Arp 984353 User manual

2D Wireless

Barcode Scanner

ARP 984353

855152

User’s Manual

FCC Compliance

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions manual, may cause

harmful interference to radio communications. Operation of this equipment

in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

Changes or modifications not expressly approved by the party responsible

for compliance could void the user‘s authority to operate the equipment.

Limited Warranty

No warranty of any kind is made in regard to this material, including, but not

limited to, implied warranties of merchantability or fitness for any particular

purpose. We are not liable for any errors contained herein or for incidental or

consequential damages in connection with furnishing, performance or use of

this material. We shall be under no liability in respect of any defect arising

from fair wear and tear, willful damage, negligence, abnormal working

conditions, failure to follow the instructions and warnings, or misuse or

alteration or repair of the products without written approval.

Table of Contents

1. INTRODUCTION……………………………………………………………………….3~4

2.I NSTALLATION………………………………………………………………………...5~7

3.SET UP FROM BAR CODE LABEL…………………………………………….…..…..8

Transmission Speed…….………………..……………………..…………….…9

Wireless Auto-commection.…………………………………………….……...9

Power-Saving Mode…………….…………………………………………..…….9

Battery Fully Charged Alarm….…………………………………………….…10

Low Battery Voltage Alarm….…………………………………………….…..10

Keyboard Country…….……….………………………………………………….11

Multi-Interface Functions….………………………………….……….…12~14

Symbologies On/Off………………………………………..……….....….15~19

Symbologies Set Up……………………………………………..……….…20~25

Termination String Setup Bar Codes………………………………….26~27

Introduction

Our 2D Wireless barcode scanner combines the best scanning performance

and value. The device provides an accurate, easy, and fast method of data

entry and data storage for computerized information systems. It is easy to

install and does not require Software or drivers to operate.

Our 2D Wireless barcode scanner is a powerful and reliable handheld scanner

without compromise.

All the operating parameters are programmed by bar code programming menu

and stored in non-volatile RAM which can retain the settings after power is

turned off.

Installation

Insert the plug on the free end of the Communications Cable into the

appropriate connector on the host as below described:

Cable Connection:

1. Please switch ON and charge scanner for 4~5 hours at first time before use,

scanner switch shown on Fig. 2.

2. After switch ON, the Orange LED will flash following with 3 beep-sounds. The RED

LED will be OFF while it links to cradle within 2.4GHz radio range.

3. If RED LED is continual ON, please re-plug USB cable, then, scan the 3 barcodes

on the bottom of cradle sequentially. (Shown on Fig. 3 from 1 to 3). If you are

unable to complete this setting within 1 minute, please re-plug USB cable & re-start

the scanner, and try again.

4. Charging issue: Cradle works as charger when putting scanner on it. Even if the

scanner's battery is full, the cradle will continue to supply power to the scanner.

We suggest you to remove scanner from cradle when scanner is charged fully.

Indicator Information

Orange continual ON Full charged

Orange LED Flash Charging / Low battery

Red LED Continual ON Off line / out of service

Green LED ON Good read

When the battery voltage is too low, the Orange LED will flash and with one

beep sound. Please charge it immediately before the machine mandatorily

shutdown. When it shutdown, please full charge then repower on scanner.

When OFF line/ out of service the 2D Engine will OFF and scanner will not work.

Under power-saving mode, there will not be LED indication

Reset Configuration to Defaults

If you are unsure of the scanner configuration or have scanned the

incorrect codes, please scan the following three barcodes. This will reset

the scanner to its factory defaults.

Tip

Do not hold the scanner directly over a barcode at 90˚. Scanning light

bounces directly back into the scanner from the barcode label is known as

specular reflection which will create a "dead zone" where decoding is

difficult. Practice a few times to find what range of angles works best.

Maintenance

Cleaning the scan window is the only maintenance required. Adirty

window may affect scanning accuracy.

Wipe the scanner window gently with a lens tissue or other material suitable

for cleaning optical material.

Do not spray water or other cleaning liquids directly onto the window.

Setup from Bar Code Label

ransmission Speed

High-speed transmission for PC uses.

Slow-speed transmission for PC use (Default).

Wireless Auto-connection

Wireless Auto-connection ON: When out of range, it

will keep trying to connect to device.

Wireless Auto-connection OFF: When out of range, it

will stop auto-connecting after sending signal for

connecting twenty times. When back to the range,

kindly presses trigger to connect to the device

(Default).

Powe

-Saving Mode

Power-Saving Mode can extend the usage time of battery. There are 5

modes can be chosen. When Scanner goes into Power-Saving Mode, user

can press "SCAN/Trigger" button, it will wake up and begin to scan.

Power-saving mode OFF

Enter power-saving mode after no usage

for 1 minute (Default)

Enter power-saving mode after no usage

for 5minute

Enter power-saving mode after no usage

for 15 minute

Enter power-saving mode after no usage

for 30 minute

When in charging, scanner will not enter power-saving mode automatically.

Battery Fully Charged Alarm

OFF (Default)

Low Battery Voltage Alarm

ON (Default)

OFF

Under power-saving mode, there will not be LED indication when in charging.

Keyboard Country (For USB HID only)

Scan the appropriate country code below to program the

keyboard for your country or language. As a general rule, the

following characters are not supported by the scanner for

countries other than the United States: @ | $ # { } [ ] = / ‘ \ <

> ~

USA (Original setting)

Italian

Norway

France

Germany

Vietnam

Sweden

Spain

Denmark

Portugal

Switzerland

Hungary

** Code Programming ON

(Pro CMD : 0006010)** Code Programming OFF

(Pro CMD : 0006000)

Multi-Interface Functions

Save as User Default

(Pro CMD : 0001150)

Load User Default SAVED

(Pro CMD : 0001160)

Operating settings

Trigger Mode

Auto-Sensing

Pro CMD : 0302000 Pro CMD : 0302010

** Code Programming ON

(Pro CMD : 0006010)** Code Programming OFF

(Pro CMD : 0006000)

Normal Sensitivity (= 11) Sensor

Mode High Sensitivity (= 8)

Pro CMD : 0312010 Pro CMD : 0312020

Enhanced Sensitivity (= 5) Low Sensitivity (= 14)

Pro CMD : 0312030 Pro CMD : 0312000

** Code Programming ON

(Pro CMD : 0006010)** Code Programming OFF

(Pro CMD : 0006000)

Allow Reading All = enable to read

all symbologies and programming

codes

Prohibit ReadingAll = allow reading

programming codes only.

Pro CMD : 0001020 Pro CMD : 0001010

Allow Reading All 1D Prohibit Reading All 1D

Pro CMD : 0001040 Pro CMD : 0001030

Allow Reading All 2D Prohibit Reading All 2D

Pro CMD : 0001060 Pro CMD : 0001050

** Code Programming ON

(Pro CMD : 0006010)

** Code Programming OFF

(Pro CMD : 0006000)

1D Symbologies On/Off – 1

CODE 39 ENABLE CODE 39

CODE 39 DISABLE

Pro CMD : 0408020 Pro CMD : 0408010

ENABLE * Sign DISABLE * Sign

CODE 93

Pro CMD: 0408090 Pro CMD: 0408080

CODE 93 - ENABLE CODE 93 - DISABLE

Pro CMD : 0410020 Pro CMD : 0410010

CODE 128 - ENABLE CODE 128 CODE 128 - DISABLE

Pro CMD : 0400020 Pro CMD : 0400010

CODABAR - ENABLE CODABAR CODABAR - DISABLE

Pro CMD : 0409020 Pro CMD : 0409010

INTERLEAVED 25 -

ENABLE INTERLEAVED

25 INTERLEAVED 25 -

DISABLE

Pro CMD : 0405020 Pro CMD : 0405010

** Code Programming ON

(Pro CMD : 0006010)** Code Programming OFF

(Pro CMD : 0006000)

1D Symbologies On/Off – 2

UPC-A ENABLE UPC/EAN UPC-A DISABLE

Pro CMD : 0404020 Pro CMD : 0404010

UPC-E ENABLE UPC-E DISABLE

Pro CMD : 0403020 Pro CMD : 0403010

EAN-8 ENABLE EAN-8 DISABLE

Pro CMD : 0401020 Pro CMD : 0401010

EAN-13 ENABLE EAN-13 DISABLE

Pro CMD : 0402020 Pro CMD : 0402010

EAN-128 ENABLE UCC/EAN EAN-128 DISABLE

Pro CMD : 0412020 Pro CMD : 0412010

ENABLE Industrial 25 DISABLE

Pro CMD: 0417020 Pro CMD: 0417010

** Code Programming ON

(Pro CMD : 0006010)** Code Programming OFF

(Pro CMD: 0006000)

1D Symbologies On/Off – 3

Pro CMD : 0420020 Pro CMD : 0420010

Code 11 ENABLE Code 11 Code 11 DISABLE

Pro CMD : 0415020 Pro CMD : 0415010

ISBN ENABLE ISBN ISBN DISABLE

Pro CMD : 0416020 Pro CMD : 0416010

ENABLE

UCC/EAN

Composite DISABLE

Pro CMD : 0414020 Pro CMD : 0414010

** Code Programming ON

(Pro CMD : 0006010)** Code Programming OFF

(Pro CMD : 0006000)

2D Symbologies On/Off - 1

Data Matrix -ENABLE Data Matrix

Data Matrix -DISABLE

Pro CMD : 0504020 Pro CMD : 0504010

**Forward Direction

Barcode Only Both

Pro CMD: 0504320 Pro CMD:0504322

Backward Direction

Barcode Only

Pro CMD : 0504321

QR Code -ENABLE QR Code

QR Code -DISABLE

Aztec -ENABLE Aztec

Aztec -DISABLE

Pro CMD : 0503020 Pro CMD : 0503010

** Code Programming ON

(Pro CMD : 0006010) ** Code Programming OFF

(Pro CMD : 0006000)

2D Symbologies On/Off - 2

PDF 417ENABLE PDF 417

PDF 417 DISABLE

Pro CMD : 0501020 Pro CMD : 0501010

**Forward Direction Barcode

Both

Pro CMD:0501320 Pro CMD:0501322

Backward Direction Barcode

Pro CMD:0501321

This manual suits for next models

Table of contents

ARP 984353 User manual

Popular Barcode Reader manuals by other brands