AREBOS AR-HE-GH70CM User manual

User’s Manual –AREBOS Built-in Gas hob
1
Built-in Gas hob
AR-HE-GH70CM
User’s Manual
Please follow all security measures in this user’s manual to ensure a secure use.

User’s Manual –AREBOS Built-in Gas hob
2
Please read and save these instructions. Read through this user’s manual carefully before using
product. Protect yourself and others by observing all safety information, warnings and cautions.
Failure to comply with instructions could result in personal injury and/or damage to product or
property. Please retain instructions for future reference.
Safety instructions
•Your safety is of the most importance to us. Please make sure that you read this instruction
booklet before attempting to install and use the appliance. If you are unsure of any of the
information contained in this booklet, please contact the Retailer where you purchased your
unit.
E
n
•Ensure that these notes and that the whole of this instruction book are thoroughly read and
understood before installation or operation of the hob.
•The instructions are provided in the interest of your safety.
Explanation of the symbols
WARNING: Read all safety warnings and instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or serious injury. Save all warnings and
instructions for future reference. DO NOT use the hob until you read the instruction
manual.
Warning! Read the safety instructions carefully. Failure to follow the safety
precautions could result in serious injury or damage. Keep the operating
instructions in a safe place.
Warning! Connect an earth terminal to the ground!
Warning! Hot surface
By means of a CE marking, it can be recognized that a product complies with the
legal requirements of European legal standards and therefore may be traded
within the European Community.
This product must not be disposed of with household waste!

User’s Manual –AREBOS Built-in Gas hob
3
Gas Safety Regulations
•It is the law that all gas appliances have to be installed by competent persons in accordance
with current edition of the above regulations. It is In your interest and that of safety to
ensure compliance with the law.
•Repairs or servicing of this product must be carried out only by an authorized agent service
using only approved parts.
•No attempt has to be made to modify this appliance.
•Cooking appliances become very hot in use, therefore ensure children and pets keep away.
The use of oven gloves is recommended during use.
•Do not allow children to operate or play with any part of the appliance.
•Do not use unstable pans and position handle away from the edge of the hob. The use of a
suitable hob service is recommended.
•In the interests of safety and hygiene, ensure the hob is kept clean as a buildup of grease
could cause fire.
•This appliance is only designed for domestic cooking, commercial catering may invalidate the
warranty.
•Do not cover the hob or place combustible materials on or near the surface even when the
hob is not in use.
•Do not fill deep fat frying pans more than one third full of oil. Do not leave unattended.
•Before cleaning the hob, switch off at the mains.
•When finished cooking, switch all controls off and allow to cool.
•If you sell or transfer ownership of this product, please pass on these instructions to the new
owner.
•This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety.
•Children should be supervised to ensure that they do not play with the appliance.
•If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or
a similarly qualified person in order to avoid a hazard.
•Do not immerse appliance or power cord into water or any other liquids.
•Please pull the pin out when you do cleaning and maintenance. When the appliance is
installed, you can pull out the pin.
Warning! Flammable material!
Warning of electrical voltage!

User’s Manual –AREBOS Built-in Gas hob
4
Operation
•Even if you have used a gas hob before, it is important that you read these instructions
thoroughly before starting to cook, paying particular attention to the installation and safety
instructions. If you have any problems with installing, operating, or cooking with your hob,
please check through these instructions thoroughly to make sure that you have not missed
anything.
•WARNING: For your own safety, make sure that these instructions on Installation, use and
maintenance are followed.
•We advise you to keep these instructions in a safe place for future reference. If you sell or
transfer ownership of this product, please pass on these instructions to the new owner.
Installation
Technical Information
•The Installation, the adjustments, conversions and maintenance listed in this part must only
be carried out by qualified persons. The safety and automatic adjustment devices of the
appliance may only be modified by an authorized safety agent. The Installation of this gas
hob must comply with the standards in force. This appliance is not connected to a flue for
discharge of the combustion products; therefore, it must be connected in compliance with
the above mentioned installation rules. Particular attention must be paid to the instructions
given below for ventilation and aeration.
•WARNING: The appliance must be connected to a combustion products evacuation device. It
shall be installed and connected in accordance with current installation regulations.
Particular attention shall be given to the relevant instructions regarding ventilation.
Location
•The cooker may be located in a kitchen, kitchen/diner or a bed-sitting room, but not in a
room containing a bath or shower. The hob must not be installed in a bed-sitting room of less
Semirapid
gas
burner
1750 W
Semirapid
gas burner
1750 W
Rapid
gas
burner
3000 W
Auxiliary
gas
burner
1000 W
Triple flame gas
burner 3800 W

User’s Manual –AREBOS Built-in Gas hob
5
than 20m3. LPG models shall not be installed in a room or internal space below ground level,
e.g. in a basement.
Provision for ventilation
•The room containing the cooker should have an air supply. The room must have an opening
window or equivalent; some rooms may also require a permanent vent. If the room has a
volume between 5 and 10m3, it will require an air vent of 50cm2effective area unless it has a
door which opens directly. If the room has a volume of less than 5m3, it will require an air
vent of 100cm2effective area (Fig. 1). If there are other fuel burning appliances in the same
room, the same room should be consulted to determine air vent requirements.
•NOTE: The use of a gas cooking appliance results in the production of heat and moisture in
the room in which it is installed. Always ensure that the kitchen is well ventilated; keep
natural ventilation holes open or install a mechanical ventilation device (Fig. 2). In particular,
when using the grill or more than one hotplate burner, open a window if a mechanical
ventilation device is not operating (Fig. 3).
(*) Air inlet minimum section: 100 cm2
Unpacking the appliance:
•Remove all packaging before use and check to make sure that the appliance is In perfect
condition. If you have any doubts do not use the appliance and call your supplier. Some parts
on the appliance are protected by a plastic film. This protective film must be removed before
the appliance is used. We recommend carefully slitting the plastic film along the edges with a
sharp knife or pin. The packaging materials should carefully discarded and not left within
easy reach of children as they are a potential safety hazard.
Installing and fixing the hob:
•Your hob can be fitted to any worktop with a thickness of 40 to 50 mm, accordance with no
overhanging surface or cooker hood should be closer to the hotplate than 750 mm. Fix in
position in Fig. 4. If fitting a 600 mm bridging unit above the 700 mm hob unit, the sides of
adjacent cabinets may be lower than 760 mm down to 334 mm provided they are resistant
to heat and steam. The hob has a special seal which prevents liquid from entering the
cabinet. Follow these instructions in order to correctly apply this seal:
•Detach the seals from their backing, that the transparent protection still adheres to the seal
itself. Turn over the hob and correctly position seal *E* (Fig. 5) under the edge of the hob
itself, so that the outer part of the seal itself perfectly matches the outer edge of the hob.
The ends of the strips must fit together without overlapping. Evenly and securely fix the seal
to the hob, pressing it firmly in place.
Fig.1
Fig.2
Fig.3

User’s Manual –AREBOS Built-in Gas hob
6
Installation options
•Option: When fitting a gas hob above a drawer or standard housing unit, suitable
precautions must be taken to prevent contact. The panel underneath the hob must be easily
removable to allow for any servicing requirements with the casing of the hob, which
becomes very hot during operation. The recommended method for overcoming this problem
is to fix a wooden panel within the cabinet at a distance of 15mm below the underside of the
hob (see figure below). This panel must have adequate ventilation to the rear.
Inserting and fixing the hob:
•Before inserting the hob into the work surface, place the adhesive seal (a) around the
underside edge of the hob. It is important to fix this gasket evenly, without gaps or
overlapping to prevent liquids from seeping underneath the hob.
-Remove the pan stands and the burner caps then turn the hob upside down, taking care
not to damage the ignition plugs and the thermocouples.
-Place the gasket around the bottom edge of the hob as shown in the illustration overleaf
(left).
-Place the hob in the installation opening and push it down so that the hob is resting
firmly on the cabinet.
-Secure the hob in position using the fixing brackets supplied.
-
•Secure the hob to the underside of the worktop using the fixings provided. Screw one end of
the bracket into the pre-drilled holes in the underside of the hob. The other end of the
bracket should be located underneath the worktop to secure the hob in position.
Fig. 4
Fig. 5
Ventilation Slot >30mm
Fixing bracket
Worktop
Screw

User’s Manual –AREBOS Built-in Gas hob
7
Gas Connection
•The appliance's gas inlet fitting is a 1/2" male threaded conic gas type in accordance with the
ISO 7-1 standards. Make the connection using rigid pipe. When making the gas connection, it
is important to place the gasket (A) in between the inlet pipe (C) and the elbow (B), to ensure
a gas tight seal.
Electrical connection
•This appliance must be connected by a competent person, using fixed wiring via a double
pole switched fused spur outlet with a fuse rating of 3 amps, and with a contact separation of
at least 3mm in all poles. We recommend that the appliance is connected by a qualified
electrician who will comply with I.E.E regulations. The wires in the mains lead are coloured in
accordance with the following code: Green & Yellow = Earth, Blue = Neutral, Brown = Live.
•Replace the injectors with the corresponding injector from the table on page below (see Fig.
6). First, remove the burner caps and rings and with a socket spanner "B", unscrew Injector
"A" (see Fig. 6).
•The adjustment of the reduced rate position is as follows (Fig. 7): Light the burner and turn
the knob to reduced rate position.
•Remove the knob "M" which is simply inserted onto, tap stem. Insert a small screwdriver "D"
into the top shaft "C" and turn the bypass screw left or right until flame of the burner is
conveniently regulated to the low position.
•Make sure that when turning quickly from "Full on" position to reduced rate position that the
burner does not extinguish.
B
C
A

User’s Manual –AREBOS Built-in Gas hob
8
•
•
Injector replacement table
User Instruction
•To light the hotplate push in the appropriate control knob and turn anti-clockwise to the
large flame symbol (Fig. 8).
•Keep the knob depressed until the burner lights.
•Turn the tap to the required setting.
•In the event of the burner flames being accidentally extinguished, turn off the burner control
and do not attempt to reignite the burner for at least 1 min.
•NOTE: Matches can be used to light the burners in the event of a power failure. Keep the
control knob pressed in for 15 seconds ensuring the burner stays lit when released. If the
burner fails to stay lit wait for 1 minute before relighting.
Fig. 6
Fig. 7
Fig. 8
Fig. 9

User’s Manual –AREBOS Built-in Gas hob
9
Select the right burner
•Use an appropriately sized pan and with flat bottom for each burner (see the table below and
Fig. 9). When the contents of the pan start to boil, turn the knob down to reduced rate
position. Always put a lid on the pan.
•NOTE: Please do not use cooking vessels that overlap the boundaries of the hob.
Technical Specifications
Model
AR-HE-GH70CM
Voltage/Frequency
AC220-240 V 50/60Hz
Power
11.3 kW
Front (left) zone
1,75 kW
Rear (left) zone
1,75 kW
Rear (right) zone
3 kW
Front (right) zone
1 kW
Middle (Front) Zone
3.8 kW
Energy efficiency
55.75%
Product Dimensions
700*510 mm
Build-in dimensions W*L
477*557 mm
Colour
Black/White/Red/Ivory Glass
Weight Net/Gross
12/13.5 kg
Propange gas*
yes
* Note! The change to propane gas must be carried out by a qualified specialist, otherwise the
warranty expires!
Fault finding guide
•Check the guide below if there Is a problem with your hob.
UNEVEN OR YELLOW FLAME RATHER THAN BLUE?
•Switch off and check the following points:
-Are the burners fitted correctly?
-Are the holes in the burner clear?
-Check that no dust has fallen into the flame turning it yellow
ATTENTION! This appliance must be installed in compliance with the current provisions in
force and only used in rooms equipped with adequate ventilation. Consult the instruction
manual before proceeding with installation or use of the appliance.

User’s Manual –AREBOS Built-in Gas hob
10
BURNER FAILING TO IGNITE?
•Check that the power is turned on or that the fuse has not blown. Make sure that the ignitor
isn't coated with food spillage.
SPARK BUT NO GAS?
•Make sure the gas is turned on. Check that the burner holes are not blocked.
SMELL GAS?
•Check to see if any gas tap has been left on. If they are off, switch off gas at mains and call a
service agent.
DO NOT search with a naked flame, strike any matches or press ignitor.
STILL NOT WORKING?
•Call the service Agent.
Cleaning
Vitreous enamel
•Hotplate, burner caps, pans supports. Cloth wrung out in hot soapy water. Stubborn stains
can be removed with a cream paste approved by the Vitreous Enamel Development Council,
liquid cleaner or by rubbing with fine steel wool soap pads.
Aluminium
•Hotplate burner bodies. Similar to paint cleaning above. Use a nylon brush to remove any
cleaning materials, water or dirt from the hotplate burner bodies. After cleaning, wipe dry
and refit to the hob ensuring they are correctly seated. Check parts are reassembled
correctly by lighting the burners and allowing to dry out.
Plastic
•Control knobs. Wipe with a cloth wrung out in hot soapy water.
Stainless steel
•Cloth wrung out in hot soapy water.

User’s Manual –AREBOS Built-in Gas hob
11
Disposal instruction
Disposal of the packaging
•Please make reference to the guidelines and standards for appropriate disposal of the packaging
valid in your region. In part, the package may consist of plastic bags - watch this respect, with
special care to ensure that this is not out of the reach of children. There is a risk of suffocation!
Disposal of waste equipment
•Equipment must be disposed of in accordance with the rules and regulations of the local waste
disposal.
Meaning of the "dustbin"
Protect our environment; electrical appliances do not belong in household waste.
Use the provided for the disposal of electrical equipment collection points and
enter your electrical and electronic equipment that you no longer use. They help
ensure that the potential effects of incorrect disposal on the environment and
human health to be avoided. So, do your part to recycle, recycling and other
forms of recovery of waste electrical and electronic equipment. Information on
where the devices are disposed of, please contact your local authorities or local
Governments.
Our customer service number: [phone]
Canbolat Vertriebs GmbH • Gneisenaustraße 10-11 • 97074 Würzburg

User’s Manual –AREBOS Built-in Gas hob
12
EU Declaration of Conformity
We,
Canbolat Vertriebs GmbH, Gneisenaustraße 10-11, 97074 Würzburg, Germany,
Hereby declare that the product named below, seen its design and construction as well as according
to our sales, has been complied with the relevant and basic health and safety EU-requirements.
Name of the product: AREBOS Built-in gas hob
Model number: AR-HE-GH70CM
Art. No. 4260199756768
If the product has any modification not allowed by us, this declaration loses its validity.
Tested acc. to:
EU Standard:
ISO9001: 2008 GB/T19001-2008
Date/Manufacturer Signature/Location: Würzburg, 18.02.2019
Identification of the signatory:
Korhan Canbolat, head of the company
Authorised representative for the technical documentation:
Korhan Canbolat
Office address:
Canbolat Vertriebs GmbH
Gneisenaustraße 10-11
D-97074 Würzburg
Return address can be found in the imprint: https://www.arebos.de/impressum/
VAT identification number: DE 263752326
Court of the Commercial Register is Würzburg, HRB 10082
WEEE Reg.-No. DE 61617071