Connect the post (A) to the cup holder base (B) by aligning the
groove on the base to the ridge inside the bottom of the post.
Place the universal cup holder mount into the designated cup
holder in the vehicle. Adjust the thumbwheel adjuster (C) to
expand or close the cup holder prongs to t in the cup holder.
MM323
|Cup Holder Mount for Magellan®, Mio®, and Navman® GPS Devices
Package Contents:
(1) CM033-2 - Cup holder pedestal mount
(1) APMM300 - Dual-T to Mio Moov 300 pattern adapter plate
!Safety Precautions
Do not install Arkon products over an air bag cover or within the air
bag deployment zone. Arkon Resources, Inc. assumes no responsi-
bility of liability for injury or death as a result of car crashes and / or
air bag deployment.
Arkon is not responsible for any damages caused to your car, your
device, or yourself due to the installation or use of this pedestal mount.
The Mobile Mounting Specialists™
www.arkon.com
Arcadia, CA 91006 USA
Designed in USA | Made in Taiwan
© Copyright 2008 Arkon Resources, Inc.
Consumer Hotline:
USA (800) 841-0884
INT’L (626) 254-9005
Monday - Friday 9 am - 5 pm, PST
Do not place mount in or near an air bag deployment zone or where it will
obstruct view of the road.
!
APMM300
Dual-T Adapter Plate
Patent Pending
All brand names and product names are trademarks or registered trademarks of their respective owners.
CM033-2
Cup holder mount
Cup Holder Mount Installation
(B) Cup Holder Base
(A) Cup Holder
Post
(C) Thumbwheel
adjustment
knob
(D) Angle adjustment nut
Step 1.
Step 2.
(E) Optional
support
pads
CLOSE
OPEN
For oversize cup holder openings or the adjustable “pop out”
cup holders use the optional self-adhesive side support pads
(E). Install the pads by removing the adhesive backing and
placing it on the at surface side of the cup holder support leg.
Step 3.
Step 1. Attach the device to the cup holder mount by inserting the
dual T-Tabs on the pedestal head (F) into the T-slots on the
back of the adapter plate (G).
Connect GPS Device to Cup Holder Mount
(F)
(G)
(H)
(I)
Step 2. Insert the adapter plate with power cord into the vertical
groove pattern on the back of the GPS device (not included,
sold separately.)
Step 1. Insert the power cord (not included, sold separately) into the
grooved slot in the bottom of the adapter plate.
Connect Power Cord to Adapter Plate and Device Attachment
Compatible with:
• Magellan Maestro: 3100, 3140, 3200, 3210, 3220, 3225, 3250, 4000, 4010, 4040, 4050,
4210, 4215, 4200, 4220, 4245, 4250, 4350, 4370, 4700, 5310, and 5340
• Magellan RoadMate: 1200, 1210, 1212, 1215, 1220, 1230, 1340, 1400, 1412, 1430, 1440,
1470, 1475T, 2000, 2200T, 2250T, 300, 3000T, 3050T, 360, 500, 500 Plus, 6000T, 700, 760,
800, and 860T
• Magellan Triton: 1500, 200, 2000, 300, 400, and 500
• Magellan Crossover: GPS 2500T
• Mio Moov: 300, 301, 310, 330, 330 Europe, 360, 370 Europe, 380, 500, and Knight Rider Ed.
• Navman: S50, S50 3D, S70, S90i
Step 1. If your Magellan device has dual-T slots on the back, attach
the GPS unit to the cup holder mount by connecting the dual
T-slots (H) to the dual T-tabs of the mount head (I).
Dual-T Device Attachment
...continued from previous column
