Arrow Storage Products EPA104 Instructions for use

Gloves must be worn
at all times to reduce
risk of injury!
Owner’s Manual
& Assembly Guide
731841021
BUILDING DIMENSIONS
* See Inside for Detailed Safety Information.
Size rounded off to the nearest foot For proper base construction see page 11
†
Nominal Size
10’ x 4’
EN-01KR
†
Base
Size
Exterior Dimensions
(Roof Edge to Roof Edge)
Width Depth Height
Interior Dimensions
(Wall to Wall)
Width Depth Height
Door
Opening
Width Height
Approx.
Size
Storage
Area
10’ x 4’ 35 Sq. Ft. 188 Cu. Ft. 123 1/2” 47” 67 3/4” 118 1/4” 42 1/2” 66 9/16” 55 1/2” 60”
3,0m x 1,2m 3,3m25,3m3313,7 cm 119,4 cm 172,1 cm 300,4 cm 108,0 cm 169,1 cm 141,0 cm 152,4 cm
†
121” x 45 1/4”
307,3 cm x 114,9 cm
ShelterLogic.com
/
product-registration
Register • Enregistrer • Regístrate
Steel ShedSteel Shed
arrowsheds.com
Visit our website for compatible accessories
Model No. EPA104

2
• Keep children and pets away from the worksite during construction and until the building is completely assembled. This will
help avoid distractions and any accidents which may occur.
EN-04HN
• Care must be taken when handling various pieces of your building since many contain sharp edges.
CAUTION
• Do NOT attempt to assemble your building before double checking that you have all the parts indicated in the parts lists.
Any building left partially assembled may be seriously damaged by even light winds.
• Do NOT attempt to assemble your building on a windy day. The large panels can catch the wind like a “sail”, making
construction diffi cult and unsafe.
• NEVER concentrate your weight on the roof of the building.
Watch the Weather Closely
• Before assembling any parts, your base should be constructed and an anchoring system should be ready to use.
Your building MUST be anchored to prevent wind damage.

3
EN-05HN
• The best location is a level area with good drainage.
ASSEMBLY
• Allow enough space outside the building to be able to access the roof with a ladder.
• Use Teamwork: Two or more people are required to assemble your building.
CARE & MAINTENANCE
• DO NOT use power washing to clean your shed.
• Combustibles and corrosives must be stored in air tight containers designed for chemical and/or combustible storage.
Corrosive chemicals such as fertilizers, pesticides and herbicides should be cleaned off the interior and exterior surfaces
immediately. Rust caused by chemical damage is not covered by the warranty.
Rust protection precautions
• Avoid nicking or scraping the coating surface, inside and out.
• Keep roof, base perimeter and door free of debris.
• Touch up scrapes or nicks and any area of visible rust as soon as possible.

4
HARDWARE LIST EN-05IO
The fasteners used in each step are shown actual size at the top of each page. If you are unsure which
fastener to use, hold it up to the picture and use the one that matches.
165103 Hex Nut (#8-32) 61
Key
No. Part No. Part
Description Qty. Part Views
265923 Small Bolt (#8-32 x 3/8) (10 mm) 61
365004 Small Screw (#8AB x 5/16) (8 mm) 260
465900 Black Screw (#10B x 1/2) (13 mm) 8
565109 Acorn Nut (#8-32) 4

5
HARDWARE LIST EN-05KR
12
30028 Nameplate 1
666045 Handle 2
766769 Door Slide 4
866646 Washer Sheet 8
966382 Lower Door Guide 4
10 66183L Left Roof Trim Cap 2
11 66183R Right Roof Trim Cap 2
13 66775 2 Plug (Door Color)
Key
No. Part No. Part
Description Qty. Part Views

6
6
14 11569 2
16 8934 Ramp 1
17
23
11572 Side Wall Angle 2
25
11573 Rear Wall Angle 2
26
15 8936 Rear Floor Frame 2
22 9917 Rear Wall Channel 2
EN-06KR
PARTS LIST
9367 Front Floor Frame 2
11574 2
24 9365 2Wall Channel Front
27 9369 2
Door Jamb
Side Floor Frame
Side Wall Channel
6514 Corner Panel 2
18
9373 2
19 Wall Panel
21 6515 Wall Panel 4
11570 Corner Panel 2
20
Key
No. Part No. Part
Description Qty. Part Views

7
33 11576 Roof Beam 2
36 11578 Roof Panel 4
37 10872 Roof Trim 2
31 10562 Right Gable 1
32 80015 Left Gable 1
EN-07KR
30 11575 2
PARTS LIST
Front Header
39 80253 2
Door Panel
40 6278 Vertical Door Channel 2
41 10497 4
29 9366 2
Door Track
28 6403 Door Track Splice 1
34 11577 Right Roof Panel 1
35 80289 Left Roof Panel 1
38 80087 Roof Trim 2
Horizontal Door Brace
Key
No. Part No. Part
Description Qty. Part Views

6
8
EN-09IO
PARTS LIST
42 3719 2
Door Handle Brace
Key
No. Part No. Part
Description Qty. Part Views

6
9
EN-10IO
ASSEMBLY BY KEY NO.
14
14
15
15
16
17
17
18
18
19
21
21
21
21
22
23
19
23
24
25
25
26
26
27
27
28
20
20
22
24
29
29
30
30

10
EN-11IO
ASSEMBLY BY KEY NO.
34
36
35
33
33
38
38
31
36
36
36
37
37
40
41
39
40
41
39
41
41
42
42
32

6
11
EN-12IO
CONSTRUCTING A FOUNDATION
Wood Platform Concrete Slab
16"/24"
40,6 cm/61,0 cm
121”
307,3cm
45 1/4"
114,9cm
*IMPORTANT *
The base MUST be fl at and level to provide adequate support for your building, otherwise the PRE-DRILLED HOLES WILL
NOT ALIGN AND IT CANNOT BE ASSEMBLED. No matter which of the options below you choose for a base, an ARROW
ANCHORING KIT is recommended as an eff ective method of properly securing your building after assembly is complete.
OPTION 1: Build directly on the ground
OPTION 2: Wood Platform
NOTE: Pressure Treated Lumber must NOT be used where it will make contact with your storage building. The properties of Pressure
Treated Lumber will cause accelerated corrosion. If Pressure Treated Lumber comes in contact with your storage building your
warranty will be voided. The platform should be level and fl at (free of bumps, ridges, etc.) to provide good support for the building.
The necessary materials may be obtained from your local lumber yard.
OPTION 3: Concrete Slab
The slab should be at least 4" (10,2 cm) thick.
121”
307,3cm
45 1/4"
114,9cm

12
8936
119 3/8” 303,2 cm
11 7/8” 30,2 cm
EN-14IF
1: FLOOR FRAME
Overlap Length Finished Length
8936 2
8936
9367 2
65923 65103 565004 8
65923 65103
8934
6592365103
9367
8934
9367
8934 1
Finished Length
119 3/8” 303,2 cm
Front
65004

12
EN-15IO
13
11569
1: FLOOR FRAME
65004 88936+8936 1(2)9367+8934 111569 2
11569
8936
8936
9367
8934
NOTES:
Do NOT fasten your Floor Frames to your
Base at this time. You will anchor your
building after it is erected.
The Floor Frame must be BOTH square AND
level or the holes will not line up properly.
Measure diagonally from corner to corner.
When diagonal measurements are equal,
the Frame is square.
X4
65004
9367 11569
8936
9367
11569
X2
65923 65103 2
65103
65923

14
EN-16IO
118 1/8” (300,0 cm)
Finished Length
11573
2: PRE-ASSEMBLY
65923 65103 211573 29917 2
65923
65103
11573
9917
65923
65103
9917
118 1/8” (300,0 cm)
Finished Length

15
EN-17IO
2: PRE-ASSEMBLY
65923 65103 8
65923
11576
65103
11576 2
11576
11576
11576
65103
65103
65923
65923
119 7/8” (304,5 cm)
Finished Length

16
EN-19IB
2: PRE-ASSEMBLY
9366
65004 49366 26403 1
Painted Part
9366
6403
118 1/8” (300,0 cm)
Finished Length
CORRECT INCORRECT
Long Leg
on top.
Door Slide
END VIEW
65004
66769
To remove or install Door Slides:
• Remove Doors from Slides and set aside.
• Using pliers, bend down a corner of the Door Track.
• Remove or install Door Slides.
• Carefully bend the corner back into position.
Slides should be installed in Door Track prior to installation. However, if this step is overlooked
or if the Slides need to be removed for maintenance, the following procedure may be used.
66769 4

17
EN-19IO
2: PRE-ASSEMBLY
65923
11575
65103
11575 2
11575
11575 65004
9366
65923 66646 65103 265004 10 (2)9366+6403 1
9366
6403
11575
66646
9366
Long Leg on Top.
Short Leg on Bottom.

18
EN-18KR
3: CORNER PANELS
65004 66646 86514 2
65923 66646 65103 4
65004
66646
65923
65103
66646
9373
6514
65004
66646
65923
65103
66646
X2
6515 2
11570
6515
X2
9373 2
11570 2

19
EN-19KR
3: CORNER PANELS
65004 66646 34 6514+9373 2
65004
66646
Front
9373
6515+11570 2
9373
6514
6514
11570
11570
6515
6515
66646
65923 66646 65103 2
65923
65103

20
EN-22IO
4: WALL ANGLE
65004 66646 24 11572 2
11573+11573
11572 66646
Front
11573+11573 1
65004
11572 11573
11572