Arec ARECare MV-01 User manual

MV-01
ENGLISHQuick Installation Guide
All Rights Reserved 2023
All information contained in this document is Proprietary
ARECare Intercom Solution

MV-01
MV-01 Quick Installation Guide
1
FCC
Federal Communication Commission interference statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures: -Reorient or relocate the receiving antenna. -Increase the
separation between the equipment and receiver. -Connect the equipment into an outlet on a
circuit different from that to which the receiver is connected. -Consult the dealer or an
experienced radio/TV technician for help.
RF Exposure Warning
The equipment complies with RF exposure limits set forth for an uncontrolled environment. The
antenna(s) used for this transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
You are cautioned that changes or modifications not expressly approved by the party responsible
for compliance could void your authority to operate the equipment.
FCC Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference that may
cause undesired operation
This equipment should be installed and operated with a minimum distance of 20 centimeters
between the radiator and your body.
Notice: Any changes or modifications not expressly approved by the party responsible for
compliance could void your authority to operate the equipment.
CE
Hereby, AREC Inc., declares that this Media Station is in compliance with the essential
requirements and other relevant provisions of Directive 2014/53/EU.

MV-01 Quick Installation Guide
2
CB
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
– the ventilation should not be impeded by covering the ventilation openings with items, such as
newspapers,table-cloths, curtains, etc.:
– no naked flame sources, such as lighted candles, should be placed on the apparatus;
– attention should be drawn to the environmental aspects of battery disposal;
– the use of apparatus in tropical climates.
the instructions for use shall state that the apparatus shall not be exposed to dripping or
splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

MV-01 Quick Installation Guide
3
Introduction
Specifications
Package Contents
ARECare Intercom Solution includes 3 different kinds of I/O hardware for selection. Each model
could be configured as Presenter mode or Viewer mode for two-way communication. Viewer
mode supports Android/iOS apps for mobile devices. Make communication more convenient!
ARECare Intercom System
MV-01S MV-01U MV-01C
650g 490g 330g
95mm(L) x 80mm(W)
x 83mm(H)
95mm(L) x 80mm(W)
x 65mm(H)
95mm(L) x 80mm(W)
x 38mm(H)
Product Name
Model Name
Dimension
Weight
12V
Power Requirement
40W(Max.)
Power Consumption
0°C ~ 40°C / 90%
Operating Temperature
/Humidity
Supports 3 channel of video & audio signal input, include 2 HDMI and
1 IP Cam/Stream or UVC video, and one line-in or Mic-in audio.
Output the transcoded video to the HDMI port(with GUI) and loop
through one HDMI video source at the same time. Record the video
file to the USB storage via USB port or SD card slot.
Maximum normal
load description
Power Adapter
MV-01 Quick Installation Guide

4
1
2
3
4
5
6
7
8
9
10
11
12
SD Card Slot
Reboot Button
Mic-In
Line-In
HDMI-In 2
HDMI Loop Out
LAN Port
WAN Port
USB-in
HDMI Out
Power Port
Power Button
* NOTE : The MV-01 can detect and record to USB storage devices using FAT32, NTFS, exFAT,
Ext3, Ext4 file systems.
NO. I/O Interface Function Description
For internal storage of the recording videos
Reboot the device
Connected with microphone.
Connected with audio mixer or amplifier
HDMI input source, connected with PC or cameras.
(Max. 3840x2160@30Hz)
Loop through HDMI video source (Max. 3840x2160@30Hz)
Connected with network cameras or PC/NB for settings
For the external communication or remote control.
1. Available for the USB audio/video inputs
2. Available for the USB mouse and touch devices
3. Available for the USB storage
Display graphic user interface, video, call list. (Max. 1920x1080@60Hz)
12V 3.34A
When the device is ON, push twice to turn OFF
Long press 3 seconds to restart
When the device is OFF, push to turn ON.
12
3
7
9
10 11
12
8
4 5 6
Product Appearance
MV-01 Quick Installation Guide

12
35
6 7
8
4
5
Product Appearance
1
2
3
4
5
6
7
8
SD Card Slot
Reboot Button
LAN Port
WAN Port
USB-in
HDMI Out
Power Port
Power Button
* NOTE : The MV-01 can detect and record to USB storage devices using FAT32, NTFS, exFAT,
Ext3, Ext4 file systems.
NO. I/O Interface Function Description
For internal storage of the recording videos
Reboot the device
Connected with network cameras or PC/NB for settings
For the external communication or remote control.
1. Available for the USB audio/video inputs
2. Available for the USB mouse and touch devices
3. Available for the USB storage
Display graphic user interface, video, call list. (Max. 1920x1080@60Hz)
12V 3.34A
When the device is ON, push twice to turn OFF
Long press 3 seconds to restart
When the device is OFF, push to turn ON.
MV-01 Quick Installation Guide

MV-01 Quick Installation Guide
6
12
54 6
7
3
1
2
3
4
5
6
7
SD Card Slot
Reboot Button
WAN Port
USB-in
HDMI Out
Power Port
Power Button
* NOTE : The MV-01 can detect and record to USB storage devices using FAT32, NTFS, exFAT,
Ext3, Ext4 file systems.
NO. I/O Interface Function Description
For internal storage of the recording videos
Reboot the device
For the external communication or remote control.
1. Available for the USB audio/video inputs
2. Available for the USB mouse and touch devices
3. Available for the USB storage
Display graphic user interface, video, call list. (Max. 1920x1080@60Hz)
12V 3.34A
When the device is ON, push twice to turn OFF
Long press 3 seconds to restart
When the device is OFF, push to turn ON.
Product Appearance

MV-01 Quick Installation Guide
7
Connection
USB
IP cam
projector
TV
Power
notebook
network
記憶卡
HDMI video output
external hard disk
USB camUSB Keyboard
Speakerphone
USB mouse
Line audio input
amplifier
Mic audio input
Equipment
Medical PC
Camera
HDMI video input
microphone
HDMI video output
projector
TV

8
Getting start
Connecting to network
Connect MV-01S/U/C to a router or switch. You would need to prepare a public IP or fixed IP for
the MV-01 device which assigned to be the conference server.
Connecting with the Display and HID devices
MV-01 devices provide graphic user interface, you need a touch panel(1920x1080) or at least a
display and a HID device to operate the functions. Connect your MV-01S/U/C with a touch panel
via HDMI output and USB port.
Configure video & audio inputs
Video Input
MV-01 devices support HDMI, UVC(USB Video Class), network cameras, and IP video sources.
1. Connect your video source.
• HDMI: Connect the source to HDMI input 1 or 2
* If you intend to use your video source for other device/monitor, please connect the source
to HDMI input and connect the other device to the HDMI loop-through port.
• UVC(USB): Connect the USB video source to the USB port.
* If there are multiple USB devices needed for your case (USB cameras/mouse/flash drives…
etc.), we recommend to use a USB hub which comes with its own power adaptor to provide
more stability for your USB source and devices.
• Network camera or IP source: Connect the source under the same subnet with MV-01.
2. Go to the MV-01’s web page to set the video input
• Open a browser and insert the MV-01’s IP address. The IP address can be found on the GUI
menu shown on display that connected to the HDMI preview output port. Click on the “ ”
icon in the bottom tool bar to find the IP address of the device.
MV-01S
MV-01S
192.168.0.136
V7.6.3.3
Operation Room
• Login the web administrator page with default
username/password: admin/admin
MV-01 Quick Installation Guide

9
3. Configure your video source
Please select “Video port” in Signal type, and select the corresponding option in
“Video source”. And click “Apply”to take effect.
• HDMI & USB video source
First, go to the Network device manager page and click scan to find your network camera.
Click “Login” and insert the camera’s ONVIF credential to register the camera.
Go back to the Video inputs page, and select “Network Camera” in Signal type and select the
camera in IP address. Click “Apply” to take effect.
• Network camera
MV-01 Quick Installation Guide

10
IP source
MV-01 supports RTP/RTMP/RTSP for video inputs. Please select “IP source” in Signal type and
insert the correct stream URL in “Primary URL”.
Click “Apply” to take effect.
Audio Input
MV-01 support multiple audio input types: Line-in/Mic-in/HDMI/USB audio input.
Connect your audio input source to the MV-01 and go to web administrator →Media I/O →
Audio page to configure the volume level.
If you are using USB audio source, please select your USB audio device in the “USB Audio (UAC)
settings” drop-down list.
MV-01 Quick Installation Guide

11
Configure MV-01 User Modes
1. There are 2 modes for the selection, Presenter or Viewer mode. Go to the web administrator →
Conference →Service settings →Conference mode.
2. Click the “Apply” button to finish settings. The system will restart to make it valid.
MV-01 Quick Installation Guide
Conference Server Settings
1. Go to the web administrator →Conference →Conference settings.
2. Select Internal in the “Conference service” drop-down list.
Change the Authentication Key and remember it.
3. Click on “Apply” to finish the settings.
Configure Conference Related Settings

12
Configure conference clients
1. Go to the web administrator → Conference → Conference settings.
2. Select External in the “Conference service” drop-down list.
Input the IP address of the conference server and 5070 as the communication port. Then Input
the Authentication key, same as the conference server.
3. Click on “Apply” to finish the settings.
4. Check the contact list on Presenter unit’s GUI or Conference server’s administration webpage,
you could see a new device registered and show on the list.
MV-01 Quick Installation Guide

13
MV-01 Quick Installation Guide
Add a storage on your MV-01
For the recording purpose, you need to prepare a storage and mount into the device. Please
insert a SD card or USB storage and do the format process as follow.
1. Open the browser and log into the admin webpage.
2. Go to Storage → Disk Information, you will find the inserted storage. Click on “Format”.
3. Make sure you select the correct storage.

14
MV-01 Quick Installation Guide
Important Security Policy
Precautions
1.Please open the product package carefully; we commend you keep this packaging for future
transport, storage or maintenance use.
2.There are no switches or adjustment buttons required for operation inside this product, so
for your safety, please do not open the casing on your own, or vigorously rotate, shake or
use any other inappropriate ways to operate this product in order to avoid electrical shocks
and voiding the warranty. You can contact a local dealer directly if you have any questions.
3.Heat will be generated during the use of this product; therefore there must be sufficient
ventilation for the temperature of the unit to remain at a stable status. So please use the
product under normal environments to prolong the usage life, and avoid installing it in the
following environments.
Locations that are unstable or have incomplete planes
Locations with powerful magnetic fields
Locations where it is damp or may have water leakage
Locations that are too hot, close to heaters and air hoses, or be exposed to direct sun
light for long periods of time
Locations that are dusty
Locations where there are possible shocks
Locations close to power amplifiers
4.If you notice smoke or odor coming from the product, please quickly remove the power cable
and send it to a maintenance center for processing.
5.To avoid electrical shock, the plug of the adapter should be stably and completely inserted
into the power outlet and cannot be exposed; it must also have sufficient capacity to
withstand the current transmission. Please do not plug the adapter into the power outlet
before connecting the cable in order to avoid danger.
6.If not used for long periods of time, please unplug the power plug, and to ensure electrical s
afety, when unplugging the adapter, please hold the plastic part of the adapter with dry hands
and then unplug the adapter. Please properly connect the cables according to the printed
instructions on the installation manual and the machine to ensure optimized usage effects.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED
BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS

All Rights Reserved 2023
All information contained in this document is Proprietary
Made in Taiwan
Date : 2023.01.01
Version : 2.20