Arlight SR-1009F Series User manual

RF wireless LED remote controller
Four zones/areas
Press-button RGB+W controller
Model:SR-2819S with SR-1009Fxx
Parameter
Wiring diagram
Product Size
Brief introduction of buttons
Product introduction
SR-2819S RGBW remote controller has 4 different zones. It can get Red/ Green/ Blue/ White color directly. The
remote controller can save up to 3 colors or 3 modes into corresponding buttons (S1,S2,S3) for each zone.
You can choose any color through color wheel. you can set the system as RGB 3-channeloutput, or RGBW 4-
channel output.
Receivers work with WIFI-RF converter to be controlled by smart phone
Part No. Input Voltage Remarks
Output Current
SR-1009FA 12-36VDC Constant voltage
4x(60-180)W
4x5A
Output Power
SR-1009EA 12-36VDC Constant voltage
4x(96-288)W4x8A
Remote
Part No. Operation Voltage DIMENSIONS
ø/h (mm)
Operation
Frequency
SR-2819S 4.5VDC 48x140x16
916.66MHz
Receiver
SR-1009FA3 12-36VDC Constant current
4x(4.2-12.6)W
4x350mA
SR-1009FA7 12-36VDC Constant current
4x(8.4-25.2)W4x700mA
Remarks
load 3pcs 7 AAA (1.5V)
batteries
Note:
One receiver can work with 1-8pcs SR-2819S
One SR-2819S control multiple receivers
The power supply chosen must be 20% higher than the actual load
Indicator: indicate the state of
remote control
White channel: the 4th channel
ON/OFF of all zones
4 zones: each zone can save
3 color or modes
Brightness: dim up
Brightness: dim down
S1 S2
S3
W
W+
Running button/Speed button ww nw and cw mixed by RGB
Save button
1)Receiver Connection Diagram for Single Unit
2) Connection Diagram for Multiple UnitsReceiver
Power Supply
12-36VDC
LN
110V-230VAC
whi te
SR-1009FA
LED CONTROLLER
1234
Lea rni ng Ke y
whi te
SR-1009FA
LED CONTROLLER
1234
Lea rni ng Ke y
whi te
SR-1009FA
LED CONTROLLER
1234
Lea rni ng Ke y
Power Supply
12-36VDC
LN
110V-230VAC
whi te
SR-1009FA
LED CONTROLLER
1234
Lea rni ng Ke y
Color wheel
55.0
17.0
120.0
5

Safety & Warnings
Warranty Agreement
1) The product shall be installed and serviced by a qualified person.
2) IP20.Please avoid the sun and rain. When installed outdoors, please ensure it is mounted in a water proof
enclosure.
3) Always be sure to mount this unit in an area with proper ventilation to avoid overheating.
4) Please check if the output voltage of any LED power supplies used comply with the working voltage of the
product.
5) Never connect any cables while power is on and always assure correct connections to avoid short circuits
before switching on.
6)
7) For update information please consult your supplier.
Please ensure that the cable is secured tightly in the connector
1) We provide lifelong technical assistance with this product:
5-year warranty. We print date on every products, for example :1125 means year 2011,week 25.The
warranty is for free repair or replacement and covers manufacturing faults only.
For faults beyond the 5-year warranty we reserve the right to charge for time and parts.
2) Limited Warrenty
Any defects caused by wrong operation.
Any damages caused by unauthorized removal, maintenance, modifying, incorrect connection and
replacement of chips.
Any damages due to transportation, vibration etc. after purchase.
Any damages caused by earthquake, fire, lightning, pollution and abnormal voltage.
Any damages caused by negligence, inappropriate storing at high temperatures and humidity or near
harmful chemicals.
Product has been updated
3) Repair or replacement as provided under this warranty is the exclusive remedy to the customer.
Operation
Learning (matching)
a. Do wiring according to connection diagram
b. Wake up the remote control by touching ON/OFF button.
c. Press learning button on receiver.
d. Touch any zone button on remote control.
e. Then touch color wheel.
f. Connected LED light will blink to confirm zone designation.
g. Press at learning button on receiver over 5 seconds until LED light flash, then delete the learned ID.
Note 1: To choose a master from slaves by jumper for each zone.
Short circuit for master.
Open circuit for slave.
Each zone only can set one master controller. After a period of time, the master will do synchronization
operation to keep the same color or mode of all slaves in one zone.
Note 2: Each remote control 4 zones (areas) receivers, each area can be learned as many receivers as
we can.
Each receiver maximally can be controlled by 8 different remote controllers.
Choose zone number , for example, and , then touch , choose the color you want,
zone 1 and 3 will indicate corresponding color as we touched.
Brightness Up & Down Button
Short/Long press button to dim down brightness of RGB channels, Short/long press button to dim
up RGB channels.
“W” channel is separated from RGB channels, so we can only long press button to dimming“W” channel.
Running Mode & Speed Button
a. Short press ,mode will run. Press it once, it runs one mode. Press button again, it stops, then press
one more time, it will enter next mode. There are total 10 build-in modes.
b. Long press when mode is running, Fist long press will speed up the color moving, long press again to
speed down the color moving.
Color wheel
W+ Button
a. RGB channel will mix to three different white: warm white, nature white and cold white by short press
For example: first press---warm white, press again---nature white, third press again—cold white, fourth
press—warm white………………
b. Fast click twice to switch off RGB channel.
W+
W+
Save and recall button
Save color: select zones from select a color from
long press one save button
from S1,S2,S3 for 2-3 second
LED lighting flash twice
indicate save successful
a.
b. Save running mold: select zones from select a moving mode from
long press one save button from
S1,S2,S3 for 2-3 second
LED lighting flash twice
indicate save successful
c. Recall: select zone button which we want recall from 1-4, then short press save button S1,S2,S3.

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by
manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.