Artison RCC600-SM User manual

®
RCC~
INSTALLATION GUIDE
RCC600-SM
RCC600-FS
RCC600-SA
RCC600-CM
Subwoofer Module
Freestanding Subwoofer
Subwoofer Amplifier
Cabinet Mount

2

Thank you for choosing Artison's RCC 600 Subwoofer System. We are pleased
that you have selected our high-performance audio products.
INTRODUCTION
The following information will guide you through the installation and setup of your Artison
RCC 600 Subwoofer Module, RCC 600 Freestanding Subwoofer, RCC 600 Subwoofer
Amplifier and RCC 600 Cabinet Mount.
Your RCC600-SM carton should contain the following:
1 . RCC 600 Subwoofer Module
1 . RCC 600 Subwoofer Module Paint Shield
1 . RCC 600 Subwoofer Module Grille
1 . RCC 600 Subwoofer Module Wall Cut-out Template
Your RCC600-FS carton should contain the following:
1 . RCC 600 Freestanding Subwoofer
1 . RCC 600 Freestanding Subwoofer Grille
4 . Rubber Feet
Your RCC600-SA carton should contain the following:
1 . RCC 600 Subwoofer Amplifier
1 . Automatic Room Mode Correction™ (ARMCTM) Microphone Kit
2 . Rack-Mount Ears
6 . M3 Philips Head Rack-Mount Ear Screws
1 . ~ RU Blank Rack Spacer
1 . Remote Control
1 . Detachable IEC Power Cord
Your RCC600-CM carton should contain the following:
1 . RCC 600 Cabinet Mount
1 . RCC 600 Cabinet Mount Cut-out Template
If you are missing any of these parts or if you need assistance during the
installation of your RCC 600 Subwoofer System, please contact Artison's
Customer Service Department during normal business hours, Pacific Time at (775)
833-4344.
3

RCC 600 SUBWOOFER MODULE (RCC600-SM)
The RCC 600 Subwoofer Module can be installed into either an:
•Artison Pre-Build Box
(Volume::=:: 1.1 ft3) SOLD SEPERA TEL Y
OR
•Infinite Baffle
(Le. 2x4 stud wall, 16" On Center spacing at least 8feet tall, Volume 2.8 ft3
or greater)
IMPORTANT: In an installation of two RCC600-SM's that are being powered by one
RCC600-SA, both Subwoofer Modules need to be in either Pre-Build Boxes or be in
Infinite Baffles. You cannot connect two RCC 600 Subwoofer Modules that are in
different environments to the same RCC 600 Subwoofer Amplifier.
The front of the RCC600-SM and the grille are paintable. The RCC600-SM comes from the
factory with apaint-shield attached. When painting the RCC600-SM, ONLY paint the grille and
outer edge
of the module using the included paint-shield. DO NOT get paint on the rear of the
subwoofer module. Paint can damage the components which would VOID your Warranty.
The minimum mounting depth for the RCC600-SM is 3%" (95.5 mm), Le. a2x4 stud is 3~" deep
add
~", ~" or %" thick drywall and the RCC600-SM will fit. The maximum drywall thickness the
RCC600-SM can be mounted
in is 1.3125" (33.3 mm).
INSTALLATION WITH AN ARTISON PRE-BUILD BOX (Preferred Installation)
RCC600-IWPBB
1. Please refer to the Installation Guide included in the Artison In-Wall Pre-Build Box Carton for
installation instructions.
2. Using the speaker wire already run inside the Pre-Build Box manage both the positive and
negative conductors through the open tie-wraps on each side
of the RCC600-SM.
3. Connect the bare speaker wire ends to the spring-loaded binding posts, manage the speaker
wire back, tighten the tie-wraps and trim the excess.
4. Install the RCC600-SM into the pre-cut opening ofthe Pre-Build Box.
5. Carefully tighten the six dog leg clamps on the RCC600-SM using a#2 Philips Screwdriver.
6. The grille for the RCC600-SM is held in place by magnets. Simply position the grille on the
front
of the module into the recessed area.
NOTE:
While installing the subwoofer module make sure that any excess wire is run
properly so that it does not interfere with the driver's operation. The design of
the RCC600-IWPBB is such that there is NO clearance between the back of the
4

subwoofer module and the back of the box. Be careful that no wires are in this
area when installing the module.
RCC600-IFPBB
1. Please refer to the Installation Guide included in the Artison In-Floor Pre-Build Box Carton for
installation instructions.
2. Using the speaker wire already run inside the Pre-Build Box manage both the positive and
negative conductors through the open tie-wraps on each side
of the RCC600-SM.
3. Connect the bare speaker wire ends to the spring-loaded binding posts, manage the speaker
wire back, tighten the tie-wraps and trim the excess.
4. Install the RCC600-SM by lowering the module sideways, into the opening. Once the module
is
in the cavity it will rotate into the cutout.
5. Tighten the six dog leg screws with a#2 Philips screwdriver, atool with a90 degree bend is
recommended.
6. The grille for the RCC600-SM is held in place by magnets. Simply position the grille on the
front
of the module into the recessed area.
7. Using the supplied hardware install the 2L-Shaped Brackets to the inside of the box opening
and level the brackets with the level of the finished floor.
8. Install the Grate to the L-Shaped Brackets using the supplied hardware.
INSTALLATION INTO AN INFINITE BAFFLE
1. Use the provided Cut-out Template to mark the desired wall location. Be sure that no piping,
wall studs, or electrical wires interfere with the placement of the RCC600-SM.
2. Once the hole
is cut and the speaker wire is run, manage both the positive and negative
speaker wire conductors through the open tie-wraps
on each side ofthe RCC600-SM.
3. Connect the bare speaker wire ends to the spring-loaded binding posts, manage the speaker
wire back, tighten the tie-wraps and trim the excess.
4. Install the RCC600-SM into the cut-out made in the wall.
5. Carefully tighten the six dog leg clamps on the RCC600-SM using a#2 Philips Head
Screwdriver.
6. The grille for the RCC600-SM is held in place by magnets. Simply position the grille on the
front of the module into the recessed area.
NOTE: While installing the subwoofer module ensure any excess wire is run properly
so it does not interfere with the driver's operation.
5-

RCC 600 FREESTANDING SUBWOOFER (RCC600-FS)
SUBWOOFER PLACEMENT AND ORIENTATION
The RCC 600 Freestanding Subwoofer comes with four rubber feet to attach to the side
of your
choice. Carefully decide what placement and orientation are best for the subwoofer,
the
supplied rubber feet are not removable once applied. The classical rule for subwoofer
placement
is that the subwoofer should be placed near the same wall the front channels are
located, at one-third
of the total distance of the wall. When using multiple subwoofers, consult
with your dealer or custom installer for best placement options. This subwoofer
is not affected by
cabinet orientation and can
be used either vertically or horizontally. The normal vertical
orientation
is with the terminal cup facing down. The rubber feet will allow clearance for the
speaker wire to fit underneath. If the subwoofer is placed horizontally, the rubber feet should be
applied to the corresponding bottom side
of the cabinet.
SUBWOOFER SETUP
The RCC 600 Freestanding Subwoofer is to be used
in conjunction with the RCC 600 Subwoofer
Amplifier. On the rear
of the amplifier in the SETUP section, the EQ switch should be set to the
CLOSED BOX setting.
SUBWOOFER GRILLE INSTALLATION
The grille forthe RCC 600 Freestanding Subwoofer is held
in place with magnets. Simply position
the grille
on the front of the subwoofer into the recessed area.
\
6

RCC 600 SUBWOOFER AMPLIFIER (RCC600-SA)
The RCC 600 SubwooferAmplifier can be installed into eithercabinetry, on an equipment shelf, or
it can
be rack-mounted into astandard 19" Eauioment Rack. In anv installation be sure to
- -- - -- - - - -, I .,
provide adequate ventilation around the amplifier.
The RCC600-SA has two simple and conveniently placed mode settings. The Music or Movie
user controls are located on the front panel for selection based on the source material. The Mode
settings, Volume and Power Controls of the RCC600-SA can
be accessed via IR codes. The
remote included with your unit can
be downloaded into alearning remote or HEX Codes are
available on the Artison Web site. The Front Panel of the RCC600-SA has
an IR Receiver and
there is asecond hard wired feed thru jack that can
be connected to an integrated control system
on the rear panel. Each control is described
in detail below.
RACKMOUNT INSTALLATION OF THE RCC600-SA
1. Remove the amplifier's four feet from the bottom of the chassis.
2. Attach the included rack-mount ears to the front sides ofthe RCC600-SA.
3. Mount into the 19" equipment rack, the amplifier will occupy 1.5 RU. Using the supplied
.
~ RU Blank Spacer either above or below the amplifier will occupy 2RU.
4. If installing two RCC600-SA then the rack-mount ears can be flipped to accommodate the two
amplifiers
in 3RU.
RCC600-SA REMOTE CONTROL
The remote control has the following functions:
1. ON/OFF -This will toggle between Standby Mode (Amber Halo) and ON (Blue Halo).
2. MUSIC -This selects the MUSIC Ea. When active it will have aRed Halo added to the Blue
Halo.
3. MOVIE -This selects the MUSIC Ea. When active it will have aRed Halo added to the Blue
Halo.
4. GAIN -This will raise and lowerthe volume
of the amplifier. Aremote orthe Gain Knob on the
front panel can both be used to raise or lower the volume. NOTE: The
gain control is
configured so that the "last used" device setting will be remembered by the amplifier.
7

RCC600-SA FRONT PANEL CONTROLS
'"
/
RCC~LJJ
GAIN DIM
POWER
MUSIC MOVIE
-0-
<0
0000
o • 10
RTISON
1/
'"
GAIN -The position of this knob controls the overall gain (volume) of the subwoofer. Press
this button
in and it will spring out into arotating knob, press it back in to hide it. The front panel
gain control will become the master gain control until the remote
is used. NOTE: The
amplifier by default will resume to the last setting by either gain control device.
DIM -This button controls the brightness of the Halo lighting on the front panel. There are
four brightness settings.
POWER -This button will toggle between Standby Mode (Amber Halo) and ON (Blue Halo).
MUSIC -This preset EQ mode should be used for music playback. This EQ setting provides
afull range
of musical bass to enhance the listening experience, when active it will add aRed
Halo to the Blue Halo.
MOVIE -This preset EQ mode should be used for movie playback. This EQ setting adds
more volume and bass to help recreate the true movie theater experience, when active it will
add aRed Halo to the Blue Halo.
RCC600-SA REAR PANEL
POWERMOOES EO MOOES ~.,-AUDIO INPUTS
SETUP MODES -y-- AUDIO OUTPUTS- _____
AC POWER
120VAC-flOHz Fuse:T10AL
230VAC-50Hz Fuse:T5AL
GIII[] 0
ACMAINS POWER
1. The Power Switch is the hard ON/OFF power switch for the amplifier.
2. The Red Switch
is the input voltage setting; select the appropriate 120V or 230V setting.
3. Connect the detachable IEC Power Cord underneath the Red Voltage Selection Switch.
8

AUDIO OUTPUTS
_---- AUDIO OUTPUTS ----_
@@@@
I I I I
{>--SUB1~ ~SUB2--<}
1. Connect the speaker wires to the Binding Posts. NOTE: Red is Positive and Black is
Negative.
2. Use either Bare Speaker Wire or Banana Plugs to terminate the speaker wire.
AUDIO INPUTS
_- AUDIO INPUTS
UNBALANCED
GL
@
G"
BALANCED
1. Connect to either the Balanced Female XLR or Unbalanced Female RCA Inputs.
NOTE:
Both inputs have been calibrated to the same sensitivity level.
IR FEEDTHRU
IR
o
1. Connect a%" Stereo MINIJACK to control the RCC600-SA via your integrated control
system.
2. Both the IR Feedthru Jack and the Front Panel IR receiver are designed to allow the User
functions to be programmed into an external remote. The Hexadecimal codes for the
amplifier are located on the web at: http://www.artisonusa.com
9

POWER MODES
POWER MODES
II::
W
0"
.... "
z :::> iii: +12V
o< .... TRIGGER
r:t=J INPUT
rn
1. Select either:
ON -Always On.
AUTO - On with Signal Sense, without signal it will stay on for :::::15 minutes.
TRIGGER -On with a12 Volt trigger.
2. +12V
Trigger Input -Use the Green Phoenix Connector to connect a12 volt trigger wire
from your other equipment, the polarity on the connector can be either way.
SETUP MODES
-- SETUP MODES --
PHASE LOW PASS
80Hz.
O'~l00' 4OHz~60Hz
OJ OJ
----J L.- ---J L-
eo Bame CLOSED 12<1B 24dB
EQ BOX SLOPE
1. EQ -Select the appropriate setting based on these guidelines:
00 Baffle -The RCC 600 Subwoofer Module is installed in awall that has an air
volume
of ~2.8 fe.
CLOSED BOX -The RCC 600 Subwoofer Module is installed in an Artison In-Wall
or In-Floor Pre-Build Box, or is the RCC 600 Freestanding
Subwoofer.
IMPORTANT: In an installation of two RCC600-SM's that are being powered by one
RCC600-SA, both Subwoofer Modules need to be in either Pre-Build Boxes or be in
Infinite Baffles. You cannot connect two RCC 600 Subwoofer Modules that are in
different environments to the same RCC 600 Subwoofer Amplifier.
10

2. PHASE -Comes from the factory set at 0°. The phase of the subwoofer can be adjusted
to fine tune the signal coincidence
of the subwoofer and the lowerfrequencies ofyour LCR
Speakers. Adjust the phase, listening for
an increase in mid bass in the crossover region.
Apink-noise generator or
an RTA(Real-time Analyzer) can further analyze your
installation.
3. LOW PASS -This is the crossover frequency setting of the Low Pass Filter. The
RCC600-SA comes from the factory with the 80Hz setting that is recommended for use
with the Artison LCR speakers. If used
in conjunction with any other speakers consult with
the manufacturer for the correct setting for the integration
of the subwoofer with the
satellites.
4. SLOPE -Select either 12 dB/octave or 24 dB/octave for the slope of the Low Pass Filter
based on the correct frequency response at the crossover point. This can be done by
measurement or simply listening to the system. Aproper crossover will not have an
apparent "hole"
in the response norwill it exhibit the "bloated" mid bass sound that apeak
will create. Again, an RTA can come
in handy during this part of the set up.
EQ MODES -
Automatic Room Mode Correction (ARMC)
The amplifier comes from the factory set to BYPASS. This setting produces aflat frequency
response at the subwoofer module.
In some cases your room response may benefit from
ARMC. Eigen-modes, also known as room modes, exist
in all rooms. These room modes are
an interaction between the listening room itself, the location of the subwoofer, and the low
frequency wavelengths being on the same order as the room dimensions. This interaction
causes peak and null energy areas
in your listening room which differ depending on the room
and the subwoofer location.
The ARMC program was designed to send aseries of tones thru the RCC600 and then
analyze the system response at the microphone position. The program then reduces the level
of the frequency bands that have energy peaks caused by the room modes. As aby product,
after the ARMC process has been completed the overall subwoofer amplifier gain may need
to be raised to achieve the previous volume levels.
Ifyour normal listening position is located
in anull, then the only way to truly even out the null
is by either moving the subwoofer location to change the room modes that are stimulated OR
install adistributed bass system. Distributed bass uses multiple subwoofers
in different
locations
in order to stimulate more of the room modes. It has been shown that this type of
system mitigates Eigen-modes and provides amore uniform response to awider listening
area. Each RCC600-SA has the capability for running two RCC600-SM, or two RCC600-FS.
11

_-- EQ MODES ---.
fI'J 0
fI'J w
~ ~
>- :)
m«
to
C~R"~ JMITO EO
MIC
°O@
1. AUTO EQ MIC -This is the input jack for the ARMC Microphone.
2. Switch Settings -Select either:
a. BYPASS -ARMC not active.
b. AUTO EQ. -ARMC active. Will remember the last measured room mode sequence
and settings.
3. BLUE LED STATUS INDICATOR
a. Continuous Short Flash -Switch in AUTO EO setting, ARMC not yet saved. Since
the amplifier leaves the factory with this function having been tested the LED should
not flash continuously even when the switch is set to the AUTO EO position. NOTE:
It
is important that you do a room mode set up using the supplied microphone at
your normal listening position if you plan to use the amplifier in this setting
b. One Long, Two Short Flashes -Amplifier Error, Shorted Audio Outputs. Remove
the speaker wires from the amplifier and use an ohm meter to check for shorts
in the line.
c. One Long, Three Short Flashes -Over Temperature Indicator. Be sure that the
amplifier has adequate ventilation. If the situation continues to exist contact
Artison.
4. Calibrate Button -Place the supplied microphone in the desired listening position and
plug it into the AUTO EO MIC input jack. Press the button for afew seconds to initiate
ARMC sequence.
12

RCC 600 CABINET MOUNT (RCC600-CM)
The RCC 600 Cabinet Mount is an accessory to the RCC 600 Freestanding Subwoofer. The
RCC600-CM allows the RCC600-FS to
be hidden inside of any piece of furniture or built-in
cabinetry. The subwoofer is designed to fit snuggly inside the cabinet mount and direct the
subwoofer's energy down through the bottom
of the cabinet and eitherdirectly into the room or out
through vents
in the cabinet's baseboard.
INSTALLATION
1. Using the supplied Cut-Out Template mark the 12 mounting holes and the cut-out area.
2. Remove the cut-out by using the appropriate method for your application.
3. Mount the cabinet mount to the bottom of the cabinet via the 12 mounting holes in the mount.
Drywall screws approximately 2.5" long are needed to secure the mount or use hardware that
is more appropriate to your application.
VENTING SPECIFICATIONS
When venting the output
of the subwoofer through abuilt-in cabinet's baseboard, please
reference the points below:
a. Please allow for aminimum of 80 in
2
of total open area in the baseboard. If less open area
is provided the subwoofer will be restricted and may cause excessive noise through the
vent.
b. Rounded corners will also minimize noise caused by the excited air.
c. Either multiple smaller vents or one large vent can be used. The subwoofer is not affected
by variations
in shape or number of vents, as long as the minimum total open area is
maintained.
13

LIMITED WARRANTY
ALL INTERNET SALES ARE STRICTLY PROHIBITED
This warranty remains in effect for five years from the date of purchase for speaker
products and one year for electronic products.
THIS WARRANTY PROTECTS THE ORIGINAL OWNER PROVIDING THAT THE
PRODUCT HAS BEEN PURCHASED FROM AN AUTHORIZED ARTISON DEALER IN
THE UNITED STATES. THE ORIGINAL BILL OF SALE MUST BE PRESENTED
WHENEVER WARRANTY SERVICE IS REQUIRED. FOR WARRANTY SERVICE
OUTSIDE THE UNITED STATES, CONTACT THE AUTHORIZED ARTISON
DISTRIBUTOR IN THE COUNTRY WHERE THE PRODUCT WAS PURCHASED.
Except as specified below, this warranty covers all defects in material and workmanship.
The following are not covered: Damage caused by accident, misuse, abuse, product
modification or neglect, damage occurring during shipment, damage from failure to follow
instructions contained in the Owners Manual, damage resulting from the performance of
repairs by someone not authorized by Artison, or any claims based on
misrepresentations by the seller. This warranty does not cover incidental or
consequential damages. It does not cover the cost of removing or reinstalling the unit.
THIS WARRANTY IS VOID IF THE SERIAL NUMBER HAS BEEN REMOVED OR
DEFACED, OR IS PURCHASED ON THE INTERNET, WORLD WIDE WEB, MAIL
ORDER, 800, 888, 877 TELEPHONE NUMBERS OR THROUGH A CATALOG.
This warranty gives you specific legal rights. You may also have other rights, which vary
from state to state. Some states do not allow the exclusion or limitation of incidental or
consequential damages or limitations on how long an implied warranty lasts, so the above
may not apply to you.
Please make note of the following information and retain for your record.
Product Name Model Number _
Store Name Purchase Price
----------- ---------
HOW TO OBTAIN SERVICE
Please call us at [phone], or write to: ARTISON (Attention: Customer Service
Department), 774 Mays Blvd., Suite 10-183, Incline Village, NV 89451.
We will promptly advise you of what action to take. We may direct you to an authorized Artison
Service Center or ask you to send your speaker to the factory for repair. You will need to present
the original bill
of sale to establish the date of purchase. PLEASE DO NOT SHIP YOUR
ARTISON PRODUCT TO THE FACTORY FOR REPAIR WITHOUT PRIOR AUTHORIZATION.
PLEASE DO NOT RETURN PRODUCT TO THE ABOVE ADDRESS, IT IS NOT ASERVICE
LOCATION. You are responsible for transporting your product for repair and for payment
of any
initial shipping charges. However, we will pay the return shipping charges if the repairs are
covered under warranty.
14

..
213mm --
I
Mounting Hr1e Cutout Dimensions
Cut out opening
Mark the cutout area by
drawing through the
slots surrounding the
white area.
01
c..v
N
3
3
0)
.J::=.
o
3
3
TEMPLATE
s:
0m
c
Lh
~
:J
><
WARNING!
~
~
CD
Only cut out the mounting hole after
:J
....,
(Q
_.
you have verified there are no 0
I
....,
obstructions behind the dry wall. 0
"'U
£Before installing check for &-
....,
CD
0
obstructions behind drywall by
()
c..
making asmall hole. C
C('")
~
0
~
C0
~
_.
03
_.
CD
3
:J
CD
en
_.
:J
0
en
:J
_.
en
0
:J
en
---e- -----
~I
I
~ .... --- 282mm ----- Exterior Product Dimensions ------+--~
•

~ 207mm - Mounting He1e Cutout Dimensions ~
I
Cut out opening
Mark the cutout area by
drawing through the
slots surrounding the
white area.
(]I (]I
-......J CD
o -......J
3 3
3 3
TEMPLATE
s::
0m
c
&
~
:::J
><
WARNING!
~
~
--
CD
Only cut out the mounting hole after
:::J
..,
CO
--
you have verified there are no 0
I
..,
obstructions behind the dry wall. 0
""U
£Before installing check for &-
..,
CD
0
obstructions behind drywall by
()
a.
making asmall hole. C
C(")
~
~
0
C0
~
--
03
--
CD
3
:::J
CD
en
--
:::J
0
en
:::J
--
en
0
:::J
en
........ .....--- 242mm
~I
..... f
--- Exterio:r Product Dimensions ----------~

Name
Address
Company
Telephone Number
Email Date/Price
Name of Dealer
Address of Dealer
Product(sl
Model Numbers
Senal Numbers
Please rate your overall experience with the dealer 0 Exce!lent 0 Good 0 Average r.J Poor
2 Where did you first learn about ARTISON? 0 Magazine 0 Newspaper 0 Friend 0 Salesperson 0 Brochure 0 Other _
3 What other brand of speakers/subwoofers did you consider? 0 Polk 0 Bose 0 Sonance 0 Infinity 0 JBL 0 Boston Acoustics 0 Mirage
o Paradigm 0 Niles 0 KEF 0 Definitive Technologies 0 Other _
4 Please check the most important factors influencing this purchase?
o Ouallty of sound 0 Magazine Review 0 Recommendation of salesperson 0 Appearance 0 Technical Specifications 0 Ease of operation
o Recommendation of friend/family 0 Value for price 0 ARTISON's reputation 0 Previous owner of ARTISON's products
o Otller . _ o
Movie/Home Theater
o Over $100.000
o 55-64 0 Over 64
o $75.000 - $100.000
~
5 What IS the primary use for this purchase? 0 Music playback 0 Front main speakers 0 First speaker purchase
o Rear (surround sound)' speakers 0 Replacing speakers 0 Add to existing system 0 Other _
6 Which of these specialty magazines do you read? 0 Sound & Vision 0 Audio Video Interiors 0 Stereophile 0 Stereophile GUide to Horne Theater
U Absolute Sound U Architectual Digest 0 Consumer Reports 0 Horne Theater 0 Other . _
7 0 Male U Female 8 Age Group? U Under 18 0 18-24 LJ 25-34 035-44 045-54
9 Family II1come? U Under $15.000 U $15.000 - 24.999 0 $25.000 - $49.000 0 $50,000 - $74.999
10 Education (Please Check which category appliesl U High School U Some College CJ Completed College 0 Graduate School
11 What IS your occupation? 0 Self employed/Owner 0 Student CJ ProfeSSional Technical 0 Homemaker 0 Upper Management
Q Retired 0 Middle Management 0 Sales/Marketing 0 Clerical/Service Worker 0 Laborer/Tradesman
12 Do you have any comments about your new ARTISON products? _
o Yes, I wOlild like to receive ARTISON mailings when they become available 0 No. Please do not send me ARTISON mailings
WE WOULD LIKE TO THANK YOU FOR CHOOSING ARTISON
At Artisan. we are dedicated to tile art and technology of sound. providing you with high quality products that bring you closer than ever to the live
performance In order to maintain our high standards. we would like to better understand your needs. please fill out this questionnaire card and return It to
us Within TEN days
LIMITED WARRANTY
ThiS warranty remains in effect for five years from the date of purchase for speaker products and one year for electronic products
TH!S WARRANTY PROTECTS THE ORIGINAL OWNER PROVIDING THAT THE PRODUCT HAS BEEN PURCHASED FROM AN AUTHORIZE[} ARTISON DEALER IN THE
UNITED STATES THE ORIGINAL BILL OF SALE MUST BE PRESENTED WHENEVER WARRANTv SERVICE IS REOUIRED FOR WARRANTY SERVICE OUTSIDE THE
UNITED STATES. CONTACT THE AUTHORIZED ARTISON DISTRIBUTOR IN THE COUNTRY WHERE THE PRODUCT WAS PURCHASED
Except as specified below. this warranty covers all defects in material and workmanship The following are not covered: Damage caused by accident.
misuse. abuse. product modification or neglect. damage occurring during shipment. damage from failure to tallow instructions contained in the owners
manual. damage resulting from the performance of repairs by someone not authorized by Artisan. or any claims based on misrepresentations by the seller
ThiS warranty does not cover incidental or consequential damages. It does not cover the cost of removing or reinstalling the unit. ThiS warranty is void if
the sellalnumber has been removed or defaced
VOIl are responsible for transporting your product for repair However. Artisan will pay return freight charges if the repair is covered under warranty
ThiS warranty gives you specific legal rights Vou may also have other rights which vary from state to state Some states do not allow the exclusion or
limitation of incidental or consequential damages or limitations on how long an implied warranty lasts. so the above may not apply to you
Please make note of the follOWing Information and retain for your record
Product Name Model/Serial Number _
Store Name _
Purchase Price
HOW TO OBTAIN SERVICE
Please call us at 1775) 586-9574. or write to ARTISON (Attention Customer Service Departmentl. 774 Mays Blvd, Suite 10-183. Incline Village. NV 89451.
We will promptly adVise you of what action to take We may direct you to an authorized Artisan Service Center or ask you to send your speaker to the
factory for repair. Vou will need to present the original bill of sale to establish the date of purchase PLEASE DO NOT SHIP vOUR ARTISON PRODUCT FOR
REPAIR WITHOUT PRIOR AUTHORIZATION PLEASE DO NOT RETURN PRODUCT TO THE ABOVE ADDRESS. IT IS NOT A SERVICE LOCATION vou are responsible
for transporting your product for repair and for payment of any initial shipping charges However, we will pay the return shipping charges if the repairs are
covered under warranty.

ARTISON
Attention: Customer Service Department
774 Mays Blvd., Suite 10-183
Incline Village, NV 89451
Place
Stamp
Here