Arrow Storage Products GRF1210CST Instructions for use

Customer Service:
1-800-851-1085 or
[email protected]
BUILDING DIMENSIONS
Gloves must be worn
at all times to reduce
risk of injury!
Size rounded off to the nearest foot
Owner’s Manual
& Assembly Guide
729280719
†
Exterior Dimensions
(Roof Edge to Roof Edge)
Width Depth Height
Interior Dimensions
Width Depth Height
Door
Opening
Width Height
Approx.
Size
Storage
Area
†
3,7 m x 3,0 m 10,8 m 29,5 m 371,2cm 313,8 cm 313,6 cm 358,5 cm 300,5 cm 310,5 cm 71,9 cm 199,0 cm
(Roll Up Door)
241,3 cm 212,5 cm
12' x 10' 116 Sq. Ft. 1043 Cu. Ft. 146.13" 123.56" 123.48" 141.13" 118.30" 122.23" 28.30" 78.35"
(Roll Up Door)
95.00” 83.66”
23
Additional
per Extension
142.13” x 60”
361,0 cm x 152,4 cm
Base
Size
142.13” x 119.25”
361,0 cm x 302,9 cm
Each Extension adds an additional 60” (152,4 cm) in length, 59 Sq. Ft. (5,4 m2)
additional storage area, and 529 Cu. Ft. (15,0 m3) additional storage volume.
* See Inside for Detailed Safety Information.
Model No. GRF1210CST
GRF1220CST
01HJ

1DLQWHUQHWHMHNGLVSR]tFLLQiYRGQD]RVWDYHQLHYćDOãtFKMD]\NRFK1iYRGNPRQWiåLYGDOãtFKMD]\FtFKMHNGLVSR]LFLYRQOLQHYHU]L3ĜtVWXS]tVNiWHSRQDVNHQRYiQt45NyGXQtåH$]|VV]HV]HUHOpVL~WPXWDWyWRYiEELQ\HOYHNHQLVHOpUKHWĘRQOLQHȊʌȐȡȤİȚįȚĮșȑıȚȝȠıIJȠįȚĮįȓțIJȣȠIJȠİȖȤİȚȡȓįȚȠıȣȞĮȡȝȠȜȩȖȘıȘȢıİʌİȡȚııȩIJİȡİȢȖȜȫııİȢȈĮȡȫıIJİIJȠȞʌĮȡĮțȐIJȦțȫįȚțĮ45ȖȚĮȞĮĮʌȠțIJȒıİIJİʌȡȩıȕĮıȘP/N 6PP722621216
GB: Assembly manual in additional languages available online.
Scan QR code below to access.
FR: Manuel de montage disponible en ligne dans d’autres langues.
Pour y accéder, scannez le code QR ci-dessous.
DE: Montageanleitung in zusätzlichen Sprachen online verfügbar.
Scannen Sie den QR-Code unten, um darauf zuzugreifen.
IT: Manuale dell’assemblea in altre lingue disponibile online.
Per accedere effettua la scansione del codice QR in basso.
DT: Samlingshåndbog i yderligere sprog til rådighed online.
Scan QR kode nedenunder for at få adgang.
SK: Na internete je k dispozícii návod na zostavenie v ďalších jazykoch.
Dostanete sa k nemu naskenovaním kódu QR.
CZ: Návod k montáži v dalších jazycích je k dispozici v online verzi.
Přístup získáte po naskenování QR kódu níže.
DE: Monteringsmanual på ytterligare språk tillgängliga online.
Skanna QR-kod nedan för att komma åt.
RM: Manualul de asamblare în alte limbi disponibile online.
Scanați codul de mai jos pentru a accesa.

3
SAFETY & MAINTENANCE
Safety precautions MUST be followed at all times throughout the construction of your building!
Care must be taken when handling
various pieces of your building since
many contain sharp edges. Please
wear work gloves, eye protection and
long sleeves when assembling or
performing any maintenance on your
building.
Practice caution with the tools being
used in the assembly of this building.
Be especially familiar with the
operation of all power tools.
Keep children and pets away from the
worksite during construction and until
the building is completely assembled.
This will help avoid distractions and
any accidents which may occur.
NEVER concentrate your weight on
the roof of the building. When using
a step ladder make sure that it is
fully open and on even ground before
climbing on it.
Do NOT attempt to assemble your
building on a windy day. The large
panels can catch the wind like a “sail”,
causing them to be whipped around
making construction difficult and
unsafe.
Do NOT attempt to assemble your
building before double checking that
you have all the parts indicated on the
parts list as well as all hardware. Any
building left partially assembled may be
seriously damaged by even light winds.
IMPORTANT NOTE ON
ANCHORING
• Your building MUST be anchored to
prevent wind damage. See anchoring
page for more info.
• You must also have a temporary
anchoring system in place in case you
need to take a break from assembly.
03GW
Exterior Care:
For a long lasting finish, clean the exterior surface. We recommend washing with a mild soap solution. DO NOT use power washing to clean
your shed.
Combustibles and corrosives must be stored in air tight containers designed for chemical and/or combustible storage. Corrosive chemicals
such as fertilizers, pesticides and herbicides should be cleaned off the interior and exterior surfaces immediately. Rust caused by chemical
damage is not covered by the warranty.
Rust protection precautions may help to stop rust from developing, or stop it quickly as soon as it appears.
• Avoid nicking or scraping the coating surface, inside and out.
• Keep roof and base perimeter free of debris and leaves which may accumulate and retain moisture. These can do double damage since
they give off acid as they decay.
• Touch up scrapes or nicks and any area of visible rust as soon as possible. Make sure the surface is free of moisture, oils, dirt or grime and
then apply an even film of high quality touch-up paint.
• Various paint manufacturers provide products for rust treatment and coverage. If surface rust does appear on your shed we recommend
treating those areas as soon as possible, following the paint supplier of your choice instructions.
• Our customer service department can provide the paint tinting formula for matching the color of your shed. We also have touch-up paint
available for repairing small nicks and scratches.
Roof: Keep the roof clear of leaves and snow. Heavy amounts of snow on the roof can damage the building making it unsafe to enter.
Fasteners: Regularly check fasteners and retighten as necessary.
General: Wash off inked part numbers on coated panels with soap and water.
Please note, Manufacturer cannot be held responsible for any consequences due to buildings that are not installed per these instructions, or
for damage due to weather conditions or acts of God.
Keep these assembly instructions and owner’s manual for future reference.

4
ASSEMBLY TIPS &TOOLS
How to Select and Prepare Your Building Site: Before you start to assemble your
building, you will want to decide on a good location. The best location is a level area with good drainage.
• Allow enough working space so it is not difficult to move parts into position for assembly. Also, there needs to be enough
space outside the building to be able to fasten the panel screws from the outside.
• Before assembling any parts, your base should be constructed and an anchoring system should be ready to use.
Watch the Weather Closely: Be sure the day you choose to install your building is dry and calm.
Do NOT attempt to assemble your building on a windy day. Be careful on wet or muddy ground.
Use Teamwork: Two or more people are required to assemble your building. One person can hold
the parts or panels in place while the other person fastens them together and handles the tools. This
makes the process of assembling your building faster and safer.
Tools and Materials: Here is a list of some basic tools and materials you will need to assemble
your building. Decide which method of anchoring and the type of base you will use to make a complete
list of the materials you will need.
• Work Gloves
• Safety Glasses
• Nut Driver or Wrench
• Step Ladder 8’
• Power Drill (Cordless, Variable Speed)
• Pliers
• Utility Knife or Scissors
• Carpenter’s Level
• Tape Measure
• Clamp
• Spray Lubricant
• Square
• String (for squaring the frame)
• Awl (to align holes)
• Lumber and/or Concrete
• Hammer and Nails
• Spade or Shovel
• Hand Saw or Power Saw
RECOMMENDED TIME SAVERS
BASE PREPARATION TOOLS
07BQ
WHAT YOU NEED

3
Base
05GW
The Base For Your Building
Concrete Slab
The slab should be at least 4" (10,2 cm) thick. It must be level and flat to provide good support for the frame.
The following are the recommended materials for your base.
2 x 4's (38 mm x 89 mm) (will be removed once the concrete cures)
Concrete Sheet of 6 mil plastic
We recommend for a proper strength concrete to use a mix of:
1 part cement 3 parts pea sized gravel 2 1/2 parts clean sand
Prepare the Site/Construct a Base
1. Dig a square, 6" (15,2 cm) deep into the ground (remove grass).
2. Fill up to 4" (10,2 cm) in the square with gravel and tamp fi rm.
3. Cover gravel with a sheet of 6 mil plastic.
4. Construct a wood frame using four planks of 2x4 (38 mm x 89 mm)
lumber.
5. Pour in concrete to fi ll in the hole and the frame giving a
total of 4" (10,2 cm) thick concrete. Be sure surface is level.
Allow 3 - 5 hours for construction and a week for concrete curing time.
Note: Before beginning construction, check local building codes
regarding footings, location and other requirements.
119.25" 302,9 cm
Add'l 60" 152,4 cm
per extension
Note: Finished Slab dimensions, with lumber removed.
Reinforcing
Rods
Reinforcing
Rods
Optional Footer Type of Foundation
Welded Wire
Fabric
142.13"
361,0 cm
FRONT (ROLL-UP DOOR)
5

3
Anchoring
06GW
6
It is important that the entire floor frame be anchored after the building is erected.
Below are recommended ways of anchoring.
Anchoring Down The Building
Anchoring into Concrete:
For poured concrete slab or footing or patio blocks:
Use 1/4" x 2" (6 mm x 51 mm) Lag Screws.
Anchoring into Wood:
Use 1/4" (6 mm) Wood Screws. There are 1/4" (6 mm)
dia. holes provided in the frames for proper anchoring.

17
HARDWARE LIST...
07HJ
7
1
Hardware Views by Key No.
13
19
8, 9, 107
1 65103 Hex Nut (#8-32) 18
265101 Square Nut (1/4-20) 10
3 65106 Square Nut (#10-32) 240
4 65943 Bolt (Bare) (#10-32 x 7/16) (10 mm) 140
5 65943 Bolt (Wall Color) (#10-32 x 7/16) (10 mm) 64
6 65943 Bolt (Roof Color) (#10-32 x 7/16) (10 mm) 36
7 66783 Flathead Bolt (#8-32x1/2) 18
8 66611 Tapping Screw (Bare) (#10AB x 1/2) (13 mm) 244
9 66611 Tapping Screw (Wall Color) (#10AB x 1/2) (13 mm) 380
10 66611 Tapping Screw (Roof Color) (#10AB x 1/2) (13 mm) 246
11 65989 Hex Head Bolt (#1/4-20x1/2) 10
12 65020 Flat Washer 8
13 66646 Washer Sheet 18
14 6228 Track Support 2
15 60H Corner Cap 4
16 30026 Peak Cap 2
17 30005 VHB Tape 1
18 30018 Alcohol Wipe Packet 2
19 66609 Hinge 3
20 7003 Left Shear Plate 6
21 7004 Right Shear Plate 6
22 7022 Eave Bracket 4
Key
No.
Part
No.
Part
Description Qty.
List
4, 5, 6
The fasteners used in each step are shown
actual size at the top of each page. If you
are unsure which fastener to use, hold it up
to the picture and use the one that matches.
15
20
7003
3 65106 Square Nut (#10-32) 44
465943 Bolt (Bare) (#10-32 x 7/16) (10 mm) 34
6 65943 Bolt (Roof Color) (#10-32 x 7/16) (10 mm) 10
8 66611 Tapping Screw (Bare) (#10AB x 1/2) (13 mm) 140
9 66611 Tapping Screw (Wall Color) (#10AB x 1/2) (13 mm) 90
10 66611 Tapping Screw (Roof Color) (#10AB x 1/2) (13 mm) 128
13 66646 Washer Sheet 6
14 6228 Track Support 2
20 7003 Left Shear Plate 6
21 7004 Right Shear Plate 6
22 7022 Eave Bracket 4
Key
No.
Part
No.
Part
Description
Qty.List
21
7004
Extension 1205M
2 3
11 12
14 16
17 18
22
BB - Bare Bolt
WB - Wall Bolt
RB - Roof Bolt
BS - Bare Screw
WS - Wall Screw
RS - Roof Screw
N - Nut
W - Washer

6
PARTS LIST...
8
08GW
Assembly Part Part Extension
Key No. Number Description C1 C2 C3 1205M
1 6372 Gable Strut 42
2 6380 Gable Brace Outer 4
3 6381 Gable Brace Mid 4
4 6382 Gable Brace Center 2
5 7942 Right Gable 2
6 7943 Left Gable 2
7 11149 Ridge Beam 12
8 11150 Right Rear Frame 2
9 11151 Frame, Side Floor 2
10 11152 Channel, Side Wall 2
11 11153 Panel, Wall Corner Narrow 4
12 11154 Ridge Beam 6
13 11155 Floor Side Frame 2
14 11156 Corner Support Structural 8
15 11157 Panel, Wall Full 10 4
16 11158 Frame, Front Floor 3
17 11159 Channel, Side Wall 2
18 11160 Panel, Wall Half 1
19 11161 Header Angle 2
20 11162 Channel, Header 2
21 11163 Channel, Mid Wall 2
22 11165 Channel, Mid Wall 2
23 11166 Panel, Wall Half 3 2
24 11168 Panel, Wall Corner 4
25 11169 Panel, Wall Half 1
26 11170 Panel, Wall Full 1
27 11171 Panel, Jamb Left 1
28 11172 Panel, Wall Full 4
29 11173 Panel, Wall Half 1
30 11174 Panel, Roof Full 8 4
31 11175 Panel, Roof Half 2
32 11176 Channel, Side Door 1
33 11177 Door Stop 2
34 11178 Panel, Roof Corner Right 2
35 11179 Column, Front 2
Con rm that all hardware and parts are present before attempting to assemble
your Storage Unit.
Customer Service:
1-800-851-1085 or [email protected]
For missing or damaged parts contact Customer Service. Do not return to store.

6
PARTS LIST...
9
09GW
Assembly Part Part Extension
Key No. Number Description C1 C2 C3 1205M
36 11180 Frame, Rear Right 1
37 11181 Header Angle Side 1
38 11182 Panel, Jamb Right 1
39 11183 Track Strut 2
40 11184 Frame, Side 1
41 11185 Panel, Jamb Right 1
42 11186 Truss, Column 3 2
43 11187 Chord, Truss Upper 2 2
44 11188 Chord, Truss Lower 2 2
45 11189 Chord, Truss Lower 1 1
46 11190 Chord, Truss Vertical 2 2
47 11191 Chord, Truss Upper 2 2
48 11192 Chord, Truss Diagonal 2 2
49 11193 Panel, Door 1
50 11195 Door Brace, Vertical 2
51 11196 Channel, Door Horizontal 2
52 11197 Support, Door Track 4
53 11200 Panel, Door Back 1
54 11201 Lintel 1
55 11202 Ridge Cap Outside 2
56 11203 Trim, Side Roof Inside 2
57 11204 Trim, Side Roof Outside 4
58 11205 Ridge Cap Inside 1
59 11207 Panel, Wall Half 1
60 11290 Support, Right Track 1
61 11291 Lintel 1
62 11292 Ramp 1
63 30002 Handle, Side Door Assembly 1
64 80141 Frame, Side Floor 2
65 80143 Channel, Side Wall Left 2
66 80145 Frame, Front Floor Left 3
67 80147 Channel, Mid Wall Left 1
68 80149 Frame, Rear Left 1
69 80151 Panel, Roof Corner Left 2
70 80153 Panel, Jamb Left 1
71 80159 Left Rear Frame 2
72 80161 Panel, Wall Half 1
73 80191 Support, Left Track 1

17
Components for Garage Door (GD)
10GW
10
Door Section with
weather stripping
#1 End Hinge #3 End Hinge
#2 End Hinge
#1 Center Hinge
Door Lock
Assembly
Top
Fixture
Bottom
Fixture Right
Bottom
Fixture Left
Roller
Inside Step
Plate
Door Section
222
313
11
1 1 2
10