ARTE SOL 60 Instruction Manual

Table of Contents
1. Arte®Fireplace - A Greek Quality Product................................................................................................................................................................. 2
2. Facts About Wood and the Environment................................................................................................................................................................... 2
2.1. Why use wood?...................................................................................................................................................................................................................... 2
2.2. Buying firewood...................................................................................................................................................................................................................... 2
2.3. Storing your wood .................................................................................................................................................................................................................. 2
2.4. Wood types and calorific value .......................................................................................................................................................................................... 3
2.5. Determining the heat output ............................................................................................................................................................................................... 4
3. Endorsements & Certifications ..................................................................................................................................................................................... 5
3.1. Endorsement........................................................................................................................................................................................................................... 5
3.2. Declaration of Performance CE .......................................................................................................................................................................................... 5
3.3. Features marking plate ......................................................................................................................................................................................................... 5
4. Packaging ....................................................................................................................................................................................................................... 5
4.1. Unpacking............................................................................................................................................................................................................................... 5
5. Assembly.......................................................................................................................................................................................................................... 6
5.1. Door opening side change .................................................................................................................................................................................................. 6
5.2. Electrical installation .............................................................................................................................................................................................................. 7
5.3. Revolving buffer installation.................................................................................................................................................................................................. 7
5.4. Fixing the handle.................................................................................................................................................................................................................... 7
6. Fire Safety ........................................................................................................................................................................................................................ 7
6.1. Safe distances......................................................................................................................................................................................................................... 7
6.2. Wooden beams protection.................................................................................................................................................................................................. 7
6.3. General security instructions................................................................................................................................................................................................. 8
6.4. Flue security instructions ........................................................................................................................................................................................................ 8
6.4.1. Basic requirements for proper flue operation ............................................................................................................................................................... 8
6.4.2. Chimney placement......................................................................................................................................................................................................... 8
6.4.3. Chimney cap..................................................................................................................................................................................................................... 9
6.4.4. Connecting the fireplace with the flue ....................................................................................................................................................................... 10
6.4.5. Air supply to adjacent rooms ........................................................................................................................................................................................ 10
6.4.6. Malfunction - Secure fireplace shutdown ................................................................................................................................................................... 11
7. Operating Instructions.................................................................................................................................................................................................. 11
7.1. Before initial use of an ARTE® SOL fireplace .................................................................................................................................................................... 11
7.2. About ARTE® SOL fireplace ................................................................................................................................................................................................ 11
7.3. General information ............................................................................................................................................................................................................ 12
7.3.1. When the fireplace paint dries...................................................................................................................................................................................... 12
7.3.2. Incineration preparation ................................................................................................................................................................................................ 12
7.3.3. Combustion air intake .................................................................................................................................................................................................... 12
7.3.4. Power failure .................................................................................................................................................................................................................... 13
7.3.5. Heating during seasonal change or in adverse weather conditions...................................................................................................................... 13
7.4. Use of the electronic control panel................................................................................................................................................................................... 14
8. Lighting the Fireplace .................................................................................................................................................................................................. 15
8.1. Traditional method of lighting ............................................................................................................................................................................................ 15
8.2. Lighting without CO emissions (FROM TOP TO BOTTOM)................................................................................................................................................ 15
9. Tertiary Combustion (Patented)................................................................................................................................................................................. 16
10. Cleaning & Maintaining the Fireplace.................................................................................................................................................................... 17
10.1. External maintenance....................................................................................................................................................................................................... 17
10.2. Internal maintenance........................................................................................................................................................................................................ 17
10.2.1. Ash disposal...................................................................................................................................................................................................................... 17
10.2.2. Glass .................................................................................................................................................................................................................................. 17
10.2.3. Gasket............................................................................................................................................................................................................................... 18
10.2.4. Internal parts that need maintenance ........................................................................................................................................................................ 18
10.3. Cleaning the fireplace and the flue ............................................................................................................................................................................... 18
10.3.1. Chimney sweeping ......................................................................................................................................................................................................... 18
10.3.2. Annual maintenance ..................................................................................................................................................................................................... 18
10.3.3. How to clean the inside parts of ARTE® SOL fireplace .............................................................................................................................................. 19
10.4. Internal parts removal ....................................................................................................................................................................................................... 19
10.5. Inactive fireplace for prolonged periods ....................................................................................................................................................................... 20
11. Tips & Tricks for Resolving Issues................................................................................................................................................................................ 20
12. Dimensions................................................................................................................................................................................................................... 21
13. Technical Specifications............................................................................................................................................................................................ 22
14. Warranty ...................................................................................................................................................................................................................... 23
14.1. Warranty terms ................................................................................................................................................................................................................... 23
14.2. Excluded from the warranty............................................................................................................................................................................................. 23
14.3. Responsibility....................................................................................................................................................................................................................... 23
14.4. Emergency maintenance................................................................................................................................................................................................. 23
14.5. Responsibility for installation ............................................................................................................................................................................................. 23
14.6. Usage ................................................................................................................................................................................................................................... 23
14.7. Legal guarantee ................................................................................................................................................................................................................ 23

INSTALLATION &USERS MANUAL FIREPLACE | SOL 60/70/80/90
2 | Page
1. ARTE®FIREPLACE -AGREEK QUALITY PRODUCT
Thank you for buying an ARTE®fireplace - we believe that you will have as much pleasure from our product as we have.
Your ARTE®fireplace is made in such a way, to extract the maximum possible energy from the wood with the minimum possible emissions,
using the most innovative technology and the most robust design - made in Greece!
These instructions contain interesting and informative facts and all you need to know about the subjects of heating, wood, and operating
your ARTE®fireplace. Please read these instructions carefully before using your fireplace for the first time and keep them in a safe place.
2. FACTS ABOUT WOOD AND THE ENVIRONMENT
2.1. Why use wood?
With proper forest management, burning wood does not deplete the earth’s resources. Heating with wood usually does not contribute to
global warming. The young trees that replace the trees in your fireplace absorb carbon dioxide from the air. Burning firewood releases only as
much CO2 as the tree has absorbed from the atmosphere during its growth. Wood rotting in the forest generates the same amount of CO2 as
the same wood burning.
Besides being environmentally friendly, the heat from a fireplace warms you like the warming rays of the sun during the sunny winter days. It is
the radiated heat that transmitted by electromagnetic waves in the infrared range. Even when the air is very cold you can feel the warm rays
of the sun on your skin.
Another advantage to wood is that it is produced locally, which creates local employment, and more tax revenues stay in the province.
2.2. Buying firewood
Where can I get my firewood?
Regenerated ready-to-burn firewood can be purchased from dealers:
Fireplace ready, stored for at least two years
Pre-dried, stored for one year
Fresh from the forest
Whether you have cut your own wood or bought it, the important thing is: the wood should be dried for at least two years before it is burned.
2.3. Storing your wood
The full potential for heat will not be realized if you neglect the simple chore of piling and protecting your wood. Proper storage is essential to
avoid moisture, bacteria, and insect problems in your home.
To avoid problems with insects and moisture, store the wood as far from your house as is practical. Do not store wood in your basement; one
cord of wood can give off more than 500 liters of water. The basic rule is to hide the wood from water, but not from the sun or wind (Pic. 2.3.1
& 2.3.2) Green wood will dry slowly or not at all if unprotected, while seasoned wood left unprotected may become unseasoned.
There are three basic rules to follow when storing wood:
Allow air circulation by piling one tier wide if possible
Protect wood from rain and snow by covering with a tarp or
woodshed roof.
Pile wood off the ground on scrap lumber or wooden pallets.
The time-honored way to cure wood is to buck, split, and stack
wood off the ground for one full year. How-ever, wood can
generally be reduced to 20 per cent moisture content in two to
three months. The ideal 10% to 15% may take longer (almost 18
months).
The ideal residual moisture is 12 - 15% and should be no higher!
The manuals which are enclosed with the product must be
kept throughout the product’s entire service life.
Pic. 2.3.1 Pic. 2.3.2

INSTALLATION &USERS MANUAL FIREPLACE | SOL 60/70/80/90
3 | Page
2.4. Wood types and calorific value
A wood’s efficiency does not depend only on its type, but also on its humidity, as well as the temperature of the combustion chamber.
For more efficient and longer burning, without emission of hazardous substances, woods must be dry. Ideally, their humidity percentage must
not exceed 10% to 15%.
If this percentage is over 20%, the wood is not burned properly, whereas if the piece of wood has been cut recently, the humidity is over 60%
making it unsuitable for burning. The reason for that is that the fire will be weak and pale and will produce dense smoke, unburned tar and
creosote, soiling the ceramic glass and the flu.
It is preferable to get your wood supplies during the summer months and store them, to ensure better combustion quality during the winter.
Useful tips
Always choose dry firewood.
Avoid wood that pops (chestnut, conifers such as cedar, spruce and pine), as they may damage your fireplace or the flue.
Pay attention to the size of the logs. Good firewood must have been cut at least twice.
You should prefer oak, beech, olive wood, which is hard wood with high density since they will burn for longer.
Briquettes
They ignite very easily, and burn slowly. They are economically advantageous because you will burn smaller quantities compared to common
firewood and they are easily stored. Also, you have less quantity of ashes vs. to wood.
Birch
It’s a soft wood that ignites easily with great thermal energy production. It produces less smoke and ash compared to other wood and burns
silently. The same characteristics apply for lime and chestnut.
WET
DRY
0% humidity
100% thermal efficiency
10%
humidity
88%
thermal efficiency
30%
humidity
63%
thermal efficiency
50%
humidity
39%
thermal efficiency

INSTALLATION &USERS MANUAL FIREPLACE | SOL 60/70/80/90
4 | Page
Beech
Hard wood is ideal for firewood but requires a high temperature to ignite. It
weights a lot; it is dense and burns with a calm and long fire for a longer time.
Best when well seasoned. The same applies for oak, but seasoned for 2-3
years.
The various wood types have various calorific values
Wood type Thermal capacity (Kcal/h-1Kg)
Briquette 5.000
Birch 4.800
Walnut 4.731
Oak 4.619
Beech 4.578
Fir 4.588
Common Oak 4.548
Pine 4.457
Olive 4.100
Poplar
4.022
Table 2.4.1
860Kcal/h = 1 kW/h
The values are based on 15% residual wood moisture.
2.5. Determining the heat output
There is not a specific rule that enables the calculation of the required heat output. This depends on the amount of space that is required to
be heated and mostly on its insulation. In average the required heat output for a properly insulated room and with external temperature of 0ο
is 40 kCal/h per m3.
Taking into account that 1kW equals 860 kCal/h an equivalent of 50W/m3can be used. For example, to heat a 50 m3room (10 x 6 x 2.5m) in
an insulated residence, the output required is 150m3x 50W/m3= 7500W or 7.5 kW.
So for the main heating, a 10kW appliance is enough.
Indicative combustion value
with efficiency ~80%
Required amount relative
to 1kg dry wood
Fuel Unit kCal kW
Firewood (moisture 15%) kg 3600 4.2 1.00
Firewood (moisture 50%) Kg 1850 2.2 1.95
Wood briquettes Kg 4000 5.0 0.84
Coal briquettes Kg 4800 5.6 0.75
Coal Kg 7700 8.9 0.47
Coke Kg 6780 7.9 0.53
Gas m37800 9.1 0.46
Diesel L 8500 9.9 0.42
Electricity kW/h 860 1.0 4.19
An ARTE®fireplace can be fired with all of the above wood types
Table 2.5.1

INSTALLATION &USERS MANUAL FIREPLACE | SOL 60/70/80/90
5 | Page
3. ENDORSEMENTS &CERTIFICATIONS
3.1. Endorsement
The ARTE® fireplace you chose has been tested according to EN13229.
3.2. Declaration of Performance CE
The constructor G. Karnoutsos & Co. declares that ARTE® fireplaces meet the requirements of the standard EN 13240, also the product’s
performance according to the quality specifications are monitored on a permanent basis.
3.3. Features marking plate
ARTE® fireplace’s feature marking plate is located on the right side of the appliance.
4. PACKAGING
ARTE® is devoted in protecting the environment, so we use as much recyclable materials as possible and the least amount of packaging
materials without compromising the secure transfer of our products.
4.1. Unpacking
1. The product will be delivered on a wooden palette which is lined with wooden side panels and top panel. (Pic. 4.1.1)
2. Remove the individual parts of the packaging, starting from the top and then the front, side and finally the back panel. (Pic. 4.1.2)
3. Carefully remove the plastic membrane and the waterproof plastic film and also all the polystyrene on the outside and inside of the
product.
4. Unscrew the 2 screws located on either side of the product, in order to release the fireplace from the palette. (Pic. 4.1.3)
5. Carefully pick up the product and place it on the installation point, making sure that the floor can withstand the weight of the device. If
the existing construction cannot withstand the weight of the device, a load distributing plate is necessary. Also, make sure you provide
proper insulation in case the floor is built using flammable materials.
Pic. 4.1.1 Pic. 4.1.2 Pic. 4.1.3

INSTALLATION &USERS MANUAL FIREPLACE | SOL 60/70/80/90
6 | Page
5. ASSEMBLY
5.1. Door opening side change
ARTE® SOL fireplace is delivered with the combustion chamber door opening on the left, still you have the potential to change it in order to
open on the right.
To change the opening direction of the combustion door, please follow the steps below:
1. Remove the hinge from the top left corner of the door, by unscrewing the two
hexagonal head screws.
2. Open the handle and tilt the door slightly to the front in order to remove the
rebound spring located on the left side of the door and then remove the
door.
3. Remove the handle along with the safety plate by unscrewing the three
hexagonal head screws.
4. Move and install the handle along with the safety plate on the left side of the
door by screwing the three hexagonal head screws.
5. Unscrew the door support pin using the hole on its body and install it on the
right side of the fireplace, along with the washer.
Then remove the rebound spring from the upper left side of the fireplace and
install it inversely opposite on the lower right side, next to the hinge.
6. Support the door on the lower right pin you installed and place the loose end
of the rebound spring on the corresponding hole on the center of the right
side of the door. Place a 3mm spacer between the door and the pin support
point (on the lower left side) and push the top side of door towards the
fireplace until you can close the handle.
7. Install the hinge along with its washer on the upper right corner of the door by
screwing the two hexagonal head screws, as you push the upper right corner
of the door towards the fireplace. Pay intense attention on keeping the hinge
parallel to the door!

INSTALLATION &USERS MANUAL FIREPLACE | SOL 60/70/80/90
7 | Page
5.2. Electrical installation
ARTE® SOL fireplace is constructed in way that it supports the installation of the power connections
to the control panel on either side of it. In order to install the power cord you must follow these steps.
1. Open the control panel door.
2. Remove the air intake filter.
3. Unscrew the four screws of the ventilator protective
panel. (Pic. 5.2.1)
4. Within the accessories delivered along with the
fireplace, you will find an elastic gasket and a power
cord which comes preinstalled with a quick lock jack.
Insert the gasket on the exit hole (Pic. 5.2.2) and once you connected the jack to the corresponding end of the control panel, pass the
power cord through the gasket from the inside out. In order to facilitate the installation, dribble 1-2 drips of lubricant on the power cord.
5.3. Revolving buffer installation
For safety reasons, ARTE® SOL fireplaces are delivered with the revolving buffer not
installed. It is essential that you install it prior to lighting the fireplace. In order to do so
you must insert the protruding pins on the left and right of the buffer in the
corresponding hooks that are located on the inside of the air curtain. (Pic. 5.3.1)
5.4. Fixing the handle
ARTE® SOL fireplaces gives you the option to fix the handle on the opening mechanism. In order to do so, you are
provided with a hexagon head M5x6 screw, which you screw on the designated place. (Pic. 5.4.1)
6. FIRE SAFETY
It is OBLIGATORY to respect the National and European rules and local regulations concerning building matter and fireproof rules.
The installation MUST be inspected by a qualified auditor, prior to lighting the fireplace. Also the appropriate local authorities must be
informed.
6.1. Safe distances
The combustion chamber opening must be AT LEAST 80cm away from any flammable materials that are inside the
heat radiation zone.
6.2. Wooden beams protection
Given its properties, heat is transmitted through radiation. In case there are any wooden beams inside the radiation zone or in the way of the
hot air, the MUST be properly insulated because the continuous exposure in high temperatures can make them deteriorate faster or even
cause self ignition. Use proper insulation materials that are in accordance with European rules or, in case of high thermal stress you can also
use metal linings.
The electrical installation must NECESSARILY be made by
qualified personnel
Pic. 5.3.1
Pic. 5.4.1
Pic. 5.2.2
Pic. 5.2.1
80
–
120
cm

INSTALLATION &USERS MANUAL FIREPLACE | SOL 60/70/80/90
8 | Page
6.3. General security instructions
Never leave children alone or without supervision near the fireplace when it is lit.
Teach children how to operate the fireplace correctly and safely.
Never touch the external surfaces of the fireplace or the glass when it is lit. There is a high risk of burns!
Due to the self closing door, you have to be extra careful when you are filling the fireplace.
It is forbidden to use the fireplace as a waste incinerator.
Don’t use burned or used wood as fuel.
Remove the ash only after it has completely cooled off.
Ash should be placed outdoors or be disposed in a place where there is no risk of ignition.
Immediately inform your specialized local supplier if you find any malfunction.
Don’t use chemicals or liquids as fire starters.
Do not use ANY fuel other than the recommended
6.4. Flue security instructions
Prior to installing the fireplace ARTE® the chimney sweep or a qualified technician should check the condition and operation of your chimney
in accordance with the standards EN13384-1 & EN13384-2.
This way you ensure the best conditions for heating without issues.
6.4.1. Basic requirements for proper flue operation
The internal section of the flue must preferably be circular. In a case of square or
rectangular flue, the internal corners should have a radius of at least 20mm. In case of
rectangular flue, the ratio of the sides should be at maximum 1: 1.5
The flue must be properly insulated and waterproof and constructed of materials with
thermal resistance and resistance to combustion products and any deposits.
The flue must have no constrictions; it must have a vertical path and it should not change in
direction that exceeds 45o. (Pic. 6.4.1.1)
In case of an existing flue the construction material should be checked. Materials such as
cement with lime, galvanized steel and rough or porous materials are contraindicated as
they create issues in the correct operation of the fireplace. Also, a proper study for the flue
size must be conducted because often old flues have quite large diameters. This means that
the amount of air draft is not proportional to the heat generated by the fireplace and by
extension means that you consume more wood than necessary and will spend more time
on maintenance. The solution proposed in these cases is the connection of an inner tube
inside the flue. This tube should extend over the whole length of the flue and at no point should exceed in diameter the outlet flue of the
fireplace. If the existing flue has the desired diameter a proper cleaning by qualified personnel should be done.
Inserting the pipe along the outer wall must be properly studied to avoid heat loss. This solution, however, is contraindicated, as positioning
the flue inside the house warms more spaces as heat of the flue remains in the house.
6.4.2. Chimney placement
The placement of the chimney on the roof is a particularly decisive factor in the convection of the fireplace.
An incorrectly fitted chimney may generate reimbursement of exhaust into the heating space due to down flow of the air.
Follow the instructions below to ensure proper dissipation of smoke. (Pic. 6.4.2.1)
The ending of the chimney must be at least 50cm above the top of the roof.
If there is more than one chimney on the roof, they must be positioned at least 2m apart.
If there are two adjacent chimneys, their ends must be at least 50cm apart.
If there is a tall building or tree next to the house, then you should place the chimney at a distance greater than 5m from the obstacle.
It is prohibited to connect several devices to the same chimney. Every chimney should be autonomous. (Pic. 6.4.2.2)
Follow the operating instructions supplied with the product to help prevent fire and
protect the environment.
Pic. 6.4.1.1

INSTALLATION &USERS MANUAL FIREPLACE | SOL 60/70/80/90
9 | Page
In case of an inclined roof, the height of the chimney is defined depending on the inclination and the distance of the chimney from the
ridge according to the following table. (Pic. 6.4.2.3)
Inclination
αο
RIDGE – CHIMNEY
DISTANCE
MIN HEIGHT
ABOVE THE RIDGE
Α(m) H (m)
15ο
< 1,85 m 0,50 m OVER THE RIDGE
> 1,85 m 1,00 m OVER THE ROOF
30ο
< 1,50 m 0,50 m OVER THE RIDGE
> 1,50 m 1,30 m OVER THE ROOF
45ο
< 1,30 m 0,50 m OVER THE RIDGE
> 1,30 m 2,00 m OVER THE ROOF
60ο
< 1,20 m 0,50 m OVER THE RIDGE
> 1,20 m 2,60 m OVER THE ROOF Pic. 6.4.2.3
6.4.3. Chimney cap
The chimney draft depends broadly on the adequacy of the cap.
So, in case the chimney is built, its exhaust diameter should be at least twice the inside diameter of the chimney. Knowing that it is necessary
to protrude from the ridge of the roof, the cap must ensure the proper smoke dissipation in case of strong wind.
A chimney cap must meet the following requirements:
Internal diameter must be equal to the diameter of the chimney.
Exhaust diameter be at least twice the inside diameter of the chimney.
It should be constructed in such a way as to avoid the entrance of rain, snow and any foreign body in the chimney
It can be checked, maintained and cleaned easily.
Industrial style cap with
protective net
Cap with deflector. It leans
according to the wind and it
provides very good smoke
dissipation.
Cap with fan. It provides
very good smoke
dissipation even in case
of weak winds.
Pic. 6.4.2.1
Pic. 6.4.2.2
Table 6.4.2.1

INSTALLATION &USERS MANUAL FIREPLACE | SOL 60/70/80/90
10 | Page
6.4.4. Connecting the fireplace with the flue
It is necessary that the flue gas tube is connected to a certified conduit with the
same diameter as the fireplace, by following the dimensions of the adjacent image.
(Pic. 6.4.4.1) For fireplaces SOL 60/70 the diameter of the flue is 150mm, while on SOL
80/90 is 180mm. The flue must be properly insulated with stone wool with thickness of
4cm with external aluminum foil. Do not use fiberglass or paper based insulation.
Also, do not use flexible thin walled metallic tubes or asbestos tubes. This tube should
be perfectly sealed and well insulated throughout its length.
To install the flue, you must first remove the two baffles (stainless and vermiculite)
from the top of the combustion chamber. Then you must remove the mounting
flange by unscrewing the five stainless steel screws that secure it to the chassis. Then
you will need to enter the flue in the combustion chamber where once you cover it
with sealant, you must connect it to the mounting flange and the connection to be
secured with a clamp. Finally you should place the gasket on the chassis and
tighten the five screws again.
Before installing a SOL fireplace in a wall you must ensure that there is a front
opening of at least 635/735/835/935x565mm, according to the type of the device.
In case you are installing a SOL fireplace on an existing fireplace you must close the inner part of the flue with
a deflector with an appropriately drilled plate or other refractory material that can withstand high
temperatures without damage.
The space extending around and over the device up to the deflector must be ventilated continuously. For
this reason you must allow cool air from a lower spot, for example, the bottom and the outlet of the hot air
from above. (Pic. 6.4.4.2)
These openings must remain free and not able to be covered. The must also have a minimum surface of
300cm2, for example, a grille with size 30x10cm.
This way you achieve:
greater security
Increase on the heat of the room, due to the air circulating around the device.
The hot air extract grille must be placed on top of the trunk approximately 20cm from the ceiling. The grille must always be installed, as its
purpose is to allow, the heat that builds up inside the trunk to be released in the room and also to relieve the pressure created.
6.4.5. Air supply to adjacent rooms
ARTE® SOL fireplaces have an option for connecting air tube and provide hot air in adjacent rooms. At the top of the device there are two
holes in which you can connect said conductors.
To install the conductors you must follow the procedure below:
1. Configure appropriately the adjacent walls or drywall to install air ducts, with maximum diameter of 150mm, which must be properly
insulated and do not exceed a horizontal displacement of 7m. When calculating the distance keep in mind that if the tube changes
course by 90oyou should calculate a horizontal path of 1m and if it changes 45oyou should calculate 0.5m.
2. Remove the hole covers by using a hammer. (Pic. 6.4.5.1)
3. Install the collars with diameter of 150mm on the holes and bend the mounting strips. (Pic. 6.4.5.2)
4. Mount the air ducts to the collars by using clamps. (Pic. 6.4.5.3)
Pic. 6.4.5.1 Pic. 6.4.5.2 Pic. 6.4.5.3
Pic. 6.4.4.1
Pic. 6.4.4.2
DEFLECTOR

INSTALLATION &USERS MANUAL FIREPLACE | SOL 60/70/80/90
11 | Page
The air ducts must be properly insulated to avoid noise and heat loss.
The output of the air ducts must be at least 2m above the floor so that the hot air is not directed straight on humans.
ARTE® SOL fireplaces enable the control of the air supply quantity on the front. This is achieved by using two adjustable flaps which are
regulated by using the handle and allow four different combinations.
1. Fully open
2. Left OFF – Right ON
3. Left ON – Right OFF
4. Fully closed
The use of adjustable flaps enables the user to be able to change the amount of air both locally and on the air ducts that provide hot ait on
adjacent rooms.
In case tubes over 7m are used, you must also install ventilators on the end of the tube in order to
propel the air. To prevent smoke transfer in an adjacent room, the use of an additional
component placed in the air outlet at the top of the device is required. (Pic. 6.4.5.4)
6.4.6. Malfunction - Secure fireplace shutdown
In rare occasions even a test fire may not cause sufficient draft in the flue. In this case contact your chimney sweep. Under no circumstances
should you try to light a larger fire. If smoke escapes from the fireplace, ventilate the room immediately and contact your chimney sweep.
DON’T LIGHT THE FIREPLACE!
7. OPERATING INSTRUCTIONS
7.1. Before initial use of an ARTE® SOL fireplace
One of our qualified dealers has already given you instructions on how to operate the ARTE® SOL fireplace you just bought.
In the guidelines below there are detailed instructions on the steps to follow so you do not encounter any issues during the operation of the
fireplace.
The qualified dealer in your area is at your disposal to answer any of your questions. The ARTE® SOL fireplace is equipped with the following
control systems:
7.2. About ARTE® SOL fireplace
The fireplace you just received is a device designed to offer excellent heating with very high efficiency. It is Insert type, which means that it
can be installed in an existing fireplace and thus upload the thermal rate of your room.
Opening the flap Closing the flap
Pic. 6.4.5.4
1
2
4
3
3
5
6
7
8
9
10
12
11
13
13
14
10

INSTALLATION &USERS MANUAL FIREPLACE | SOL 60/70/80/90
12 | Page
1
Main door with double ceramic glass
8
Opening hand
le storage location
2
Detachable main door opening handle
9
Log
rolling guard
3
Air intake filters
10
Vermiculite panels
4
Automatic combustion air regulator
11
Flue
5
Automatic
ventilator
control
panel
12
Sensors access slot
6
Control panel
door
ope
ning handle
13
Air outtakes for adjacent rooms
7
Control panel door micro switch
14
Main front air outtake
1
Hot air circulation space
6
Combustion air intake regulator
2
Vermiculite baffle
7
Lower air curtain
3
Secondary air int
ake
8
Upper air curtain
4
Combustion chamber
9
Stainless
steel
rotating baffle
5
Primary air intake
10
Stainless
steel
baffle
7.3. General information
7.3.1. When the fireplace paint dries
ARTE ® products are painted in spray booth with as more environmentally friendly and ecological colors as possible. There is although a
possibility that the first few times the fireplace is lighted, the paint emits an odor. Let the fire burn with intense convection until all traces of
gas disappear and there is no longer a smell. The gas is not toxic, but the room should be well ventilated.
7.3.2. Incineration preparation
Prepare sufficient amount of chopped firewood, kindling and branches or torches. Before using the wood it is recommended to store them
in a warm place for a few days.
7.3.3. Combustion air intake
ARTE® SOL fireplaces provide two different options for combustion air intake.
1. Use of internal air:
The presence of kitchen hoods, ventilation systems or other heating appliances may affect the operation of the fireplace. When operating
more than one device make sure that there is sufficient air intake. The simultaneous operation of a kitchen hood or a ventilation system
with the fireplace may draw in hazardous gases from the fireplace towards the interior of the room.
According to the operating regulations, the concomitant use of similar devices may be acceptable
only if there is a flue gas control device. When there is a kitchen hood, a ventilation system or other
heating appliances in use, at least one window in the room must remain open.
Opening the holes for the combustion air intake is IMPORTANT!
In case it is not done, there is serious risk of destroying the fireplace.
Use a hammer in order to remove the covers.
1
2
3
4
5
6
7
8
9
10
Table
7.2.1
Table
7.2.2

INSTALLATION &USERS MANUAL FIREPLACE | SOL 60/70/80/90
13 | Page
2. Use of external air:
Although the fireplace uses external air for combustion, make sure that the room is ventilated adequately when the fireplace operates
with external fresh air. When you open the door of the combustion chamber for adding firewood there should be no pressure difference
between outdoor and indoor air in the room, so it is good to keep the door open for about 1.5cm for 5-6 seconds and then fully open it.
ARTE® SOL fireplaces allow fresh air from two different inlets:
Inlet BEHIND Inlet BELOW
7.3.4. Power failure
In case of power failure, the automatic air flow regulation device in the combustion chamber is activated and almost immediately
reduces the flame intensity in order to reduce the temperature of the fireplace and protect the electrical components from overheating.
When the temperature drops to normal levels then the regulator smoothly feeds back air in the combustion chamber and the operation of
the fireplace is continued.
During a power failure you can light and operate an ARTE® SOL fireplace normally. The only difference would be that because the motors
are not quickly conferring heat in the room, the overheating safety system does not allow the device to operate at its nominal heat output
but at a lower. That is why ARTE® suggests using an uninterruptible power supply unit (UPS) with minimum output of 250W which will ensure
the smooth operation of the fireplace for about 2 hours.
7.3.5. Heating during seasonal change or in adverse weather conditions
When there is high humidity or fog, with temperatures ≥15 ° C, but also during the transitional period between seasons, it is recommended
to light a test fire before normally lighting the fireplace. This will displace the cold, heavy air that is inside the flue and create the right
conditions for optimum smoke dissipation.
In case there is no UPS installed, you can leave the control panel door open and
remove the air filters in order for the air to circulate freely and thus distribute the heat
in the room. When the power returns, after a while, the ventilators will start again.
Under no circumstance should you operate the fireplace with the main
door open. You run a serious risk of destroying the device.
During a power failure the hot air distribution
motors stop, but ARTE ® SOL fireplaces remain safe.
Use a hammer to remove the cover.
If you want to import air from an external source, you
must apply the corresponding 100mm diameter collar
and clamps to mount a flexible conduit.
The air inlet must be positioned so as not to allow being covered.
The air inlet must be communicating with the combustion space and
protected by a grille.
The minimum surface of the air inlet should not be less than ~110cm2
Avoid using air inlets connected with garages, kitchens,
bathrooms or boiler rooms.

INSTALLATION &USERS MANUAL FIREPLACE | SOL 60/70/80/90
14 | Page
7.4. Use of the electronic control panel
ARTE® SOL fireplaces incorporate two ventilators with total power output of 420m3/h, which are used for heating the air and redistribute it in
the room, which drastically increases the heating capability of the fireplace.
The motors are controlled by an electronic board which settings you can change using the control panel that is located beneath the control
panel door.
To turn the panel ON or OFF, press key A. The state ON/OFF is indicated through LED light L1.
>Operation MODES
1. MANUAL mode (indication MAN – LED light L2)
The ventilator operates at the selected speed regardless of the temperature of the sensor.
2. AUTOMATIC mode (indication MAN – LED light L3)
The ventilator operates at the selected speed when the sensor temperature is higher than that in which the thermostat is set (45oC).
3. PROGRESSIVE mode (indication PROP – LED light L4)
The ventilator automatically increases its speed according to the temperature of the sensor (starting from 45oC). In case you neglect to
turn on the thermostat before lighting the fireplace (it remains in OFF) and the sensor temperature exceeds 100oC, the ventilators are
automatically activated (ON) and start to operate in MANUAL mode, for 10 seconds and then it automatically switches to PROGRESSIVE
mode until the temperature drops to 90oC, in which case it switches back to MANUAL mode. This process is repeated continuously until you
choose another mode.
4. ALARM mode
If the temperature of the sensor exceeds 130oC, then a sound alarm is activated. You can turn that off for 5 minutes by pressing any key.
After five minutes, and if the problem is not yet restored, the alarm is activated again
>Main MENU
1. Mode selection
Press the MENU key (D) to view the selected mode, which is indicated on the screen and the corresponding LED light. By pressing the same
key again, you can choose one of the three operating modes appearing consecutively on the screen and are indicated by the
corresponding LED light. The setting is automatically stored in memory after 4 seconds. LED light L5 indicates the state of the ventilators.
2. Operation speed selection
By pressing keys Bor Cyou can view or change the current ventilation speed.
P0 = OFF (only for MANUAL mode)
P1 = Lowest speed setting
P10 = Highest speed setting
This function is not available in PROGRESSIVE mode.
In AUTOMATIC mode you can choose speed settings P1 ~ P10
>FAILURE or ALARM signals
The control panel can indicate possible sensor failures. In these cases it may display the following on the LCD screen:
LO: indicates low temperature (temperature lower than 0°C): The sensor is open or disconnected
HI: indicates high temperature (temperature higher than 180°C): The sensor has a short circuit
L1
L2
L3
L4
L5
A
B C D

INSTALLATION &USERS MANUAL FIREPLACE | SOL 60/70/80/90
15 | Page
8. LIGHTING THE FIREPLACE
8.1. Traditional method of lighting
Every time you light the fireplace, it initially requires large volumes of air. When the fireplace is cold, leave the door slightly open or secure the
handle (Table 7.2.1, Line 2) at the first stop in order for air to circulate around the door for the first few minutes and turn the automatic
combustion air regulator (Table 7.2.1, line 4) on position 9.
To form an adequate layer of ash at the base of the fireplace, use 1-2 kg of dry kindling the first time you light it. If it is possible, constantly
maintain a layer of ash with thickness of 2-3 cm at the base of the combustion chamber for added insulation.
1. Place 2-4 kindling tablets or 7-10 wrapped newspaper sheets beneath 1-2 kg dry kindling.
2. Turn the automatic combustion air regulator (Table 7.2.1, line 4) on position 9.
3. After the the ignition of the tablets/wrapped sheets, leave the door slightly open or secure the handle (Table 7.2.1, Line 2) at the first stop,
in order to ensure an adequate convection of the flue.
4. Once you ensure the flue is warm enough (after 5-10 minutes), close the door. If all required conditions are met, after 15-20 minutes a thick
layer of cinder will be formed in the combustion chamber and the temperature will rise, which is essential for the continuation of
combustion.
5. Once the requirement described in point 4 is met, place 2-3 logs with overall weight of 1.5-4.8kg, depending on the size of the fireplace, on
the cinder, with a distance of about 1cm from one another.
6. Open the air supply to the maximum level and close the door. The wood will begin to burn within 2-3 minutes. If not, open the door slightly
in order for enough air for combustion to enter. Close the door again once the wood ignites.
7. Lower the automatic combustion air regulator (Table 7.2.1, line 4) between positions 5 to 7, so that the combustion continues seamleassly
and ensure there is adequate air supply (oxygen) to maintain the flame clear and powerful when you reduce the amount of combustion
air and after.
8. As soon as the fire leaves a thick layer of cinder, you can add more firewood by repeating steps 5-7, every 45-55 minutes according to the
type of the device.
8.2. Lighting without CO emissions (FROM TOP TO BOTTOM)
1. Turn the automatic combustion air regulator (Table 7.2.1, line 4) on position 9. If needed, leave the door slightly open or secure the handle
(Table 7.2.1, Line 2) at the first stop, in order to ensure an adequate convection of the flue.
2. Place 2-3 logs with overall weight of 1.5-4.8kg and 30-60cm, depending on the size of the fireplace.
3. Place 2-3 kindling tablets or 5-8 wrapped newspaper sheets between the logs.
4. Add a few twigs (1-2 kg) on the top in zigzag arrangement.
5. Finally, place a medium log on top of the stack and light the tablets/wrapped sheets.
6. Once you ensure the flue is warm enough (after 5-10 minutes), close the door.
7. Lower the automatic combustion air regulator (Table 7.2.1, line 4) between positions 5 to 7, so that the combustion continues seamleassly
and ensure there is adequate air supply (oxygen) to maintain the flame clear and powerful when you reduce the amount of combustion
air and after.
8. As soon as the fire leaves a thick layer of cinder, you can add more firewood, every 45-55 minutes according to the type of the device..
Feed the fireplace often but with small amounts of firewood, at most 1.5-4.8kg, depending on the size of the fireplace, each time. If the
fireplace is overly full, t he generated heat may cause excessive strain on the flue. The supply of firewood should be done in moderation.
The openings of the secondary air supply
should not be covered by firewood.
To avoid covering the glass with soot, it is
important not to let logs lean against it.
Don’t leave the fireplace unattended as long as the door remains open.
Due to the self-closing door you should be very careful for
any accidents during the fueling of the fireplace.

INSTALLATION &USERS MANUAL FIREPLACE | SOL 60/70/80/90
16 | Page
Wood combustion rules
If you want less heat, put a smaller quantity of wood in the fireplace and reduce the amount of air. It is however important to maintain
an adequate layer of cinder.
Less heat = Less wood = Less air.
More heat = More wood = More air.
When the fireplace operates at excessively low power or if the wood is not sufficiently dry, soot might deposit on the glass.
9. TERTIARY COMBUSTION (PATENTED)
The three combustion points
The combustion of wood requires a process of primary, secondary, and tertiary combustion to be efficient.
1. Primary combustion
Primary combustion is the initial wood burning at relatively low temperatures. During the primary combustion, large amounts of soot, creosote
and gas are produced due to the existence of water in the wood. Creosote, in primary combustion, contains 60% of the potential energy of
wood, but it is deposited in the form of soot inside the fireplace and the flue without imparting any heating.
2. Secondary combustion
The combustion chamber is insulated so as to increase the temperature of the core and by providing just the right amount of oxygen
necessary to 600OC, the creosote ignites spontaneously. This creates a chain reaction that increases the temperature inside the fireplace from
600OC to about 870OC without having to add any more fuel. This is the secondary combustion.
Thereby, the more proper secondary combustion is achieved the higher temperatures are produced and the less residue is left (gas and
particles). The vast majority of secondary combustion is only done in the upper part of the chamber near the outlet of the flue. Thus a large
part of the heat that is achieved, is discharged directly through the draft of the flue to the exterior and not in the heating area.
ARTE’s® patented chamber manages to provide the maximum secondary combustion performance. An
automatic air intake regulating system in cooperation with four or five vertical ducts and the combustion
space having openings, in such a way as to insert the appropriate amount of hot air through the entire
length of the pipeline, onto the calcined side of the combustion space and the aircurtains of the
ceramic glass (Pic. 9.1.1), results in the fire receiving the right
amount of preheated oxygen throughout the combustion
chamber (Pic. 9.1.2). This way the whole area of the chamber is
converted in a secondary combustion chamber, not only the
upper part, and thus its performance dramatically increasies
and inversely gas residue reduces.
3. Tertiary combustion
The tertiary combustion occurs when the coal that remains on
the bottom burns in a proper and coordinated way. Coal
contains a large amount thermal energy that when used
provides a large amount of heat. Proper air flow directly on the
coals within such a hot room, results in almost complete consumption and minimizing the amount of ash
that collects on the bottom.
The fire should be vigorous and the smoke exiting from the flue must be almost
unnoticeable.
The fire should not be smoldering because it is causing more pollution.
If the door remains slightly open, fire gases and flames may escape from the opening of
the fireplace causing a risk of fire or asphyxiation. We recommend installing a smoke
detector in the room where the fireplace is located.
Under no circumstance should you operate the fireplace with the main door open. You
run a serious risk of destroying the device.
DO NOT OVERHEAT THE FIREPLACE! There is risk of fire or permanent damage. If any part
of the fireplace starts glowing, then the device is overheating.
Pic. 9.1.1
Pic. 9.1.2

INSTALLATION &USERS MANUAL FIREPLACE | SOL 60/70/80/90
17 | Page
10. CLEANING &MAINTAINING THE FIREPLACE
10.1. External maintenance
The fireplace surface is painted with heat-resistant paint. It is best kept clean by vacuuming with a soft brush attachment or by wiping with a
lint-free cloth. Over a period of time, the painted surface may become slightly grey. A canister of touch-up ARTE®spray paint should be
available from your fireplace supplier. This can be applied - in accordance with the instructions - in just a few minutes. When first firing, after
touching up, the fireplace will give off a slight smell as the paint cures. Make sure to ventilate the room well during this phase.
10.2. Internal maintenance
10.2.1. Ash disposal
Empty the excess ash as often as necessary in order for the level to remain below the appropriate (Pic.
10.2.1.1). ARTE® SOL fireplace is designed to produce the least amount of ash, almost 1Kg for every 100Kgs of
firewood. It is recommended to constantly maintain a layer of ash with thickness of 2-3 cm at the base of the
combustion chamber for added insulation.
Dispose the ash by following these steps:
Open the main door (Table 7.2.1, line 1) and use a small shovel or a scoop to remove the excess ash.
Dispose the ash in a metallic container with a tight lid
The closed container with the ash should be placed on a nonflammable floor or on the ground, away from flammable materials until the final
disposal of the ash. The ash must be stored in a closed container until cooled down, or buried on the ground or dispersed somewhere.
10.2.2. Glass
ARTE® SOL fireplace has a double ceramic glass in the window of the combustion chamber in order to the phenomenon of pyrolysis to
appear much faster. If the fireplace is generally operated at the correct temperature, there should be little or no soot on the glass. If it does
settle during lighting, most will burn off as temperature increases.
For normal cleaning, moisten a paper towel with warm water and add some ash from the combustion chamber. Rub it over the glass and
then clean the glass with clean water and dry it well. For heavier deposits that cannot be cleaned, use glass cleaner, applied when the glass
is cold, in accordance with the instructions.
Never use abrasive cleaners on the glass surface.
Reasons for the presence of dirt on the glass
Firewood is too wet
Logs are too large or not split
Combustion temeratures are too low
If there is a need to replace the glass, it should be replaced with the high temperature ceramic glass supplied by ARTE®. For more information,
please contact your local ARTE®dealer.
To reduce the risk of breaking the glass, avoid
striking the glass or slamming the door.
Replace broken glass IMMEDIATELY.
Do not operate the fireplace if the glass in the
door is damaged.
Never empty a fireplace while in use.
Never use your household or shop vacuum
cleaner to remove ash from the fireplace.
Always remove and dispose of the ash properly.
Due to the self-closing door you should be very careful for any
accidents during the maintenance of the fireplace
When performing maintenance on the fireplace, always
protect yourself, using safety goggles and gloves
Pic. 10.2.1.4

INSTALLATION &USERS MANUAL FIREPLACE | SOL 60/70/80/90
18 | Page
10.2.3. Gasket
The gasket around the perimeter of the door may harden over a period of time. It should be replaced if it becomes difficult to close the door
or if air starts to leak in around the perimeter of the doors, causing the fire to become a little less controllable. An ARTE®rope gasket kit is
available on your local ARTE®dealer.
10.2.4. Internal parts that need maintenance
The components that are in the flame route - consisting of the vermiculites, the ceramic glass, flue collar and stainless stell baffle - are subject
to extreme stress beacause of the heat produced by the fire. Occasionally, some of these parts may have to be replaced as part of routine
maintenance.
All of these service parts can be bought from your ARTE®dealer, and we recommend that damaged parts are replaced as soon as possible
to avoid consequential damage.
Should the baffle be distorted by overheating, the fireplace will still function, although its efficiency may be compromised. Please replace it as
soon as possible.
Internal wear accelerating factors
Regular overheating
Accumulated soot and ashes
10.3. Cleaning the fireplace and the flue
When wood is burned slowly, it produces tar and other organic vapors, which combine with emitted moisture to form creosote. The creosote
vapors condense in the relatively cool chimney flue. As a result, creosote residue accumulates on the flue lining. When ignited this creosote
makes an extremely hot fire.
Initially, do a monthly check for the presence of soot above the deflector plate and around the outlet flue. If the fireplace suddenly start
operating slowly check for intense presence of soot around the flue collar or in the flue / chimney.
Clean the flue/chimney all the way from the fireplace to the flue end point above the house. A good practice is to clean the flue after each
operating season and to inspect it prior to the start to ensure that bird’s nests or other blockages have not occurred during the off season.
10.3.1. Chimney sweeping
Inspect the fireplace regularly during the operating season as part of a regular maintenance schedule.
To inspect the chimney, let the fireplace cool completely. Then inspect the chimney through the flue collar by using a mirror. If you cannot
inspect the flue system this way, the fireplace must be disconnected to provide better viewing access
Clean the chimney using a brush with the same size and shape as the flue. Run the brush up and down the flue, causing any deposits to fall to
the bottom of the fireplace where they can be removed the same way as the ash.
If you cannot inspect or clean the chimney by yourself, contact your local ARTE®dealer or a professional chimney sweep.
If you experience a chimney fire, act promptly and:
Close the air regulation
Evacuate the house
Call the Fire Department
10.3.2. Annual maintenance
Before the operating season starts, perform a thorough cleaning, inspection and repair:
Thoroughly clean the chimney and flue connector
Inspect the chimney for damage and deterioration. In case of prefabricated chimney, replace any weak sections. In case of a masonry
chimney, have a mason make any needed repairs
The flue and its connector should be inspected at
least once every two months during the operating
season to determine if a creosote buildup has
occurred. If creosote has accumulated, it should be
removed to reduce the risk of a chimney fire
Components in the flame route, the gasket and the paint
finish are not covered by the warranty.

INSTALLATION &USERS MANUAL FIREPLACE | SOL 60/70/80/90
19 | Page
Inspect the flue connector and replace any damaged sections
Check the gasket for wear or compression, and replace if necessary
Check the ceramic glass for any cracks and replace if needed
Check the door and handle for tightness. Adjust if needed.
10.3.3. How to clean the inside parts of ARTE® SOL fireplace
During the annual visit of your local chimney sweep and during the cleaning of internal parts of the fireplace, it is recommended to remove
all internal parts of the combustion chamber to be also cleaned. Be careful because the vermiculite panels are porous and thus fragile.
(Chapter 10.4)
10.4. Internal parts removal
Removal of
stainless ste
el
rotating baffle
Removal of upper vermiculite panel
Removal of stainless stell baffle
Removal of back and side vermiculite panels
Maintenance on the fireplace must be done ONLY when the device is cold.
1
2
1
2
3
1
2