qualied electrician for the
installation.
Switch off electrical supply at mains before tting.
Ensure wall surface is of suitable strength and
construction.
Beware of hidden cables or pipes.
For plasterboard walls, specialist xings should be
purchased from DIY or hardware stores.
The mirror is heavy so you may need assistance.
Turn lights on/off using infra red sensor -leave off when
not in use.
Heat pat turns on with light switch and takes 2/3 minutes
to heat up.
FITTING INSTRUCTIONS GENERAL INFORMATION
Thanks for purchasing an Arcisan mirror. For safety reasons,we kindly ask you to read
this installation and user guide carefully before you install and use the product.
X
Ø8
Y
X
X
1 - Long press on left key, clock enters in setting up mode.
First number starts flashing. Press the right key to choose
numbers, 1 or 2.
2 - In setting mode, short press on left key, choose number
position to adjust,then press right key to choose the number.

Fitting Instructions for Arcisan Mirror
Instructions apply to all the following mirrors:
800
900
750
800
800
600 1200
800
700
750
750
700
900
700
1200
700
1400
700
900
700
1200
700
900
700
1200
700
900
700
700
1200
PZ 06110
Ø850
KU 06110
600x800
KU 06112
750x800
KU 06114
900x800
KU 06116
1200x800
EN 06110
750x700
EN 06210
750x700
EN 06211
900x700
EN 06214
1200x700
EN 06216
1400x700
AR 06112
900x700
AR 06114
1200x700
LY 06112
900x700
CY 06114
1200x700
KB 06110
900x700
KB 06112
1200x700
Mail: 21Compark Circuit,Mulgrave,Victoria-3170
Emali: [email protected].au
Streamline Products P/L
Phone: Victoria:8545 0690
All other states:1300 735 352
850
Ø