ArcVision Technology ARC 19601 User manual

1CH Digital Video Recorder
Thank you for purchasing our product. Please read this User＊s Manual before using the product.
1 Channel Digital Video Recorder
V1.1
- 1 -

SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC
SHOCK. DO NOT OPEN!
CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN COVERS.
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This label may appear on the bottom of the unit due to space limitations.
The lightning flash with an arrowhead symbol within an equilateral triangle is intended
to alert the user to the presence of uninsulated ?dangerous voltage?within the
product enclosure that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
presence of important operating and maintenance (Servicing) instructions in the
literature accompanying the appliance.
WARNING : TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE UNITS NOT
SPECIFICALLY DESIGNED FOR OUTDOOR USE TO RAIN OR MOISTURE.
Attention: installation should be performed by qualified service Personnel only in
accordance with the National Electrical Code or applicable local codes.
Power Disconnect. Units with or without ON-OFF switches have power supplied to
the unit whenever the power cord is inserted into the power source ; however, the unit
is operational only when the ON-OFF switch is in the ON position. The power cord is
the main power disconnect for all unites.
- 2 -

BEFORE READING THIS DOCUMENT...........................................................................................5
UNIT DESCRIPTION ...........................................................................................................................6
1FRONT PANEL....................................................................................................................................6
2REAR PANEL......................................................................................................................................7
3CONTROLLER ....................................................................................................................................8
INSTALLATION....................................................................................................................................9
1.CAMERA CONNECTION.......................................................................................................................9
2.MONITOR CONNECTION .....................................................................................................................9
3.TRIGGER CONNECTION ....................................................................................................................10
4.NETWORK CONNECTION ..................................................................................................................10
5.HDD CONNECTION..........................................................................................................................10
6.POWER CONNECTION .......................................................................................................................10
OPERATION........................................................................................................................................11
1.LOG-IN............................................................................................................................................11
2.RECORDING.....................................................................................................................................12
3.PLAY ...............................................................................................................................................15
4.SETUP..............................................................................................................................................17
(1)Start of SETUP.........................................................................................................................17
(2)DISPLAY SETUP....................................................................................................................19
(3) CAMERA SETUP...................................................................................................................19
(4) TIME/DATE SETUP..............................................................................................................21
(5) ALARM/MOTION SETUP....................................................................................................22
(6)RECORD SETUP ....................................................................................................................25
(7)TCP/IP SETUP.........................................................................................................................27
(8)MISCELLANEOUS SETUP ...................................................................................................28
HDD BAY..............................................................................................................................................33
1.HDD EXTENSION........................................................................................................................33
2. HDD BAY.....................................................................................................................................33
SPECIFICATIONS ..............................................................................................................................34
1.SPECIFICATION.................................................................................................................................34
2.CONFIGURATION OF SINGLE CHANNEL DVR....................................................................................35
3.RS-232C HEX-CODES TABLE ..........................................................................................................35
- 3 -

MANUALFOR REMOTE VIEWER SOFTWARE .........................................................................37
1GENERAL DESCRIPTION ....................................................................................................................37
2.TCP/IP SETUP IN DVR UNIT .........................................................................................................37
3.STATIC IP AND DYNAMIC IP ............................................................................................................38
4.LIVE VIEW VIA IP NETWORK ............................................................................................................41
5.SEARCH RECORDED PICTURES VIA IP NETWORK ..............................................................................45
- 4 -

 Before reading this document
(1) This document is intended for both the administrator and users of stand-alone
DVMR unit
(2) This manual contains information for configuring, managing and using stand
alone DVMR unit.
(3) To prevent fire or electrical shock, do not expose the product to heat or moisture.
(4) Be sure to read this manual before using stand alone DVMR unit.
(5) For question and technical assistance of this product, contact your local dealer.
(1) Check electricity at the place you want to install the DVR unit is stable
and meets our electricity requirements. Unstable electricity will cause
malfunction of the unit or give critical damage to the unit.
(2) Several chips on the main board of the DVR unit and hard disk drive
inside the unit generate heat, and it must be properly discharged. Do not
put any objects just beside exhaust port on the left side of the unit and do
not close up an opening on the right side of the unit.
(3) Put the DVR unit at well-ventilated place and do not put heat-generating
objects on the unit. When it is installed inside 15 inch mounting rack
together with other devices, please check built-in ventilation fan of the
rack is properly running.
- 5 -

 Unit Description
1 Front Panel

LED: (over write/Rec/Play/Setup)
P/T: Enter into or exit from PAN/TITL control mode.
SPEED: In full screen, this button shows pictures in rotation.
MARK: mark when it is in playback mode
FRZ: On-off switch to freeze pictures in live mode
PLAY: Play-Back
MENU: used to change menu in system setup
Enter: Used as selection key in system setup or changes contents displayed in live
display.
Dirtection button
- 6 -

2 Rear Panel


HDD BOX
TRIGGER
RJ45
LOOP BACK
VCR
RS232/RS485/IO ALARM Connection
DC Power
VIDEO OUT
- 7 -

3 Controller
P/T: Enter into or exit from PAN/TITL control mode.
SPEED: In full screen, this button shows pictures in rotation.
MARK: mark when it is in playback mode
FRZ: On-off switch to freeze pictures in live mode
PLAY: Play-Back
MENU: used to change menu in system setup
ENTER: Used as selection key in system setup or changes contents displayed in
live display.
- 8 -

 INSTALLATION
1.Camera connection
Connect camera the camera input on the rear panel of the system.
2.Monitor connection
Connect the monitor to the monitor out on the rear panel of the system.
- 9 -

3.Trigger connection
Connects to trigger port of multiplexer in case you replace time lapse VCR used in
connection with multiplexer.
TRIGGER
TRIGIN/GND
4.Network connection
Connects to HDD BOX, Multiplexer or network
5.HDD connection
Be sure to set jumper setting for each HDD as per HDD manufacturer’s
spjecification
Main board
HDD
(Default) HDD (Option)
6.Power connection
Connect the poser to the power connection on the rear panel of the system, and
turn on the switch.
DC 12V
- 10 -